43.060.30 标准查询与下载

GB/T 34595-2017 汽车零部件再制造产品技术规范 水泵

The technical specifications for remanufacturing of automotive components—Water pump

GB/T 34596-2017 汽车零部件再制造产品技术规范 机油泵

The technical specifications for remanufacturing of automotive components—Oil pump

GB/T 28954-2012 汽车发动机.旋装式机油滤清器.连接尺寸

本标准规定了汽车发动机润滑油过滤用全流旋装式滤清器的基本尺寸、名称和标记″本标准适用于汽车发动机润滑油过滤用全流旋装式滤清器的互换性”

Automotive engines.Spin-on filters for lubricating oil.Connect dimensions

GB/T 6791-2012 道路车辆 火花塞及其气缸盖安装孔 基本特征及尺寸

本标准规定了火花塞的主要特征及尺寸,包括了接线端子和气缸盖安装孔的尺寸。 本标准适用于道路车辆的电火花点火发动机用火花塞。

Road vehicles.Spark-plugs and their cylinder head housing.Basic characteristics and dimensions

GB/T 18948-2003 轿车和轻型商用车辆 冷却系统用纯胶管和橡胶软管

本标准规定了自重为3．5 t以下(含3．5 t)的轿车和轻型商用车辆内燃机使用的含有l．2一乙二醇基的冷却剂(防冻液)的加压和无压冷却系统中用的纯胶管(非增强橡胶软管)和橡胶软管的要求。 本标准适用于预成型或直接挤出的纯胶管和橡胶软管。 本标准不适用于以短纤维增强胶料制成的橡胶软管。

Rubber--Coolant hoses and tubing for use on private cars and light commercial vehieles--Specification

GB/T 6573-1986 拖拉机柴油机散热器型号编制方法

本标准适用于拖拉机和农用固定式、移动式柴油机冷却水用的管片式水散热器型号。

Cooling water radiators for tractor diesel engines--Method of identification symbols

GB/T 6574-1986 拖拉机柴油机散热器型式、参数和连接尺寸

本标准适用于拖拉机和农用固定式、移动式柴油机冷却水用的管片式水散热器。

Types and dimensions and installation parameters of cooling water radiators for tractor diesel engines

T/CASME 950-2023 汽车散热器铝合金压铸件通用技术条件

本文件规定了汽车散热器铝合金压铸件的技术要求、试验方法、检验规则、标志、包装、运输和贮存。

General technical specification for automotive radiator aluminum alloy casting parts

ASTM D5662-23 测定汽车齿轮油与典型油封弹性体相容性的标准试验方法

Standard Test Method for Determining Automotive Gear Oil Compatibility with Typical Oil Seal Elastomers

ASTM D6107-97(2023) 轻型发动机冷却剂用止漏添加剂的标准规范

Standard Specification for Stop-Leak Additive for Engine Coolants Used in Light Duty Service

T/QGCML 1828-2023 新能源电池组散热装置

本文件规定了新能源电池组散热装置的术语和定义、构成及原理、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于新能源电池组散热装置的生产及检验。

New energy battery pack cooling device

T/JSQA 165-2023 电动汽车热管理液

1）外观、气味、颜色 2）密度 3）冰点 4）沸点 5）导热系数 6）运动粘度 7）电导率 8）灰分 9）pH 10）氯含量、硫酸盐含量 11）硅、硼、磷酸盐、亚硝酸盐含量 12）储备碱度 13）对有机涂料的影响 14）泡沫倾向 15）稳定性试验 16）玻璃器皿腐蚀 17）非金属材料的影响 18）模拟腐蚀台架

Electric Vehicle Thermal Management Fluid

T/QGCML 1498-2023 燃料电池系统用空压机性能试验技术规范

本文件规定了燃料电池系统用空压机性能试验技术规范的术语和定义、试验条件、试验设备、性能试验方法。 本文件适用于燃料电池车用或类似用途的空压机的性能试验。

Technical specifications for performance testing of air compressors for fuel cell systems

T/QGCML 1497-2023 燃料电池系统用加湿器性能试验技术规范

本文件规定了燃料电池系统用加湿器性能试验技术规范的术语和定义、试验条件、试验设备、性能试验方法。 本文件适用于燃料电池车用或类似用途的膜加湿器的性能试验。

Technical specifications for performance testing of humidifiers for fuel cell systems

