共找到 225 条与 联轴器 相关的标准,共 15 页
1 Scope This International Standard defines different multiple-vehicle combinations (vehicle combinations with more than one coupling point) and the formulae to calculate the requirement of performance for the coupling equipment used in those vehicle combinations. Vehicle categories concerned are N2, N3, O3, and O4. NOTE For these vehicle combinations, the formulae in this International Standard override the formulae in References [6], [7], [8], and [9] that apply to vehicle combinations with one coupling point only. However, the capability of the coupling equipment is still determined through tests as defined in References [6], [7], [8], and [9].
Commercial road vehicles. Coupling equipment between vehicles in multiple vehicle combinations. Strength requirements
This document specifies the characteristics necessary for the mounting and interchangeability of clevis couplings on the frame (cross member, drawbeam or mounting bracket) of towing vehicles for trailers. This document is applicable to clevis couplings intended for connection to trailers equipped with a drawbar eye on the drawbar of the trailer. Characteristics not specified are left to the discretion of the component manufacturer.
Road vehicles — Clevis couplings — Interchangeability
Commercial road vehicles — Coupling equipment between vehicles in multiple vehicle combinations — Strength requirements — Amendment 1: Clarification for calculation for V-value for combinations includ
Commercial road vehicles — 50 mm drawbar eye — Interchangeability
Road vehicles — Drawbar couplings — Interchangeability
Road vehicles-Towing vehicle coupling device to tow caravans or light trailers-Mechanical strength test
Road vehicles?Coupling balls for caravans and light trailers?Dimensions
Road vehicles?Coupling balls for caravans and light trailers?Dimensions
Road vehicles-Towing vehicle coupling device to tow caravans or light trailers-Mechanical strength test
Road vehicles ? Coupling balls for caravans and light trailers ? Dimensions
Road vehicles-Towing vehicle coupling device to tow caravans or light trailers-Mechanical strength test
This International Standard gives a simplified procedure for the calculation of the mechanical strength of steel drawbars, whether there are welds or not, for centre-axle trailers Categories O1 and O2 as specified in the UNECE, Consolidated Resolution on the Construction of Vehicles (R.E.3). Consequently, it only applies to simple constructions that enable a calculation in bending.
Road vehicles -- Trailers up to 3,5 t -- Calculation of the mechanical strength of steel drawbars
This part of ISO 9367 specifies the minimum requirements to allow efficient lashing and securing of semi-trailers, as defined in ISO 3833, on board roll-on/roll-off (Ro/Ro) ships, indicating in particular the lashing arrangements on the semi-trailer and the securing method to be used. It also gives, in annex A, for information to semi-trailer designers, the securing point arrangements generally used on Ro/Ro ships as laid down by International Maritime Organization (IMO) recommendations. In annex B, it gives for information some design indications to decrease damage during handling.
Lashing and securing arrangements on road vehicles for sea transportation on Ro/Ro ships -- General requirements -- Part 2: Semi-trailers
This International Standard specifies the characteristics of the towing anchorages mounted on road vehicles, allowing them to be towed or to tow another vehicle by means of towing ropes, cables or bars at the vehicle manufacturer's option.
Road vehicles -- Anchorages for towing ropes, cables or bars
Road vehicles-Mechanical coupling between tractor and semi -trailers-Interchangeability
Scope is not provided for this standard
Road vehicles -- Fully automatic coupling systems 24 V (FACS) for heavy commercial vehicle combinations -- Part 2: 50 mm fifth wheel couplings -- Electrical and pneumatic interface
Scope is not provided for this standard
Road vehicles -- Drawbar couplings, drawbar eyes, fifth wheel kingpins, hook couplings and toroidal eyes -- Wear limits for in-use mechanical couplings
Scope is not provided for this standard
Road vehicles -- 24 V fully automatic coupling systems (FACS) for heavy commercial vehicle combinations -- Part 1: General requirements and definitions
이 표준은 트레일러를 견인하는 차량의 프레임(크로스 멤버, 드로빔 또는 부착용 브래킷)에 대하여 드로바 커플링의 부착과 호환성에 필요한 특성에 대하여 규정한다.이 표준은 트레일러의 드로바에 드로바 아이가 설치된 트레일러에 연결하기 위하여 만든 드로바 커플링에 적용한다.규정하지 않은 특성은 부품 제작사가 정한 바에 따른다.?
Road vehicles — Drawbar couplings — Interchangeability
Road vehicles — Drawbar couplings — Interchangeability
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号