33.180.10 光纤和光缆 标准查询与下载

YD/T 2159-2022 接入网用光电混合缆

本文件适用于接入网通信远供电源系统中同时传送光信号和电能用混合缆的设计、制造和检验，接入网中同时传送光信号和/或电能、电信号用的混合缆也可参考使用。

Optical and electrical hybrid cable for access network

YD/T 4080-2022 通信电缆光缆用绕扎材料

本文件适用于通信电缆光缆绕扎用聚酯带、无纺布带和扎纱的生产和检验。

Winding materials for communication cables and optical cables

IEC TR 61292-12:2022 光学放大器.第12部分:空分多路传输用光纤放大器

Optical amplifiers - Part 12: Optical fibre amplifiers for space division multiplexing transmission

T/WHAS 020-2022 吸氢纤膏

本文件规定了吸氢纤膏的要求、试验方法、检验规则、标志、包装、运输和贮存。

Hydrogen fiber cream

BS EN IEC 60794-3-40:2022 光纤电缆 室外电缆 暴风雨和生活污水管道电缆系列规范

1   Scope This part of IEC 60794 is a family specification that covers sewer cables and conduits for installation by blowing and/or pulling in man accessible and non-man accessible storm and sanitary sewers. Systems built with components covered by this document are subject to the requirements of sectional specification IEC 60794‑3. Sewer cable and conduit constructions need to meet the different requirements of the sewer operating companies and/or associations regarding chemical, environmental, operational, cleaning and in general maintenance conditions. Preferential applications, describing sewer cable characteristics versus methods of installation is reported in Annex A and Annex B for non-man accessible sewers. Clause 5 describes characteristics of sewer cables and conduits for installation by blowing , pulling or other means in storm and sanitary sewers. Detail specifications can be prepared on the basis of this family specification. It is important that acceptance criteria are interpreted with respect to this consideration. The number of fibres tested is representative of the sewer cable and is agreed between the customer and the supplier.

Optical fibre cables - Outdoor cables. Family specification for cables for storm and sanitary sewers

EN IEC 60793-1-1:2022 光纤 第 1-1 部分：测量方法和测试程序 总则和指南

IEC 60793-1-1:2022 is available as IEC 60793-1-1:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60793-1-1:2022 lists and gives guidance on the use of documents giving uniform requirements for measuring and testing optical fibres, thereby assisting in the inspection of fibres and cables for commercial (mostly telecommunications) purposes. The individual measurement and test methods are contained in the different parts of the IEC 60793 series. They are identified as IEC 60793-1-X, where "X" is an assigned sub-part number, indicating its affiliation to the IEC 60793-1 series. In general, measurements and tests methods apply to all class A multimode fibres and class B and class C single-mode optical fibres covered by the IEC 60793-2 series relating to product specifications, although there can be exceptions. Clause 1 of each part of the IEC 60793 series contains the scope for each particular attribute. This fifth edition cancels and replaces the fourth edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - changes in normative references; - renamed Clause 10 and added documentation-related requirements in a new subclause 10.2.

Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance

BS EN IEC 60793-2-10:2019+A1:2022 光纤 产品规格 A1 类多模光纤截面规范

Optical fibres - Product specifications. Sectional specification for category A1 multimode fibres

22/30459633 DC BS EN 60793-2-50 ED7 光纤 第 2-50 部分 产品规格 B 类单模光纤截面规范

BS EN 60793-2-50 ED7. Optical fibres - Part 2-50. Product specifications. Sectional specification for class B single-mode fibres

KS C 6953-2022 全塑料多模光纤线

All plastic multimode optical fiber cords

KS C 6954-2022 全塑料多模光纤

All plastic multimode optical fibers

22/30456060 DC BS EN 60793-1-45 Ed.3.0 光纤 第 1-45 部分 测量方法和测试程序 模场直径

BS EN 60793-1-45 Ed.3.0. Optical fibres - Part 1-45. Measurement methods and test procedures. Mode field diameter

IEC 60793-1-1:2022 光纤.第1-1部分:测量方法和试验程序.总则和指南

Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance

IEC 60793-1-1:2022 RLV 光纤.第1-1部分:测量方法和试验程序.总则和指南

Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance

22/30456056 DC BS EN IEC 60793-1-41 光纤 第 1-41 部分：测量方法和测试程序 带宽

BS EN IEC 60793-1-41. Optical fibres - Part 1-41: Measurement methods and test procedures. Bandwidth

BS EN IEC 60794-1-404:2022 光纤电缆 通用规范 基本光缆测试程序 电气测试方法 电流-温度测试 方法 H4

This part of IEC 60794 defines a test standard to determine the optical performance and temperature characteristics of a hybrid cable under the maximum current. This document applies to optical phase conductor (OPPC). An optical phase conductor is made of multiple metallic wires that are exposed to the environment without any insulating or protective sheath and contain optical fibres.

Optical fibre cables - Generic specification. Basic optical cable test procedures. Electrical test methods. Current-temperature test, method H4

BS EN IEC 60794-3:2022 光纤电缆 室外电缆 截面规格

1   Scope This part of IEC 60794 specifies the requirements for optical fibre cables and cable elements which are intended to be used externally in communications networks. Other types of applications requiring similar types of cables can be considered. Requirements for cables to be used in ducts, for directly buried applications, aerial cables and cables for lake and river crossings are included in this document. Also included are cables for specialized use in sewers and in water and gas pipes. For aerial application, this document does not cover all functional aspects of cables installed in the vicinity of overhead power lines. For such applications, additional requirements and test methods can be necessary. Moreover, this document excludes optical ground wires and cables attached to the phase or earth conductors of overhead power lines. For cables for lake and river crossings, this document does not cover methods of cable repair, nor repair capability, nor does it cover cables for use with underwater line amplifiers.

Optical fibre cables. Outdoor cables. Sectional specification

22/30457569 DC BS EN IEC 60794-1-212 光纤电缆 第 1-212 部分 通用规范 基本光缆测试程序 环境测试方法 两端固定电缆元件的温度循环 方法 F12

BS EN IEC 60794-1-212. Optical fibre cables - Part 1-212. Generic specification. Basic optical cable test procedures. Environmental test methods. Temperature cycling with cable elements fixed at both ends, Method F12

BS EN IEC 60794-1-219:2022 光纤电缆 通用规范 基本光缆测试程序 材料相容性测试 方法 F19

1   Scope This part of IEC 60794 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, as well as hybrid telecommunication cables having a combination of both optical fibres and electrical conductors. The object of this document is to define test procedures to be used in establishing uniform requirements for the material compatibility performance of cables, cable components, and cable subassemblies. Compatibility of materials within a cable has the potential to involve a range of material pairs. However, experience has shown that the most pertinent evaluations are of the cable filling and flooding materials' interactions with other materials in the cable. NOTE Throughout the document the wording “optical cable” can also include optical fibre units, microduct fibre units, etc. See IEC 60794‑1‑2 for general requirements and definitions, as well as for a reference guide to test methods of all types.

Optical fibre cables - Generic specification. Basic optical cable test procedures. Material compatibility test, method F19

IEC 60794-3-40:2022 光纤电缆第3-40部分:室外电缆雨水和卫生下水道用电缆系列规范

Optical fibre cables - Part 3-40: Outdoor cables - Family specification for cables for storm and sanitary sewers

IEC 60794-1-310:2022 光缆.第1-310部分:总规范.基本光缆试验程序.电缆元件试验方法.可剥离性 方法G10

Optical fibre cables - Part 1-310: Generic specification - Basic optical cable test procedures - Cable element test methods - Strippability, method G10