43.040.65 玻璃窗和刮水器 标准查询与下载

NF R14-601:2000 道路车辆.刚性塑料安全玻璃材料试验

Road vehicles - Tests for rigid plastic safety glazing materials.

NF R14-602:2000 道路车辆.安全玻璃材料.机械试验

Road vehicles - Safety glazing materials - Mechanical tests.

DIN 72786-3:2000 公路车辆的挡风刮水器系统.弧刷臂.第3部分:刮水器杆材料

The following items are covered: Dimensions, materials, finish and supply conditions.

Windscreen wiper systems for road vehicles - Wiper arm - Part 3: Wiper rod material

SAE J381-2000 （R）挡风玻璃除霜系统测试程序和性能要求 卡车、公共汽车和多用途车辆

This SAE Recommended Practice establishes uniform test procedures for the defrosting systems of enclosed cab trucks, buses, and multipurpose vehicles. It is limited to tests that can be conducted on uniform test equipment in commercially available laboratory facilities. Current engineering practice prescribes that for laboratory evaluation of defroster systems, an ice coating of known thickness be applied to the windshield and left- and right-hand side windows to provide more uniform and repeatable test results, even though under actual conditions such a coating would necessarily be scraped off before driving. The test condition, therefore, represents a more severe condition than the actual condition, where the defroster system must merely be capable of maintaining a cleared viewing area. Because of the special nature of the operation of most of these vehicles (where vehicles are generally warmed up before or garaged in preparation for road operations) and since defrosting under steady-state, over-the-road operations is the main concern, test conditions have been adopted which eliminate the engine warm-up phase of vehicle operation. This document will be reviewed and revised as technological progress in vehicle defroster test procedure requires.

(R) Windshield Defrosting Systems Test Procedure and Performance Requirements - Trucks, Buses, and Multipurpose Vehicles

SAE J1944-2000 卡车和公共汽车多功能车辆挡风玻璃喷洗器系统

This SAE Recommended Practice provides the following for the windshield washer system for trucks, buses, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or greater: a.) Minimum performance requirement; b.) Uniform test procedures. The test procedures are limited to those tests that can be conducted with uniform test equipment by commercially available laboratory facilities; and c.) Uniform terminology of windshield washer system characteristics and phenomena. the minimum performance requirements and test procedures, outlined in this document, are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised as additional data on windshield washer system performance are developed.

Truck and Bus Multipurpose Vehicle Windshield Washer System

ISO 3917:1999 道路车辆 安全玻璃材料 耐辐射、耐高温、耐湿度、耐燃烧和耐模拟气候的试验方法

This International Standard specifies test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering, relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or the material of which they are composed.

Road vehicles - Safety glazing materials - Test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering

ISO 15082:1999 道路车辆 刚性塑料安全玻璃材料的试验

This International Standard specifies all test methods relating to the safety requirements for rigid plastic safety glazing materials in a road vehicle, regardless of the type of plastic of which they are composed. NOTE Plastic safety glazing materials are classified as rigid or flexible by use of the test described in annex A.

Road vehicles - Tests for rigid plastic safety glazing materials

SAE J216-1999 （R）机动车玻璃 电路

This SAE Recommended Practice establishes limits for electrical circuits on motor vehicle safety glazing materials.

(R) Motor Vehicle Glazing - Electrical Circuits

ISO 3537:1999 道路车辆 安全玻璃材料 力学性能试验

This International Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.

Road vehicles - Safety glazing materials - Mechanical tests

DIN 52298-1:1998 道路车辆.汽车安全玻璃光散射测定.第1部分:环形孔板法

Road vehicles - Measurement of scattered light of safety glazing materials for vehicle glazing - Part 1: Annular diaphragm method

DIN 52289:1998 道路车辆.汽车安全玻璃.耐化学性试验

This document describes methods for the determination of chemical resistance of plastics, glasses coated with plastics and lamination of glass and plastics with an uncovered plastic-surface which is used as safety glazing material for road vehicles.#,,#

Road vehicles - Safety glazing materials - Determination of the chemical resistance

ISO 5897:1998 乘用车 后车窗除雾系统 试验方法

This International Standard specifies a test method for passenger car (as defined in ISO 3833) rear-window demisting systems, when these are fitted. It does not specify reference areas or levels of performance, since at the time it was prepared there was insufficient data available. NOTE — It may be possible to carry out tests of a similar nature on windscreen and rear-window simultaneously. The test method is intended for types of power-driven vehicles which do not differ from one another with respect to the following essential features which affect demisting performance: a) shape, size and surface characteristics of the rear-window; b) characteristics of each system designated by the vehicle manufacturer as contributing to the demisting of the rear-window; c) number of seats as designated by the vehicle manufacturer.

