33.180.99 其他光纤设备 标准查询与下载

IEC 62496-3:2011 光学电路板.第3部分:性能标准.总则和指南

This part of IEC 62496 covers general information on optical circuit board performance standards. It defines those tests and severities which form the performance categories or general operating service environments and identifies those tests which are considered to be product-specific. Test and severity details are given in Annex A. IEC 62496-3 provides references, definitions and rules for creating optical circuit board performance standards, as well as related information pertinent to the subject. Subsequent parts of the IEC 62496-3 series are sequentially numbered and contain performance criteria for specific applications. Each part will be added as the performance criteria become standardized for international use.

Optical circuit boards - Part 3: Performance standards - General and guidance

YD/T 2150-2010 光缆分纤箱

本标准规定了光缆分纤箱的定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于露天、楼道、室内等场所使用的光缆分纤箱。

Optical fiber cable distribution box

DS/EN 62343-3-1:2010 动态模块 第 3-1 部分：性能规范模板 动态信道均衡器

IEC 62343-3-1:2010 provides a performance specification template for the dynamic channel equalizer (DCE). The object of this performance specification template is to provide a frame for the preparation of detail specifications on the performances of dynamic channel equalizers. Additional specification parameters may be included for detailed product specifications or performance specifications. However, specification parameters specified in this standard should not be removed from the detail product specifications or performance specifications.

Dynamic modules - Part 3-1: Performance specification templates - Dynamic channel equalizers

DS/IEC/TR 62343-6-3:2010 动态模块 第 6-3 部分：可调谐色散补偿器群延迟纹波的循环测量结果

This technical report describes the round robin measurement results for the group delay ripple (GDR)of tunable dispersion compensators (TDCs). It briefly explains the four typical TDCs measured and fourtypical methods of measuring group delay (GD), as well as the GDR round robin measurement resultsof TDCs, and an analysis of repeatability and differences among these measurement methods. Thisdocument also proposes suitable measurement parameters and a new parameter of phase rippleinstead of GDR.

Dynamic modules - Part 6-3: Round robin measurement results for group delay ripple of tunable dispersion compensators

IEC PAS 61753-088-2:2010 光纤互连器件和无源元件性能标准.第088-2部分:带有800 GHz信道间隔的C类非连接式单模光纤局域网波分多路复用设备(LAN WDM).可控环境

This Publicly Available Specification (PAS) contains the minimum initial test and measurement requirements and severities which a non-connectorised single-mode fibre optic Local Area Network Wavelength Division Multiplexing (LAN WDM) device with channel spacing of 800 GHz needs to satisfy in order to be categorised as meeting the requirements of category C – Controlled environments, as defined in Annex A of IEC 61753-1. The applications of LAN WDM adevices are optical MUX and DEMUX for 100GBASE-LR4 (required operating range of 2 m to 10 km) and 100GBASE-ER4 (required operating range of 2 m to 30 km) defined in IEEE Draft P802.3ba, as shown in Annex D. The requirements cover both an integrated 1 × 4 LAN WDM device and an individual 1 × 2 LAN WDM device for cascaded module construction.

Fibre optic interconnecting devices and passive components performance standard - Part 088-2: Non-connected single-mode fibre optic LAN WDM devices with channel spacing of 800 GHz for category C - Controlled environments

DS/EN 62343-5-1:2010 动态模块 测试方法 第 5-1 部分：动态增益倾斜均衡器 响应时间测量

1.1 ScopeThis part of IEC 62343 contains the measurement method of response time for a dynamic gain tilt equalizer (DGTE) to change its gain tilt from an arbitrary initial value to a desired target value.

Dynamic modules - Test methods - Part 5-1: Dynamic gain tilt equalizer - Response time measurement

BS EN 62134-1:2009 光纤互连设备和无源元件.光纤外封壳体.一般规范

This part of IEC 62134 establishes uniform generic requirements for fibre optic closures. This standard does not cover test and measurement procedures, which are described in IEC 61300 series.

Fibre optic interconnecting devices and passive components - Fibre optic closures - Generic specification

LST EN 62134-1-2010 光纤互连设备和无源元件 光纤闭合 第1部分：通用规范（IEC 62134-1:2009）

Fibre optic interconnecting devices and passive components - Fibre optic closures - Part 1: Generic specification (IEC 62134-1:2009)

IEC 61746-1:2009 光时域反射计(OTDRs)的校准.第1部分:单模光纤用光时域反射计

Calibration of optical time-domain reflectometers (OTDR) - Part 1: OTDR for single-mode fibres

IEC 86B/2968/PAS:2009 IEC/PAS 61753-088-2,版本1:光纤互连装置和无源元件性能标准.第088-2部分:U类800 GHz带有信道间隔的非连接单模光纤局域网(LAN)波分多路复用(WDM)器件.可控环境

IEC/PAS 61753-088-2, Ed. 1: Fibre optic interconnecting devices and passive components performance standard - Part 088-2: Non-connected single-mode fibre optic LAN WDM devices with channel spacing of 800 GHz for category C - Controlled environment

