43.040.99 其他道路车辆装置 标准查询与下载

BS ISO 16232-9:2007 道路车辆.液压管路部件清洁度.自动消光颗粒计数器测量粒径和计数

This part of ISO 16232 defines methods for determining the size distribution of particulate contaminants extracted from automotive components using techniques described in ISO 16232-3, ISO 16232-4 and ISO 16232-5, using automatic light extinction particle counter instruments (APC). It only applies to the analysis of the whole volume of extraction liquid. The size range of particles that can be measured by this technique is limited to

Road vehicles - Cleanliness of components of fluid circuits - Particle sizing and counting by automatic light extinction particle counter

BS ISO 16232-7:2007 道路车辆.液压管路部件清洁度.显微分析测量粒径和计数

This part of ISO 16232 defines methods for determining the size and number of contaminant particles, which have been extracted from components and deposited on the surface of a membrane filter, as determined by using either a light optical microscope (LM) or a scanning electron microscope (SEM). The result of this measurement is the particle size distribution on the membrane filter. As the function of parts and components can be impaired by the presence of a single or a few critical particles, a complete analysis of the total membrane filter surface is essential. These analyses can be performed either manually or automatically using Image Analysis (IA) techniques if the appropriate equipment is available.

Road vehicles - Cleanliness of components of fluid circuits - Particle sizing and counting by microscopic analysis

BS ISO 16232-5:2007 道路车辆.液压管路部件清洁度.在功能试验台上萃取污染物的方法

This part of ISO 16232 describes the principles of extraction of contaminants by test on a laboratory functional test bench with the test liquid flowing under pressure or under vacuum. It is applicable to both active and passive components through which the fluid can easily flow. Unless otherwise specified, this part of ISO 16232 deals with particulate contamination only. It does not, therefore, cover appearance defects or contamination by liquid or gaseous materials. It covers the amount and the nature of residual particles resulting from manufacturing processes and from the environment.

Road vehicles - Cleanliness of components of fluid circuits - Method of extraction of contaminants on functional test bench

BS ISO 16232-10:2007 道路车辆.液压管路部件清洁度.结果表达

Road vehicles - Cleanliness of components of fluid circuits - Expression of results

SAE J189-2003 动力转向回流软管 - 低压

This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 degrees C to +120 degrees C (-40 degrees F to +250 degrees F) average, 135 degrees C (275 degrees F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.

Power Steering Return Hose - Low Pressure

SAE J188-2003 高容积膨胀型动力转向压力软管

This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of -40 degrees C to +120 (-40 degrees F to +250 degrees F) average, 135 degrees C (250 degrees F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.

Power Steering Pressure Hose - High Volumetric Expansion Type

SAE J191-2003 低容积膨胀型动力转向压力软管

This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications at pressures as indicated in Table 1, as flexible connections within the temperature range of -40 degrees C (-40 degrees F) to 121 degrees C (250 degrees F) average, 135 degrees C (275 degrees F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is not required.

Power Steering Pressure Hose - Low Volumetric Expansion Type

KS R 4083-1-2001 道路车辆.旅居车和轻型挂车.牵引杆的机械强度计算.第1部分:钢牵引杆

이 규격은 한국산업규격(이하 규격이라 한다.)으로서 캐러밴 또는 트레일러에 용접된 혹은 다

Road vehicles ? Caravans and light trailers ? Calculationof the mechanical strength of the drawbar ? Part 1 : Steel drawbars

KS R 4083-1-2001(2011) 公路车辆 大篷车和轻型拖车 牵引杆机械强度的计算 第1部分:钢牵引杆

Road vehicles?Caravans and light trailers?Calculationof the mechanical strength of the drawbar?Part 1 : Steel drawbars

TIS 1666-1998 声学.用于测量道路车辆发射噪声的试验车道规范

Acoustics.specification of test tracks for the purpose of measuring noise emitted by road vehicles

SAE J942-1999 客车挡风玻璃清洗系统

This SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or less: a. Minimum performance standards for the windshield washer system. b. Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c. Uniform terminology of windshield washer system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d. Guides for the design and location of components of the systems for function, servicing of the system, etc. The minimum performance requirements and test procedures, outlined in this document, are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised as additional data on windshield washer system performance are developed.

Passenger Car Windshield Washer Systems

SAE J903-1999 客车雨刷系统

The scope of this SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GBW or 4500 kg (10 000 lb) or less: a. Minimum performance standards for windshield wiper systems. b. Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c. Uniform terminology of windshield wiper system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d. Guides for the design and location of components of the systems for function, servicing of the system, etc. The test procedures and minimum performance standards, outlined in this document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed.

