相纸、胶卷和暗盒标准-分析测试百科网

ASTM E2246-11(2018) 使用光学干涉仪的薄的反射膜的应变梯度测量的标准测试方法

1.1 This test method covers a procedure for measuring the strain gradient in thin, reflecting films. It applies only to films, such as found in microelectromechanical systems (MEMS) materials, which can be imaged using an optical interferometer, also called an interferometric microscope. Measurements from cantilevers that are touching the underlying layer are not accepted. 1.2 This test method uses a non-contact optical interferometric microscope with the capability of obtaining topographical 3-D data sets. It is performed in the laboratory. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Strain Gradient Measurements of Thin, Reflecting Films Using an Optical Interferometer

ICS: 37.040.20
CCS
发布: 2018-05-01
实施

ISO 18944:2018 成像材料.反射彩色摄影照片.测试打印结构和测量

This document specifies requirements and recommendations for the digital test file content, printer setups and printing procedures that are used to generate target prints for test method standards and specifications for image stability in the context of reflection colour photographic prints. Furthermore, this document defines measurement procedures of the test patches as well as how changes of colour attributes are calculated in the course of a given image stability test. Definition of the statistical procedure for data reduction and the translation of those changes into psychophysical end point levels does not belong to the scope of this document, but results obtained with the methods defined in this document can feed into the appropriate statistical evaluation and end point systems of a print life specification defined in other documents.

Imaging materials - Reflection colour photographic prints - Test print construction and measurement

ICS: 37.040.20
CCS: G81
发布: 2018-05-01
实施

ASTM E2245-11(2018) 使用光学干涉仪的薄的反射膜的残余应变测量的标准测试方法

1.1 This test method covers a procedure for measuring the compressive residual strain in thin films. It applies only to films, such as found in microelectromechanical systems (MEMS) materials, which can be imaged using an optical interferometer, also called an interferometric microscope. Measurements from fixed-fixed beams that are touching the underlying layer are not accepted. 1.2 This test method uses a non-contact optical interferometric microscope with the capability of obtaining topographical 3-D data sets. It is performed in the laboratory. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Residual Strain Measurements of Thin, Reflecting Films Using an Optical Interferometer

ICS: 37.040.20
CCS
发布: 2018-05-01
实施

HG/T 5311-2018 印刷用柔性树脂版

Flexible resin plate for printing

ICS: 37.040.20
CCS: G80
发布: 2018-04-30
实施: 2018-09-01

HG/T 5306-2018 医用胶片打印机

Medical film printer

ICS: 37.040.20
CCS: G81
发布: 2018-04-30
实施: 2018-09-01

HG/T 5143-2017 山嵛酸纯度的测定气相色谱法

Determination of behenic acid purity by gas chromatography

ICS: 37.040.20
CCS: G80
发布: 2017-07-07
实施: 2018-01-01

ISO 18941:2017 成像材料.彩色反射印刷.臭氧气体褪色稳定性的试验方法

Imaging materials - Colour reflection prints - Test method for ozone gas fading stability

ICS: 37.040.20
CCS: G81
发布: 2017-07-01
实施

HG/T 5144-2017 纳米无砂目喷墨计算机直接制版(CTP)版材

本标准规定了纳米无砂目喷墨计算机直接制版(CTP)版材的技术要求，检验方法，检验规则，包装、标志、贮存和运输以及保证期。本标准适用于除油的纯铝、金属合金、耐高温树脂或者特殊纸张等为支持体的带喷墨打印纳米亲水层的无砂目喷墨计算机直接制版(CTP)版材。

Nano no graining inkjet CTP plate

ICS: 37.040.20
CCS: G80
发布: 2017-04-12
实施: 2017-10-01

HG/T 4127-2017 医用干式胶片

本标准规定了医用干式胶片的要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于经过计算机处理后以数字方式存储的医疗影像热敏打印输出使用的胶片。

Medical dry imaging film

ICS: 37.040.20
CCS: G80
发布: 2017-04-12
实施: 2017-10-01

GSO ISO 6148:2016 摄影缩微胶片、线轴和芯尺寸

This International Standard provides specifications for — dimensions (thickness, width, length) of raw stock roll and sheet films for micrographic applications, including silver-gelatin, diazo, and vesicular films, designed for document recording, computer output microfilming (COM), and duplicating or printing. These products require wet chemical, vapour, or heat processing after an image-forming exposure with actinic radiation; — winding requirements for roll films; — location and width of the heading area for 105 mm wide rolls and sheets, and the width and thickness of the backing of that area; — dimensions of spools, made either of metal or plastic, for 16 mm, 35 mm, and 105 mm microfilms; other spool materials are excluded, as well as spools that are integral components of cartridges, cassettes or magazines of microfilm-recording equipment; — dimensions of plastic and metal cores of 16 mm, 35 mm, and 105 mm widths. Dimensions for thin-walled paper-board cores with wall thickness of 7,6 mm or less, used routinely for sensitized duplicating material, are not included in this International Standard. This International Standard is not applicable to processed-film dimensions in micrographic applications.

Photography -- Micrographic films, spools and cores -- Dimensions