43.060.20 标准查询与下载

ISO 16247:2004 道路车辆.排气系统泄漏的检测.氦试验方法和探测装置规范

This International Standard specifies a helium test method for detecting and localizing gas leaks in the exhaust systems of road vehicles equipped with an internal combustion engine, in order to improve the quality of exhaust gas measurements. In doing so, it completes the requirements of ISO 3929, applicable regulations and, depending on the leak rate to be detected, ISO 13556. The method is particularly applicable for use in automotive workshops, by end-of-line of automotive and exhaust parts manufacturers, in laboratories prior to exhaust emission tests, and in testing and diagnosis stations.

Road vehicles - Detection of exhaust system leaks - Helium test method and detection device specification

KS R 0100-2004 道路车辆 - 喷油泵试验第2部分:静态条件

Road vehicles－Fuel injection pump testing－Part 2：Static conditions

KS R 1125-2004(2009) 组性能测试方法为汽车蒸发排放罐散热保护

Test method of canisters for automobile evaporative emission control systems

KS R 4037-2004(2009) 消声器和排气管的汽车

Muffler and exhaust pipe for automobiles

KS R ISO 7750-1-2003(2013) 商用车辆空气滤清器滤芯尺寸第1部分:A型和B型

Commercial vehicles－Dimensions of air filter elements－Part 1：Types A and B

KS R ISO 7312-2003 道路车辆空气滤清器连接类型A和B

Road vehicles－Air filter connections－Types A and B

KS R ISO 7312:2003 道路车辆空气滤清器连接类型A和B

Road vehicles－Air filter connections－Types A and B

KS R ISO 7750-1:2003 商业车辆.空气过滤器部件尺寸.第1部分:A型和B型

이 규격은 일반적으로 상용차에 사용되는 공기 필터에 대한 필터 엘리먼트의 교환 가능성에 필

Commercial vehicles－Dimensions of air filter elements－Part 1：Types A and B

KS R ISO 7750-2-2003(2013) 道路车辆商用车空气滤清器滤芯尺寸第2部分:C型和D型

Road vehicles－Air filter elements for commercial vehicles－Dimensions－Part 2：Types C and D

KS R ISO 7750-2:2003 商业车辆.空气过滤器部件尺寸.第2部分:C型和D型

이 규격은 일반적으로 상용차용 공기 필터에 대한 필터 엘리먼트의 교환 가능성에 필요한 기본

Road vehicles－Air filter elements for commercial vehicles－Dimensions－Part 2：Types C and D

KS R 0099-2003 汽车燃油喷射泵的试验第1部分:动态条件

ROAD VEHICLES - FUEL INJECTION PUMP TESTING - PART 1;DYNAMIC CONDITIONS

SANS 1501:2002 L类车辆用备用消声系统

This specification covers replacement silencing systems (or their components) that are intended to be fitted to motor vehicles of category L only, designed to operate on public roads and first registered after 1 January 1980. NOTE a) The standards referred to in the specification are listed in appendix A. b) Guidance on the verification of the quality of replacement silencing systems is given in appendix B. c) Except under the standardization mark scheme, assessment of compliance with 3.2(c)(2) and 3.2(c)(3) may require special agreement between the supplier and the purchaser (see 5.2).

Replacement silencing systems for vehicles of category L only

SAE J/ISO 5011-2002 内燃机和压缩机的进气净化设备 性能测试 另见 ISO 5011

This International Standard establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection efficiency, dust capacity, and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This International Standard is applicable to air cleaners used on internal combustion engines and compressors generally used in automotive and industrial applications.

Inlet air cleaning equipment for internal combustion engines and compressors Performance testing See also ISO 5011

KS R 2057-2002(2012) 载重汽车空气弹簧

Air spring for trucks and buses

KS R 2057-2002 货车、客车用空气弹簧

이 규격은 트럭ㆍ버스의 차체 현가에 사용하는 공기 스프링 몸체에 대하여 규정한다.

Air spring for trucks and buses

TIS 1793-1999 道路车辆.压缩点火(柴油机)发动机废气阻光度的测量.发动机加载减速试验

Road vehicles.measurement of opacity of exhaust gas from compression.ignition (diesel) engines.lug.down test

BS ISO 5011:2001 内燃机和压缩机的进气口净化装置.性能测试

This International Standard establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection effciency, dust capacity, and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This International Standard is applicable to air cleaners used on internal combustion engines and compressors generally used in automotive and industrial applications.

Inlet air cleaning equipment for internal combustion engines and compressors. Performance testing

GOST R 41.59-2001 关于审核消音系统更换的统一规定

Настоящие Правила содержат положения об официальном утверждении систем глушителей или их элементов, устанавливаемых в качестве сменных

Uniform provisions concerning the approval of remplacement silencing systems

ISO 5011:2000 内燃机和压缩机的空气进气清洁装置 性能测试

This International Standard establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection effciency, dust capacity, and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This International Standard is applicable to air cleaners used on internal combustion engines and compressors generally used in automotive and industrial applications.

Inlet air cleaning equipment for internal combustion engines and compressors - Performance testing

SAE J2515-1999 制作排气导管的高温材料

A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.

High Temperature Materials for Exhaust Manifolds