Passenger Car Windshield Wiper Systems

SAE J2287-1999 带有完整搭接和肩带约束的汽车座椅推荐设计和性能标准

This SAE Recommended Practice defines minimum performance standards, qualification requirements, and minimum documentation requirements for Integrated Lap and Shoulder Restraint (to) equipped Seats (IL&SRTS). The goal is to achieve comfort, durability, and occupant protection under expected and foreseeable normal operation loads. The document attempts to define test and evaluation criteria to demonstrated performance at peak operational loads, while attempting to maintain the seats ability to meet loads set forth in FMVSS 207, 210, and ECE 14, 16, and 17. This document also provides guidance for design by enumerating certain design goals to enhance comfort, serviceability, and safety. Guidance for test procedures, measurements, equipment, and interpretation of results may be presented to promote uniform techniques and to achieve acceptable data. While this document addresses system performance, responsibility for the seating systems is divided between the seat supplier and the vehicle OEM. The seat suppliers responsibility consists of meeting all the established system performance requirements and obtaining and supplying to the vehicle OEM all the data prescribed by this document. The vehicle OEM has the ultimate system responsibility in assuring that all requirements for safe seat applications have been met. This document addresses the static performance criteria for IL&SRTS systems applied to licensed motor vehicles for purposes of transportation.

Recommended Design and Performance Standard for Seats with Integrated Lap and Shoulder Restraints

SAE J30-1998 燃油和机油软管 FSC 4720

This SAE Standard covers fuel and oil hose, coupled and uncoupled, for use with gasoline, oil, diesel fuel, lubrication oil, or the vapor present in either the fuel system or in the crankcase of internal combustion engines in mobile, stationary, and marine applications. Section 7 covers hose primarily intended to meet the demands of fuel injection systems. Sections 10 and 11 cover hose intended to meet low fuel permeation requirements.

Fuel and Oil Hoses FSC 4720

SAE J190-1998 金属丝编织的动力转向压力软管

This specification covers hose fabricated from wire braid and synthetic rubber, assembled with end fittings for use in automotive applications up to 10.3 MPa (1500 psi) maximum pressure, as flexible connections within the temperature range of -40 ?C to 121 ?C (-40 ?F to +250 ?F) average, 13.5 ?C (275 ?F) maximum peaks. The specification in this SAE Standard originated in the SAE-ASTM Technical Committee on Automotive Rubber (other than tires). They represent the correlation of the best information available from research investigation and production experience on the minimum constructional and performance characteristics essential for new power steering assemblies used as original or replacement equipment. This standard applies to passenger cars. It may prove useful to truck manufacturers, but it is not to be presented as present practices. They also represent the minimum quality recognized by original equipment manufacturers and hose suppliers as essential for satisfactory and safe operation by the hose itself and other coacting parts of the power steering system. The original equipment manufacturer may, at his option, add or alter tests through OEM specifications.

Power Steering Pressure Hose Wire Braid

SAE J1508-1997 软管夹规格

This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. This document is compiled for the specific purpose of describing the basic characteristics and minimum performance requirements recommended by the manufacturers. No application recommendations are intended or implied. For the benefit of the user in selecting appropriate products for their application, the committee has published ancillary documents that may assist you in this selection. The documents are SAE J1610, SAE J1697, and TMC RP 332.

Hose Clamp Specifications

VDA 231-106-1997 机动车辆结构中材料分类.结构与命名

Material classification in motor vehicle construction - Structure and nomenclature

SAE J169-1996 越野操作员外壳空调系统设计指南

Design Guidelines for A/C Systems for Off-Road Operator Enclosures

CNS 8388-1993 汽车轮胎气门嘴伸长杆

本标准适用于汽车复轮内侧轮胎用之气门嘴伸长杆（以下简称伸长杆）。备考：本标准中｛ ｝ 内之单位及数值，系习用单位制。参考：工业用车辆之轮胎气门嘴所用之伸长杆，亦可适用本标准。

Tyre Valve Extensions for Automobiles

CNS 7676-1992 大客车用车门抵门橡胶条

本标准适用于大客车用车门之抵门橡胶条（以下简称抵门橡胶条）。备考：本标准中｛ ｝ 内之单位及数值系习用单位制，兹并记供参考。

Rubber Bumpers of Entrance Doors for Buses