43.040.20 照明、信号和警告设备 标准查询与下载
共找到 651 条与 照明、信号和警告设备 相关的标准，共 44 页
This SAE Recommended Practice provides dimensional specifications for the 4 1/2 and 5 3/4 inch general service sealed lighting units, intended for use in such applications as motorcycle headlamps, military headlamps, industrial machinery headlamps, fog lamps, spot lamps, etc. This document supersedes SAE J 760.
Dimensional Specifications for General Service Sealed Lighting Units
- ICS
- 43.040.20
- CCS
- 发布
- 2013-06-10
- 实施
- 2017-11-18
Lamps for road vehicles - Dimensional, electrical and luminous requirements (IEC 60809:1995 + A1:1996 + A2:2002 + A3:2004 + A4:2009 + A5:2012); German version EN 60809:1996 + A1:1996 + A2:2002 + A3:2004 + A4:2009 + A5:2012
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2013-06
- 实施
- 2013-06-01
This SAE Recommended Practice provides standardized laboratory tests, test methods, and performance requirements applicable to lighting devices and components used on vehicles 2032 mm or more in overall width.
Test for Signal and Marking Devices Used on Vehicles 2032 mm or more in Overall Width
- ICS
- 43.040.20
- CCS
- T04
- 发布
- 2013-04-09
- 实施
- 2014-12-04
defines the acceptable quality levels for each characteristic checked when samples of flashers for power-driven vehicles (with the exception of motorcyclesl)) are taken at random. This International Standard does not specify the frequency of sampling, nor the batch size.
Road vehicles -- Motor vehicles -- Production conformity requirements for flasher units
- ICS
- 43.040.20
- CCS
- 发布
- 2013-04-01
- 实施
Abstract Defines the electrical characteristics with which flasher units shall comply when submitted for acceptance. Applies to flashers intended for use on motor vehicles with 12 V or 24 V systems, which may or may not be equipped for a towed vehicle. Can be applied to motorcycles. Not applicable to two-level luminous intensity devices.
Road vehicles -- Motor vehicles -- Flasher units
- ICS
- 43.040.20
- CCS
- 发布
- 2013-04-01
- 实施
specifies the provisions applicable to retro-reflective registration plates for motor vehicles and their trailers.
Road vehicles -- Retro-reflective registration plates for motor vehicles and trailers -- Specification
- ICS
- 43.040.20
- CCS
- 发布
- 2013-04-01
- 实施
specifies the dimensions of special warning lamps for road vehicles, in order to ensure interchangeability and accurate positioning, bearing in mind the rapid change of light intensity from such devices in a vertical cross-section of the projected beam.
Road vehicles -- Special warning lamps -- Dimensions
- ICS
- 43.040.20
- CCS
- 发布
- 2013-04-01
- 实施
For lighting and light signalling devices to be installed into road motor vehicles and their trailers. This document shall be applied when no other detailed specifications are available to choose the requirements for the appropriate devices regarding their design data and installation
Road vehicles -- Legal situation concerning lighting and light-signalling devices
- ICS
- 43.040.20
- CCS
- 发布
- 2013-04-01
- 实施
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
Highly Accelerated Failure Test (HAFT) for Automotive Lamps with LED Assembly
- ICS
- 43.040.20
- CCS
- T36
- 发布
- 2013-03-26
- 实施
- 2018-05-29
This SAE Standard provides test procedures, requirements, and guidelines for a Front Position lamp.
Front Position Lamp
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2013-03-05
- 实施
- 2013-03-07
This SAE Standard provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies. Lamps can be evaluated using the method described in SAE J 3333; however, no lamp is subjected to both methods.
Determination of the Effective Projected Luminous Lens Area (EPLLA) by Design Analysis
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2013-03-05
- 实施
- 2017-06-13
Lamps for road vehicles - Dimensional, electrical and luminous requirements
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2013-02-09
- 实施
- 2013-02-09
This document is a general level subsystem light source specification that establishes test requirements of Light Emitting Diode (LED) components and modules for use in automotive lighting systems. The completed test data to this test specification is intended to be provided to the OEM by the Tier I lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved LED modules experiences a design, manufacturing or component change. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. The LED module is defined as the LED dev
Specification for Testing Automotive LED Modules
- ICS
- 43.040.20
- CCS
- T36
- 发布
- 2013-02
- 实施
Road vehicles－Headlamp cleaners
- ICS
- 43.040.20
- CCS
- 发布
- 20121130
- 实施
- 20121130
Road vehicles－Sound signalling devices－Technical specifications
- ICS
- 43.040.20
- CCS
- 发布
- 20121130
- 实施
- 20121130
Road vehicles－Sound signalling devices－Technical specifications
- ICS
- 43.040.20
- CCS
- 发布
- 2012-11-30
- 实施
This SAE Recommended Practice is intended as a guide toward standard and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements, design requirements and design guidelines for electronic devices.
Application Guidelines for Electronically Driven and/or Controlled Exterior Automotive Lighting Equipment
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2012-11-01
- 实施
- 2012-11-03
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice provides laboratory test procedures, requirements and guidelines for electronic siren systems with a single loudspeaker, and electromechanical sirens for use on authorized emergency vehicles, which call for the right-of-way. Test procedures and performance requirements for individual system components are not included in this version. Results obtained for a siren system with a speaker array that
Emergency Vehicle Sirens
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2012-10-15
- 实施
- 2013-09-13
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines - Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
Lighting and Marking of Construction, Earthmoving Machinery
- ICS
- 43.040.20
- CCS
- P97
- 发布
- 2012-10-09
- 实施
