共找到 225 条与 联轴器 相关的标准,共 15 页
이 규격은 한국산업규격(이하, 규격이라 한다.)으로서 캐러밴 또는 경트레일러를 견인하는 견
Road vehicles-Towing vehicle coupling device to tow caravans or light trailers-Mechanical strength test
Specifies the requirements for the selection and marking of pin-type couplings and drawbar eyes and gives the methods for the determination of the D-values and the V-values for typical vehicle configurations.
Commercial road vehicles - Mechanical connections between towing vehicles - Selection and marking of pin-type couplings and drawbar eyes
Provides dimensions for 50 mm pin-type couplings and 50 mm drawbar eyes to permit interchangeability between towing vehicles and trailers fitted with these couplings. This Standard is identical with and has been reproduced from ISO 1102:1986.
Commercial road vehicles - Mechanical connections between towing vehicles - 50 mm pin-type couplings and drawbar eyes
이 규격은 한국산업규격(이하 규격이라 한다.)으로서 트랙터와 세미트레일러 간의 호환성 향상
Road vehicles-Mechanical coupling between tractor and semi -trailers-Interchangeability
Road vehicles-Mechanical coupling between tractor and semi -trailers-Interchangeability
이 규격은 견인차와 경트레일러 혹은 캐러밴 사이를 적절하게 연결하기 위한 장치의 커플링 볼
Road vehicles ? Coupling balls for caravans and light trailers ? Dimensions
This International Standard specifies the requirements for the various elements and dimensions of towing vehicles with rear-mounted coupling and of drawbar trailers, to ensure interchangeability. NOTE Annex B gives examples of different configurations of vehicle combinations; this International Standard deals only with No. B.1.1. This International Standard is applicable to road trains for commercial transport of cargo of the greatest possible variety; it does not cover dedicated or special combinations. Nor does it specify limitations of maximum gross mass and overall dimensions, which are generally laid down by legislative requirements. Vehicles whose couplings form the subject of this International Standard are not interchangeable with vehicles whose couplings are mounted forward and below (which form the subject of ISO 11407 [1]).
Commercial road vehicles - Mechanical coupling between towing vehicles with rear-mounted coupling and drawbar trailers - Interchangeability
This International Standard specifies the dimensional characteristics necessary for the mounting and interchangea-bility of the fifth wheel on the frame (subframe or mounting plate) of towing vehicles for semi-trailers. It is applicable to fifth wheels intended for hitching on semi-trailers equipped with a — 50 kingpin as defined in ISO 337, or — 90 kingpin as defined in ISO 4086. Dimensions not specified are left to the discretion of the component manufacturer. NOTE Those test conditions and strength requirements to be met by 50 and 90 fifth wheel couplings are specified in ISO 8717.
Road vehicles - Fifth wheels - Interchangeability
This International Standard specifies the test conditions and strength requirements to be met by 50 and 90 fifth wheel couplings (see ISO 3842).
Commercial road vehicles - Fifth wheel couplings - Strength tests
Covers requirements for ball type couplings and towing brackets for the towing of caravans and light trailers of gross vehicle mass (GVM) not exceeding 3 500 kg.
Ball type couplings and towing brackets for towing caravans and light trailers
The document contains the following items: damping moment, clearance, operating instructions.
Road vehicles - Stabilizing devices for central-axle trailers - Requirements on effectiveness
Commercial road vehicles - Drawbar couplings and eyes for rigid drawbars - Part 1: Strength tests for general cargo centre-axle trailers
This International Standard specifies the test conditions and strength requirements to be met by drawbar couplings (see ISO 3584) and the corresponding drawbar eyes (see ISO 1102 and ISO 8755) for rigid drawbars, which are provided for use with centre-axle trailers with a technical maximum mass C exceeding 3,5t (tonnes).
Commercial road vehicles - Drawbar couplings and eyes for rigid drawbars - Strength tests
This Korean Industrial Standard specifies hose clamps (hereafter referred to as "clamps") mainly used to connect the hose with the joint or pipes for cooling, suction of air, fuel, lubrication and air- conditioning systems in automobiles.
Hose clamps for automobiles
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
Trailer Couplings, Hitches and Safety Chains Automotive Type
The possible location of hydraulic couplings and their dimensions and requirements shall be specified.
Hydraulic couplings on lorries and semi-trailer towing vehicles - Part 1: Location of hydraulic couplings
Настоящий стандарт распространяется на сцепные шкворни по ГОСТ 12017 и устанавливает технические требования и методы испытаний. Требования
Fifth-wheel king coupling pins of automobile semitrailers. Technical requirements and test methods
Road vehicles. Coupling balls for caravans and light trailers. Dimensions.
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号