T/QGCML 1496-2023 燃料电池系统用水泵性能试验技术规范

本文件规定了燃料电池系统用水泵性能试验技术规范的术语和定义、试验条件、试验设备、性能试验方法。 本文件适用于燃料电池车用或类似用途的离心水泵的性能试验。

Technical specifications for water pump performance testing of fuel cell systems

ASTM D7583-16(2023) 约翰迪尔冷却剂空化测试的标准测试方法

1.1  This test method is commonly referred to as the John Deere Cavitation Test.2 The test method defines a heavy-duty diesel engine to evaluate coolant protection as related to cylinder liner pitting caused by cavitation. 1.2  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing sizes. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions. 1.4  Table of Contents:  Scope 1 Referenced Documents 2 Terminology 3 Summary of Test Method 4 Significance and Use 5 Apparatus 6 Test Engine Configuration 6.1 Test Engine 6.1.1 Test Stand Configuration 6.2 Engine Mounting 6.2.1 Intake Air System 6.2.2 Aftercooler 6.2.3 Exhaust System 6.2.4 Fuel System 6.2.5 Coolant System 6.2.6 Oil System 6.2.7 Oil Volume 6.2.7.1 Pressurized Oil Fill System 6.2.7.2 External Oil System 6.2.7.3 Oil Sample Valve Location 6.2.7.4 Unacceptable Oil System Materials 6.2.7.5 Crankcase Aspiration 6.3 Blowby Rate 6.4 System Time Responses 6.5 Clearance Measurements 6.6 Engine and Cleaning Fluids 7 Engine Oil 7.1 Test Fuel 7.2 Test Coolant 7.3 Solvent 7.4 Preparation of Apparatus 8 Cleaning of Parts 8.1 General 8.1.1 Engine Block 8.1.2 Cylinder Head 8.1.3 Rocker Cover and Oil Pan 8.1.4 External Oil System 8.1.5 Rod Bearing Cleaning and Measurement 8.1.6 Ring Cleaning and Measurement 8.1.7 Injector Nozzle 8.1.8 Pistons 8.1.9 Engine Assembly 8.2 General 8.2.1 Parts Reuse and Replacement 8.2.2 Build-Up Oil 8.2.3 Coolant Thermostat 8.2.4 Fuel Injectors 8.2.5 New Parts 8.2.6 Operational Measurements 8.3 Units and Formats 8.3.1 Instrumentation Calibration 8.3.2 Fuel Consumption Rate Measurement Calibration 8.3.2.1 Temperature Measurement Calibration 8.3.2.2 Pressure Measurement Calibration 8.3.2.3 Temperatures 8.3.3 Measurement Location 8.3.3.1 Coolant Out Temperature 8.3.3.2 Coolant In Temperature 8.3.3.3 Fuel In Temperature 8.3.3.4 Oil Gallery Temperature 8.3.3.5 Intake Air Temperature 8.3.3.6 Intake Air after Compressor Temperature 8.3.3.7 Intake Manifold Temperature 8.3.3.8 Exhaust Temperature 8.3.3.9 Exhaust after Turbo Temperature 8.3.3.10 Additional Temperatures 8.3.3.11 Pressures 8.3.4 Measurement Location and Equipment 8.3.4.1 Condensation Trap 8.3.4.2 Coolant Pressure 8.3.4.3 Fuel Pressure 8.3.4.4 Oil Gallery Pressure 8.3.4.5 Intake Air Pressure 8.3.4.6 Intake Air after Compressor Pressure 8.3.4.7 Intake Manifold Pressure 8.3.4.8 Exhaust after Turbo Pressure 8.3.4.9 Crankcase Pressure 8.3.4.10 Additional Pressures 8.3.4.11 Flow Rates 8.3.5 Flow Rate Location and Measurement Equipment 8.3.5.1 Blowby 8.3.5.2 Fuel Flow 8.3.5.3 Engine/Stand Calibration and Non-Reference Coolant    Tests 9 General 9.1 New Test Stand 9.2 New Test Stand Calibration 9.2.1 Stand Calibration Period 9.3 Stand Modification and Calibration Status 9.4 Test Numbering System 9.5 General 9.5.1 Reference Coolant Tests 9.5.2 Non-Reference Coolant Tests 9.5.3 Reference Coolant