43.040.60 车身及车身附件 标准查询与下载

T/QGCML 779-2023 发动机盖支撑杆

本文件规定了发动机盖支撑杆的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于发动机盖支撑杆的生产和检验。

engine cover support rod

T/CAAMTB 118-2023 乘用车外包围改装指南

本文件规定了乘用车外包围改装的技术要求、评估检查方法、其他要求。 本文件适用于乘用车外包围改装。

Passenger car exterior surround modification guide

T/CAAMTB 116-2023 汽车车门锁扣性能要求和试验方法

本文件规定了汽车车门锁扣相关的术语和定义、性能要求、试验方法、检验规则和标志、包装、运输和储存要求。 本文件适用于M1和N1类车辆的侧门、后门或行李箱的锁扣。

Performance requirements and test methods for automobile door latch

BS ISO 11154:2023 公路车辆 屋顶承重车

1   Scope This document applies for roof racks of passenger cars and light commercial vehicles up to a permissible total weight of 3,5 t according to ISO 1176 and specifies requirements and test methods for these. It is also valid for roof racks mounted on trailers. So-called magnetic or suction foot racks, i.e. roof racks whose attachment on the vehicle is only via magnetic forces or vacuum, are excluded from this document. This document provides safety-related requirements under consideration of the weight, centre of gravity, air resistance and other safety-relevant properties for structures of roof racks for which no other technical or statutory regulations otherwise apply and which are not listed in 4.2. In individual cases, test requirements can extend beyond these requirements.

Road vehicles. Roof load carriers

T/CASME 341-2023 高可靠性自动防眩目内后视镜

本文件规定了高可靠性自动防眩目内后视镜的技术要求、试验方法、检验规则、标志、包装、运输和贮存。

High reliability automatic anti-glare interior rearview mirror

ISO 11154:2023 道路车辆.车顶承载架

This document applies for roof racks of passenger cars and light commercial vehicles up to a permissible total weight of 3,5 t according to ISO 1176 and specifies requirements and test methods for these. It is also valid for roof racks mounted on trailers. So-called magnetic or suction foot racks, i.e. roof racks whose attachment on the vehicle is only via magnetic forces or vacuum, are excluded from this document. This document provides safety-related requirements under consideration of the weight, centre of gravity, air resistance and other safety-relevant properties for structures of roof racks for which no other technical or statutory regulations otherwise apply and which are not listed in 4.2. In individual cases, test requirements can extend beyond these requirements.

Road vehicles — Roof load carriers

T/CIPR 004-2023 车厢底板

本文件规定了车厢底板的技术要求、试验方法、检验规则和运输。 本文件适用于道路运输的车厢底板。

Carriage floor

ASTM D6675-23 汽车钢板上有机涂层的盐加速室外外观腐蚀试验的标准实施规程

1.1 This practice is designed to assist procedures to be followed when conducting outdoor exposures to evaluate cosmetic corrosion that might occur in steel panels covered with an organic coating that has been damaged. The outdoor exposures described are based on Practices G7 and G50 and include periodic wetting of the test specimens with a salt solution. 1.2 The methods of preparing test specimens and the particular exposure requirements of materials are beyond the scope of this practice. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel

JT/T 305-2023 客车电动换气扇

本标准适用于客车用电动换气扇的生产和检验。

Passenger car electric ventilation fan

KS R 4060-2022 汽车悬架支柱

Suspension struts for automobiles

T/ZZB 2838-2022 乘用车玻璃升降器导轨

本文件规定了乘用车玻璃升降器导轨的术语和定义、结构型式、基本要求、技术要求、试验方法、检验规则、标识、包装、运输和贮存、质量承诺。 本文件适用于乘用车玻璃升降器铝制导轨（以下简称导轨）。

Passenger car window regulator guide rails

T/ZS 0383-2022 汽车用纺织防滑链

前言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本要求　 5 技术要求　 6 试验方法　 7 检验规则　 8 标志、包装、运输与贮存　

Textile anti-skid chains for automobiles

T/ZPP 031-2022 车用尾气处理尿素软管技术要求

本文件规定了柴油车SCR 系统中输送车用尿素溶液的ID4和ID5.5软管的结构，技术要求，试验方 法，标志，检验、包装、运输及贮存。  本文件适用于生产车用尾气处理尿素软管的企业。

Technical requirements for urea hoses for vehicle exhaust gas treatment

T/JX 052-2022 汽车模型内饰设计指南

本文件给出了汽车模型内饰（以下简称模型）的设计指南，包括模型骨架设计、各模块结构设计、常用标准件要求及常用材料规格要求。 本文件适用于汽车模型内饰的设计。

Model Car Interior Design Guidelines

T/QGCML 405-2022 智能雨刷控制器

本文件规定了智能雨刷控制器的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于智能雨刷控制器的生产和检验。

Smart wiper controller

T/CAS 599-2022 汽车空调制冷剂（HFC-134a）泄漏测试方法及限值

1　范围 本标准规定了汽车空调系统制冷剂（HFC-134a）泄漏测试的试验设备、预处理及采样、测定及结果计算、泄漏限值、试验报告的要求。 本标准适用于M1、N1类车辆汽车空调制冷剂(HFC-134a)的采样和测定，其他类型车辆汽车空调及制冷剂可参照执行。 2　规范性引用文件 下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件，仅注日期的版本适用于本文件。凡是不注日期引用文件，其最新版本（包括所有的修改单）适用于本文件。 QC/T 720—2004  汽车空调术语 3　术语和定义 QC/T 720—2004界定的以及下列术语和定义适用于本文件。 3.1　 汽车空调 automobile air conditioning 由压缩机、冷凝器、节流元件、蒸发器、制冷剂管路、风机及必要的控制部件等构成，用于调节空气的温度、湿度，给汽车乘员及关键部件提供适宜环境的空调系统。 注1：按照功能可分为单冷型、制冷电热型、热泵型、电热辅助热泵型、水暖辅助热泵型。 注2：本标准中用于泄漏测试的汽车空调由压缩机、冷凝器、节流元件、蒸发器、制冷剂管路等所有直接流经制冷剂的零部件构成，不包含空调箱、风机等不直接接触制冷剂的零部件。 [来源：GB/T 21361—2017，3.1，有修改] 3.2　 制冷剂 refrigerant 在汽车空调中用于传递热量的流体，在低温低压环境吸收热量，在高温高压环境释放热量，通常伴有相变过程。 [来源：HJ 1195—2021，3.1，有修改]

Test methods and limits of refrigerant (HFC-134a) leakage in automobile air conditioning

KS R 0015-2022 汽车零部件受潮、淋雨、喷雾试验方法

Method of moisture, rain and spray test for automobile parts

KS R ISO 5740-2022 乘用车 后视镜 反射率测定试验方法

Passenger cars－Rear view mirrors－Test method for determining reflectance

KS R ISO 5898-2022 乘用车 后窗除霜系统 试验方法

Passenger cars－Rear－window defrosting system－Test method

KS R 3022-2022 工业车辆和越野服务的轮辋轮廓

Contours of Rims for Industrial Vehicles and Off the Road Service