YD/T 925-2009 光缆终端盒

本标准规定了光缆终端盒的分类和命名、要求、试验方法、检验规则和包装、标志、运输和贮存。 本标准适用于室内以及非露天的室外使用的光缆终端盒。

Optical Fibre Cable Terminal Case

DIN 58143-5:2009 光纤产品的数据单规范.第5部分:冷光源

Data sheet specification of fibre optic products - Part 5: Cold light sources

DS/EN 62343-1-2:2008 动态模块 第 1-2 部分：性能标准 用于受控环境的带有尾纤的动态色散补偿器（C 类）

This standard contains the minimum initialisation test and measurement requirements and severities, which an optical dynamic chromatic dispersion compensator (DCDC) shall satisfy in order to be categorised as meeting the requirements of DCDC used in controlled environments. The requirements cover optical dynamic chromatic dispersion compensators for Category C – Controlled environments.

Dynamic modules - Part 1-2: Performance standards - Dynamic chromatic dispersion compensator with pigtails for use in controlled environments (Category C)

YD/T 1766-2008 光通信用光收发合一模块的可靠性实验失效判据

本标准规定了光通信用光收发合一模块可靠性实验的分类、实验条件、实验方法和失效判据等。 本标准适用于155Mbit/s、622Mbit/s、1.25Gbit/s、2.5Gbit/s和10Gbit/s等不同速率的光通信用光收发合一模块（包括波长可调光收发合一模块），其他速率的光收发合一模块可参照执行。

Failure Criteria of Reliability Tests for Optical Transceiver/Transponder Used in Optical Communications

ANSI/INCITS 437-2008 信息技术.光纤通道SATA通道协议(FC-SATA)

Information technology - Fibre Channel SATA Tunneling Protocol (FC-SATA)

BS PD CLC/TR 50510:2007 用户终端的纤维光学通路.FTTX纤维光学网络的建设指南

This Technical Report describes the FTTX-network. As a guideline other parts of the fibre optic infrastructure are given in this clause. First some basics: sound, pictures, voice, data carried by networks are digital data expressed in terms of bit, bytes and their multiples (kilo (k), mega (M), giga (G), tera (T)). A bit (binary digit) is the smallest digital unit and has only two values: 0 or 1. A byte includes 8 bits and defines the size of a data file. Transmission capacity of networks and terminals is not expressed by using bytes, but using bit per second (bps). When a data file is transferred in a network two supplementary bits are necessary. It means that 10 bits are required for 1 byte. In the case of a VDSL subscriber with 10 Mbit/s, who wants to upload a pdf data file, the Web provider indicates for instance the following size: 20 Megabytes. It should then take 20 s. However, for any Mbit/s subscription the fact is that the real final data flow is about a quarter of the notified data flow, because the data flow is shared between subscribers and its quality depends on the activity of the other subscribers. It means that the 20 Megabytes data file will need 1 min 20 s to be uploaded. For instance a 15 Mbit/s ADSL system gives only 1 Mbit/s for uploading. The following table gives some further examples of transmission times for uploading a quality DVD-movie, if there is no data flow sharing. We do not know the new tools that will be created by the real high bit rate networks. New applications (not invented today) will appear and applications originally dedicated to professionals will be extended to all in a similar way as it happened with the mobile phone. It is important to define the meaning of « low, medium and high bit rate transmission ». One possible classification is presently the following: − low bit rate transmission: up to 1 Mbit/s − medium bit rate transmission: 1 up to 10 Mbit/s − high bit rate transmission: 10 up to 100 Mbit/s and more.

Fibre optic access to end-user — A guideline to building of FTTX fibre optic network

YD/T 1617.1-2007 智能化光保护系统 第1部分:光线路保护系统

本部分规定了光线路保护系统的术语和定义、通用管理功能要求、系统硬件要求、试验方法、检验规则、标志、包装、运输和贮存。 本部分适用于智能化的光线路保护系统。

Intelligent optical protect system Part 1: optical line protection system

YD/T 988-2007 通信光缆交接箱

本标准规定了通信光缆交接箱（以下简称OCC）产品的定义、结构、型式、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于通信光缆交接箱。

Cross Connecting Cabinet for Communication Optical Cable

YD/T 814.4-2007 光缆接头盒 第4部分:微型光缆接头盒

本部分规定了微型光缆接头盒（以下简称接头盒）的术语和定义、分类和命名、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本部分适用于通信用气吹微型光缆安装使用的光缆接头盒。

Closure for optical fibre cables Part 4: closure for microduct optical fibre cables

DIN EN 61315:2006 光纤功率表标定（IEC 61315: 2005）; 德文版本 EN 61315: 2006

This international standard is applicable to instruments measuring radiant power emitted from sources which are typical for the fibre-optic communications industry. These sources include laser diodes, light emitting diodes (LEDs) and fibre-type sources. The radiation may be divergent or collimated. The standard describes the calibration of power meters to be performed by calibration laboratories or by power meter manufacturers.#,,#

Calibration of fibre-optic power meters (IEC 61315:2005); German version EN 61315:2006