Test Acceptance 9.6 Reference Coolant Accountability 9.7 Last Start Date 9.8 Donated Reference Coolant Test Programs 9.9 Adjustments to Reference Coolant Calibration Periods 9.10 Procedure Development 9.10.1 Parts and Fuel Shortages 9.10.2 Reference Coolant Test Data Flow 9.10.3 Special Use of The Reference Coolant Calibration System 9.10.4 Procedure 10 Engine Installation and Stand Connections 10.1 Break-in 10.2 Coolant System Fill for Break-in 10.2.1 Oil Fill for Break-in 10.2.2 Engine Build Committed 10.2.3 Break-in Conditions 10.2.4 Shutdown during Break-in 10.2.5 250-Hour Test Procedure 10.3 Coolant System Fill for Test 10.3.1 Zero-Hour Coolant Sample 10.3.1.1 Oil Fill for Test 10.3.2 Zero-Hour Oil Sample 10.3.2.1 Warm-Up 10.3.3 Warm-up Conditions 10.3.3.1 Shutdown during Warm-up 10.3.3.2 20-Hour Steady State Extended Break-in 10.3.4 20-Hour Steady State Extended Break-in Conditions 10.3.4.1 Shutdown during 20-Hour Extended Break-in 10.3.4.2 230-Hour Cyclic 10.4 230-Hour Cyclic Conditions 10.4.1 Shutdown during 230-Hour Cyclic 10.4.2 Shutdown and Maintenance 10.5 Normal Shutdown 10.5.1 Emergency Shutdown 10.5.2 Maintenance 10.5.3 Downtime 10.5.4 Operating conditions 10.6 Stage Transition Times 10.6.1 Test Timer 10.6.2 Operational Data Acquisition 10.6.3 Operational Data Reporting 10.6.4 Coolant Sampling 10.6.5 Oil Sampling 10.6.6 End of Test (EOT) 10.7 Shutdown 10.7.1 Oil Drain 10.7.2 Coolant Drain 10.7.3 Engine Disassembly 10.7.4 Calculations, Ratings and Test Validity 11 Liner Pit Count 11.1 Coolant Analysis 11.2 Oil Analyses 11.3 Assessment of Operational Validity 11.4 Report 12 Report Forms 12.1 Reference Coolant Test 12.2 Electronic Transmission of Test Results 12.3 Precision and Bias 13 Precision 13.1 Intermediate Precision Conditions 13.1.1 Intermediate Precision Limit 13.1.2 Reproducibility Conditions 13.2 Reproducibility Limit 13.2.1 Bias 13.3 Keywords 14 Annexes   Safety Precautions Annex A1 Intake Air Aftercooler Annex A2 Engine Build Parts Kit Annex A3 Sensor Locations, Special Hardware, and Engine Block    Modifications Annex A4 Fuel Specifications Annex A5 John Deere Service Publications Annex A6 Specified Units and Formats Annex A7 Report Forms and Data Dictionary Annex A8 Coolant Analysis Annex A9 Oil Analysis Annex A10 Determination of Operational Validity Annex A11 Typical System Configurations Appendix X1 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for John Deere Coolant Cavitation Test

T/QGCML 1259-2023 电子油泵

本文件规定了电子油泵的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于电子油泵的生产和检验。

Electronic oil pump

T/CPCIF 0244-2023 电池用低电导率冷却液

本文件规定了电池用低电导率冷却液的产品分类和标记、技术要求和试验方法、检验规则、标志和包装、贮存、运输和使用。 本文件产品由乙二醇、去离子水组成，并辅以防腐剂、杀菌剂、消泡剂等非离子型助剂组合而成，适用于换热温度不超过110 ℃的氢燃料电池、动力电池、充电桩等需要较低导电介质的热利用循环系统。 本文件适用于系统材质限定于铝合金、铜系金属、不锈钢304、不锈钢316L等金属材料，系统需要加装特定滤除离子设备。

Low conductivity coolant for battery

KS R ISO 6415-2022 内燃机 旋装式润滑油过滤器 尺寸

Internal combustion engines－Spin-on filters for lubricating oil－Dimensions

T/CASMES 113-2022 润滑油站

本文件规定了润滑油站的术语和定义、设计规范、技术要求、试验方法、检验规则、文件资料、标志、包装、运输和贮存。 本文件适用于国内普通润滑油站（以下简称油站）的设计和制造。

Lube oil system