43.040.99 其他道路车辆装置 标准查询与下载

NF R19-501-8:2011 道路车辆.液压管路部件清洁度.第8部分:显微分析法测定颗粒性质.

Road vehicles - Cleanliness of components of fluid circuits - Part 8 : particle nature determination by microscopic analysis.

NF R19-501-5:2011 道路车辆.液压管路部件清洁度.第5部分:在功能试验台上萃取污染物的方法.

Road vehicles - Cleanliness of components of fluid circuits - Part 5 : method of extraction of contaminants on functional test bench.

NF R19-501-6:2011 道路车辆.液压管路部件清洁度.第6部分:重量分析法测定颗粒质量.

Road vehicles - Cleanliness of components of fluid circuits - Part 6 : particle mass determination by gravimetric analysis.

NF R19-501-4:2011 道路车辆.液压管路部件清洁度.第4部分:超声技术萃取污染物的方法.

Road vehicles - Cleanliness of components of fluid circuits - Part 4 : method of extraction of contaminants by ultrasonic techniques.

NF R19-501-3:2011 道路车辆.流体电路元件的清洁.第3部分:压力冲洗污染物的提取方法.

Road vehicles - Cleanliness of components of fluid circuits - Part 3 : method of extraction of contaminants by pressure rinsing.

NF R19-501-7:2011 道路车辆.液压管路部件清洁度.第7部分:显微分析测量粒径和计数.

Road vehicles - Cleanliness of components of fluid circuits - Part 7 : particle sizing and counting by microscopic analysis.

NF R19-501-9:2011 道路车辆.液压管路部件清洁度.第9部分:自动消光颗粒计数器测量粒径和计数.

Road vehicles - Cleanliness of components of fluid circuits - Part 9 : particle sizing and counting by automatic light extinction particle counter.

SAE J2884-2009 热固弹性体的规格体系

This document provides a method/ procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use; recycled; or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum % must be specified using a "Z" suffix. This classification system covers thermoset High Consistency Elastomers (HCE's) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F 2468.

Thermoset Elastomer Specification System

SAE J1508-2009 软管夹具规范

This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. This document is compiled for the specific purpose of describing the basic characteristics and minimum performance requirements recommended by the manufacturers. No application recommendations are intended or implied. For the benefit of the user in selecting appropriate products for their application, the committee has published ancillary documents that may assist you in this selection. The documents are SAE J1610, SAE J1697, and TMC RP 332.

Hose Clamp Specifications

JIS K 2397 AMD 1:2009 汽车用除冰液和除霜液(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14 Consequently, JIS K 2397:1991 is partially replaced with this Amend- ment.

Deicing and defrosting fluids for automobiles (Amendment 1)

SNI 7520-2009 M型、N型与O型机动车辆玻璃雨刮器(汽车雨刮器)

M-type, N-type and O-type motor vehicle glass wipers (car wipers)

SNI 2770.2-2009 L类机动车辆的后视镜

Rear view mirrors for Class L motor vehicles

SAE J30-2008 燃料软管和油软管

This SAE standard covers fuel, oil, or emission hose for use in coupled and uncoupled applications, for use with gasoline,oil, diesel fuel, lubrication oil, or the vapors present in either the fuel system or in the crankcase of internal combustionengines in mobile or stationary applications. This standard covers the hose portion only. If assembly / coupling isrequired, that is to be agreed to between the customer and assembler, along with the specific requirements.

Fuel and Oil Hoses

TIS 1467-2007 汽车安全带安装固定点,ISOFIX固定点及上固定点系统

Safety.belt anchorages, isofix anchorages systems and isofix top tether anchorages

KS R ISO 16844-5:2007 道路车辆.速度记录器系统.第5部分:安全的CAN接口

이 규격은 도로차량의 운행 기록 장치와 차량 장치 간에 이루어지는 디지털 정보의 안전한 교

Road vehicles－Tachograph systems－Part 5：Secured CAN interface

KS R ISO 16844-5-2007(2017) 道路车辆行车记录仪系统第5部分:安全CAN接口

Road vehicles－Tachograph systems－Part 5：Secured CAN interface

BS ISO 16232-8:2007 道路车辆.液压管路部件清洁度.显微分析测定颗粒性质

This part of ISO 16232 describes a method for determining the nature of contaminant particles by identifying their elemental chemical composition using energy dispersive X-ray spectroscopy (EDX) in combination with a scanning electron microscope (SEM). The contaminant particles are extracted from automotive parts or components and deposited on the surface of a membrane filter. In addition to the number and size of particles as described in ISO 16232-7, this measurement gives the elemental composition of the particles analysed. This information can be used to classify the particles into likely material groups 1). This method cannot determine the nature of organic material 2). The analyses can either be carried out manually or fully automatically, provided the appropriate equipment is available.

Road vehicles - Cleanliness of components of fluid circuits - Particle nature determination by microscopic analysis

BS ISO 16232-4:2007 道路车辆.液压管路部件清洁度.超声波技术萃取污染物的方法

This part of ISO 16232 describes the principles of extraction of contaminants from a component either by immersion in an ultrasonic bath or by applying ultrasonic vibrations directly via sonotrodes. It is preferably applied to small and medium sized components of various geometry of which both internal and/or external surfaces have to be examined (e.g. joint seals, gears, etc). It is also applicable to small parts to be analysed in batches. This method can be used on its own or in association with other methods of extraction described in the ISO 16232 series. Unless otherwise specified, this part of ISO 16232 deals with particulate contamination only. It does not, therefore, cover appearance defects or contamination by liquid or gaseous materials. It covers the amount and the nature of residual particles resulting from manufacturing processes and from the environment.

Road vehicles - Cleanliness of components of fluid circuits - Method of extraction of contaminants by ultrasonic techniques

BS ISO 16232-3:2007 道路车辆.液压管路部件清洁度.压力漂洗萃取污染物的方法

This part of ISO 16232 describes the principles of extraction of contaminants from a component by pressure rinsing. It is preferably applied to components of which the surface to be examined is accessible by a jet of test liquid. This method can be employed on its own or in association with other methods of extraction described in the ISO 16232 series. Unless otherwise specified, this part of ISO 16232 deals with particulate contamination only. It does not, therefore, cover appearance defects or contamination by liquid or gaseous materials. It covers the amount and the nature of residual particles resulting from manufacturing processes and from the environment.

Road vehicles - Cleanliness of components of fluid circuits - Method of extraction of contaminants by pressure rinsing

BS ISO 16232-6:2007 道路车辆.液压管路部件清洁度.重量分析法测定颗粒质量

The purpose of this part of ISO 16232 is to determine the mass of particulate contamination by gravimetric analysis. Contaminants are separated from the extraction liquid by filtration. It applies to automotive components in contact with a fluid. Unless otherwise specified, this part of ISO 16232 deals with particulate cleanliness only. It does not, therefore, cover appearance defects or contamination by liquid or gaseous materials. It covers the amount of residual particulate contaminants resulting from manufacturing processes and from the environment.

Road vehicles - Cleanliness of components of fluid circuits - Particle mass determination by gravimetric analysis