Passenger cars - Rear-window demisting system - Test method

SAE J964-1998 测量镜面雾度和反射率的推荐做法

This SAE Recommended Practice describes methods for determining total and specular reflectance for mirrors with flat and curved surfaces and a method for determining diffuse reflectance and haze for mirrors with flat surfaces.

Recommended Practice for Measuring Haze and Reflectance of Mirrors

DIN 72783:1997 汽车挡风玻璃刮水器.滚花锥固定装置

The document applies to knurled tapered shaft ends used at windscreen wiper systems and rear opening wiper system, being used to fasten the wiper arm and motor lever respectively. The standard contains those dimensions being required for interchangeability.#,,#

Windscreen wiper systems for road vehicles - Tapered knurled shaft ends and matching holes

ISO 5898:1997 乘用车 后车窗除霜系统 试验方法

This International Standard specifies a test method for passenger car (as defined in ISO 3833) rear-window defrosting systems, when these are fitted. It does not specify reference areas or levels of performance, since at the time it was prepared there was insufficient data available. NOTE — It may be possible to carry out tests of a similar nature on windscreen and rear-window simultaneously. The test method is intended to apply to types of power-driven vehicles which do not differ from one another in respect of the following essential features which affect defrosting performance: a) shape, size and surface characteristics of the rear-window; b) characteristics of each system designated by the vehicle manufacturer as contributing to the defrosting of the rear-window.

Passenger cars - Rear-window defrosting system - Test method

ISO 6255:1997 乘用车 乘用车后窗洗涤和刮刷系统 试验方法

This International Standard specifies test methods for passenger car (as defined in ISO 3833) rear-window washing and wiping systems, when these are fitted, excluding convertible passenger cars with rear-windows made of plastic. This International Standard does not specify reference areas or levels of performance, since at the time it was prepared there was sufficient data available. NOTE — It may be possible to carry out tests of a similar nature on windscreen and rear-window simultaneously. The test methods are intended to apply to types of power-driven vehicles which do not differ from one another in respect of the following essential features which affect washing and wiping performance: a) shape, size and surface characteristics of the rear-window; b) characteristics of each system designated by the vehicle manufacturer as contributing to the washing and wiping of the rear-window.

Passenger cars - Rear-window washing and wiping systems - Test methods

SAE J674-1997 安全玻璃材料机动车辆和机动车辆设备

All glazing materials used in motor vehicles and motor vehicle equipment operating on land highways should comply with the requirements of the American national Standard, ANSI/SAE Z-26.1. The American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways-Safety Code, ANSI/SAE Z-26.1-1990 is the latest complete updated version and is referred to hereafter as the safety code. This SAE Recommended Practice is not intended to preclude references to any governmental law, ordianance, or regulation which might apply to the glazing of motor vehicles and motor vehicle equipment operating on land highways.

Safety Glazing Materials Motor Vehicles and Motor Vehicle Equipment

SAE J1556-1997 固定式安全玻璃更换

This SAE Recommended Practice provides guidelines for automotive vehicle glass replacement shops and their personnel in the correct replacement practices, materials, and procedures for stationary safety glazing components. The design of today's automotive vehicles and the development of new technology can directly influence occupant safety and vehicle structural integrity. The correct installation of stationary safety glazing components can contribute directly to occupant safety and structural integrity of the vehicle.

Stationary Safety Glazing Replacement

ISO 3538:1997 道路车辆 安全玻璃材料 光学性能试验方法

This International Standard specifies optical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.

Road vehicles - Safety glazing materials - Test methods for optical properties

SAE J1535-1996 野外自行式作业机器挡风除霜系统的性能试验

This SAE Standard establishes uniform test procedures for the defrosting systems of off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, forestry, and specialized mining machinery categories as identified in SAE J1116, JUN86. It includes tests that can be conducted with uniform test equipment in commercially available laboratory facilities, as well as in an appropriate outdoor environment.

Performance Test for Windshield Defrosting Systems for off-Road, Self- Propelled Work Machines