43.040.99 其他道路车辆装置 标准查询与下载

NB/T 33024-2016 电动汽车用动力锂离子蓄电池检测规范

Testing specifications for power lithium-ion batteries for electric vehicles

NB/T 33027-2016 电动汽车模块化充电仓技术要求

Technical requirements for modular charging bins for electric vehicles

NB/T 33026-2016 电动汽车模块化电池仓技术要求

Technical requirements for modular battery compartments for electric vehicles

NB/T 33025-2016 电动汽车快速更换电池箱通用要求

General requirements for quick replacement of battery boxes for electric vehicles

DB44/T 1771-2015 分箱式充电机通用技术条件

本标准规定了电动汽车用分箱式充电机（以下简称“充电机”）的使用条件、技术要求、试验方法、标志、包装运输和储存等的要求。 本标准适用于给电动汽车动力蓄电池箱充电的充电机。

General technical specifications for sub-box chargers

DB44/T 1782-2015 风光一体化电动汽车充电站技术要求

本标准规定了由风能、太阳能构成的微网供电系统、电动汽车充电设备及调度管理系统组成的电动汽车充电站的术语、定义、基本参数、技术要求等内容。 本标准适用于分布式电源规模：风力发电100kW以下、光伏发电500kW以下、储能系统500kW/1000kW·h以下，且风光发电功率占充电站充电设备总功率10%以上的风光储微网一体化电动汽车充电站。

Technical requirements for wind-solar integrated electric vehicle charging stations

DB44/T 1760-2015 电动汽车150A三相交流充电接口

本标准规定了电动汽车传导充电用三相交流充电接口的通用要求、功能定义、型式结构、参数和尺寸。 本标准适用于连接方式C的电动汽车传导充电用三相交流充电接口，其额定电压不超过440 V，频率为50Hz，电流范围为63A至150A。 注：连接方式C的定义参见GB/T 20234.1的附录A。

Electric vehicle 150A three-phase AC charging interface

T/ITS 0006-2014 基于OBD的车辆诊断和安防

基于OBD的车辆诊断和安防应用的术语和定义、业务功能、业务实现架构、终端技术要求、应用平台技术要求和终端与平台接口技术要求。

The Standard of vehicle diagnosis and security based on OBD

T/ITS 0009-2014 违法占用公交车专用车道抓拍装备

主要规定了违法占用公交车专用车道车载抓拍装备的术语和定义，功能要求，性能指标，试验方法，检验规则，标志、标签等内容。

The Vehicle-mounted Capture Equipment for Illegal Occupation of Bus-only Lanes

KS I 4004-2014 再制造汽车空调压缩机试验方法

Test methods for remanufactured air-conditioner compressor of automobiles

SAE J191-2014 动力转向压力管-低容积膨胀型

This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications at pressures as indicated in Table 1B, as flexible connections within the temperature range of -40 Ã- C (-40 Ã- F) to 121Ã- C (250 Ã- F) average, 135 Ã- C (275 Ã- F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is not required.

Power Steering Pressure Hose-Low Volumetric Expansion Type

SAE J2884-2014 热固弹性体的规格体系

This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use; recycled; or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum % must be specified using a Z suffix. This classification system covers thermoset High Consistency Elastomers (HCE's) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicon

Thermoset Elastomer Specification System

DB44/T 1189-2013 电动汽车充换电设施电能计量装置技术要求

本标准规定了电动汽车充换电设施电能计量装置的配置安装要求、技术要求、试验方法和检验规则。 本标准适用于电动汽车充换电设施的电能计量。

Technical requirements for electric energy metering devices for electric vehicle charging and swapping facilities

SAE J2287-2012 带有完整搭接和肩带约束的汽车座椅推荐设计和性能标准

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice defines minimum performance standards, qualification requirements, and minimum documentation requirements for Integrated Lap and Shoulder Restraint (to) equipped Seats (IL&SRTS). The goal is to achieve comfort, durability, and occupant protection under expected and foreseeable normal operation loads. The document attempts to define test and evaluation criteria to demonstrated performance at peak operational loads, while attempting to maintain the seats ability to meet loads set forth in FMVSS 207, 210, and ECE 14, 16, and 17. This document also provides guidance for design by enumerating certain design goals to enhance comfort, serviceability, and safety. Guidance for test procedures, measurements, equipment, and interpretation of results may be presented to promote uniform techniques and to achieve acceptable data. While this document addresses system performance, responsibility for the seating systems is divided between the seat supplier and the vehicle OEM. The seat suppliers' responsibility consists of meeting all the established system performance requirements and obtaining and supplying to the vehicle OEM all the data prescribed by this document. The vehicle OEM has the ultimate system responsibility in assuring that all requirements for safe seat applications have been met. This document addresses the static performance criteria for IL&SRTS systems applied to licensed motor vehicles for purposes of transportation.

Recommended Design and Performance Standard for Seats with Integrated Lap and Shoulder Restraints

SAE USCAR7-2012 脆裂性降低验证试验

Deembrittlement verification test

SAE USCAR7-1-2012 去脆化验证测试

Deembrittlement verification test

SAE J189-2012 动力转向回流软管低压

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 degrees C to +120 degrees C (-40 degrees F to +250 degrees F) average, 135 degrees C (275 degrees F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.

Power Steering Return Hose Low Pressure

SAE J190-2012 金属编织动力转向压力软管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers hose fabricated from wire braid and synthetic rubber, assembled with end fittings for use in automotive applications up to 10.3 MPa (1500 psi) maximum pressure, as flexible connections within the temperature range of -40 °C to 121 °C (-40 °F to +250 °F) average, 13.5 °C (275 °F) maximum peaks. The specification in this SAE Standard originated in the SAE-ASTM Technical Committee on Automotive Rubber (other than tires). They represent the correlation of the best information available from research investigation and production experience on the minimum constructional and performance characteristics essential for new power steering assemblies used as original or replacement equipment. This standard applies to passenger cars. It may prove useful to truck manufacturers, but it is not to be presented as present practices. They also represent the minimum quality recognized by original equipment manufacturers and hose suppliers as essential for satisfactory and safe operation by the hose itself and other coacting parts of the power steering system. The original equipment manufacturer may, at his option, add or alter tests through OEM specifications.

Power Steering Pressure Hose - Wire Braid (Stabilized Type)

SAE J188-2012 高容积膨胀型动力转向压力软管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of -40 degrees C to +120 (-40 degrees F to +250 degrees F) average, 135 degrees C (250 degrees F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.

Power Steering Pressure Hose - High Volumetric Expansion Type (Stabilized Type)

SAE J30-2012 燃料软管和油软管

This SAE standard covers fuel, oil, or emission hose for use in coupled and uncoupled applications, for use with gasoline, oil, diesel fuel, lubrication oil, or the vapors present in either the fuel system or in the crankcase of internal combustion engines in mobile or stationary applications. This standard covers the hose portion only. If assembly / coupling is required, that is to be agreed to between the customer and assembler, along with the specific requirements.

Fuel and Oil Hoses