43.060.20 标准查询与下载

BS ISO 13556:1999 道路车辆.排气系统泄漏位置的确定和设备规范

This International Standard specifies a method to verify the gas tightness of the exhaust system of road vehicles equipped with an international combustion engine. It is primarily intended to establish a method to detect and localize exhaust system leaks in order to improve the quality of exhaust gas measurements. It is also intended to complete the requirements of ISO 3929 and applicable regulations. The users of this International Standard are warned that: a) certain engines with high valve overlaps camshaft events, especially engines with eight or more cylinders, may not have all exhaust valves closed when the engine is stopped. This issue may cause the leak test to fail. This situation could be corrected by the disassembly of the exhaust valve actuation mechanism using the vehicle or engine manufacturer's recommended procedure; b) national regulations on the subject of pressurizing should be checked before testing; c) detected leakage can be quantified under certain test conditions. This International Standard also specifies the measurement apparatus and necessary devices. This method is particularly recommended for: a) automotive workshops, b) laboratories before any emission tests, c) testing and diagnostic stations. The measurement apparatus can be used at the end of line of automotive and exhaust parts manufacturers. note:1) ISO 3929:1995, Road vehicles— Measurement methods for exhaust gas emissions produced during inspection or maintenance.

Road vehicles - Localization of exhaust system leaks and equipment specifications

SAE J2437-1998 空气启动电机试验程序

This SAE Recommended Practice provides a standard procedure for testing the output performance and plotting the performance curve of air starting motors.

Air Starter Motor Test Procedures

ISO 13556:1998 道路车辆 排气系统泄漏位置的确定和装置的技术规范

This International Standard specifies a method to verify the gas tightness of the exhaust system of road vehicles equipped with an international combustion engine. It is primarily intended to establish a method to detect and localize exhaust system leaks in order to improve the quality of exhaust gas measurements. It is also intended to complete the requirements of ISO 3929 and applicable regulations. The users of this International Standard are warned that: a) certain engines with high valve overlaps camshaft events, especially engines with eight or more cylinders, may not have all exhaust valves closed when the engine is stopped. This issue may cause the leak test to fail. This situation could be corrected by the disassembly of the exhaust valve actuation mechanism using the vehicle or engine manufacturer's recommended procedure; b) national regulations on the subject of pressurizing should be checked before testing; c) detected leakage can be quantified under certain test conditions. This International Standard also specifies the measurement apparatus and necessary devices. This method is particularly recommended for: a) automotive workshops, b) laboratories before any emission tests, c) testing and diagnostic stations. The measurement apparatus can be used at the end of line of automotive and exhaust parts manufacturers. note: 1) ISO 3929:1995, Road vehicles — Measurement methods for exhaust gas emissions produced during inspection or maintenance.

Road vehicles - Localization of exhaust system leaks and equipment specifications

HCRJ 006-1996 汽车磁化节油净化器

Automotive magnetized fuel-saving purifier

HCRJ 007-1996 汽车尾气催化净化器

Automotive Exhaust Catalytic Converter

SAE J1667-1996 重型柴油车突然加速发烟测试规程的推荐实施规程.1996年2月

This SAE Recommended Practice applies to vehicle exhaust smoke measurements made using the Snap-Acceleration test procedure. Because this is a non-moving vehicle test, this test can be conducted along the road side, in a truck depot, a vehicle repair facility, or other test facilities. The test is intended to be used on heavy-duty trucks and buses powered by diesel engines. It is designed to be used in conjunction with smokemeters using the light extinction principle of smoke measurement. This procedure describes how the snap-acceleration test is to be performed. It also gives specifications for the smokemeter and other test instrumentation and describes the algorithm for the measurement and quantification of the exhaust smoke produced during the test. Included are discussions of factors which influence snap-acceleration test results and methods to correct for these conditions. Unless otherwise noted, these correction methodologies are to be considered an integral part of the snap- acceleration test procedure.

Snap-Acceleration Smoke Test Procedure for Heavy-Duty Diesel Powered Vehicles, Recommended Practice February 1996

JIS D 1613:1996 汽车发动机.化油器.试验方法

この規格は，ガソリンを燃料とする一般の自動車用エンジンに用いる気化器(以下，気化器という。)の性能試験方法について規定する。

Automotive engines -- Carburetors -- Test methods

SAE J1723-1995 增压器的测试标准.1995年8月

This test document is applicable to all superchargers not requiring fuel to be added to the inlet air prior to the supercharger. This SAE Standard only applies to bench testing. Any maximum speed, temperature, and pressure ratios supplied by the manufacturer should be for this use only and may not apply to applications of firing engines. This document has been adopted by SAE to specify: a. A standard baiss for supercharger efficiency rating; b. reference inlet air supply test conditions; c. a method for correcting observed efficiency to reference conditions; d. a method for presenting these results in an accurate and usable way; and e. a method to compare superchargers without the affects of engine dynamics and intercooling.

Supercharger Testing Standard, Standard August 1995

SAE J228-1995 气流参考标准

The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods.

Airflow Reference Standards

SAE J1826-1995 涡轮增压器气体架测试规范的推荐实施规程

The test procedures outlined in this SAE Recommended Practice are applicable to single rotorturbochargers having either fixed- or variable-geometry with the following caveat:At this stage in the development of variable-geometry (VG) turbochargers, it would be impractical to generatea detailed practice to cover all types of VG turbochargers which may evolve. However, there is a requirementto quote performance data within a stipulated degree of accuracy and to furnish comprehensive performanceinformation. This will form a basis for this document where further refinements may be added as experienceand necessity dictate.1.1 Purpose—The purpose of this document is to provide a recommended laboratory test procedure andpresentation format for establishing the component performance for a turbocharger. It is intended that this testprocedure be used to determine turbocharger compressor and turbine performance characteristics. Theresulting data are intended for use in turbocharger component performance assessment and development andfor engine/turbocharger matching.

Turbocharger Gas Stand Test Code, Recommended Practice;

JIS D 3607:1993 汽车柴油发动机.高压燃料喷射管道用钢管

Automotive diesel engines -- Steel tubes for high-pressure fuel injection pipes

CNS 6162-1993 汽车用冷却水软管

本标准适用于汽车引擎冷却系统及汽车暖气系统用之冷却水软管（以下简称水管）。备考：本标准中｛｝内之单位及数值，系国际单位制（SI）予并记供参考。

Coolant System Hoses for Automobiles

CNS 6160-1993 汽车水箱之压力盖及注入口颈

本标准适用于汽车用水箱之压力盖及注入口颈。备考：1. 使用量较少之中、大型压力盖及注入口颈，于附录 2 中规定之。2. 本标准中｛｝内之单位及数值系习用单位制，予并记供参考。

Pressure Caps and Filler Necks for Automobile Radiators

ANSI/SAE J254-1993 排放废气测量用仪器和技术

Instrumentation and Techniques for Exhaust Gas Emissions Measurement

ANSI/SAE J1088-1993 小型多用途发动机排气污染的测量试验程序

Test Procedure for the Measurement of Exhaust Emissions from Small Utility Engines

DIN 25043-2 Bb.1:1992 客车和轨道车辆.结构测量.测量方法 .数据记录活页表格

Passenger coaches and railcars; constructional measuring; measuring methods; data record-sheet

DIN 25043-1:1992 客车和轨道车辆.结构测量.测量原则

Passenger coaches and railcars; constructional measuring; principles of measuring

DIN 25043-2:1992 客车和轨道车辆.结构测量.测量方法

The document applies to the construction measuring of passenger coaches and railcars. It defines measuring methods and tolerances for underframes.

Passenger coaches and railcars; constructional measuring; measuring methods

ISO 7750-1:1992 商业车辆 空气滤清器滤芯尺寸 第1部分:A型和B型

Specifies the dimensions necessary for interchangeability. Two filter element types, A and B, are specified. Types A and B are not interchangeable. This part of ISO 7750 may be used for other air filter applications where no specific standards exist.

Commercial vehicles; dimensions of air filter elements; part 1: types A and B

JIS D 3105:1992 汽车发动机用气缸盖密封垫

この規格は，自動車用機関に用いるシりンダへッドガスケット(以下，ガスケットという。)について規定する。

Cylinder head gaskets for automobile engines