47.020.20 船用发动机和推进系统 标准查询与下载

T/ZHUSA 002-2022 无人水面艇动力系统维护与保养规范

无人船艇动力系统维护保养规范

Specifications for Maintenance and Maintenance of Unmanned Surface Vehicle Power System

T/CANSI 46-2021 船用可调桨齿轮箱

本文件规定了CKV、CKH、CKTS三个系列船用可调桨齿轮箱（以下简称齿轮箱）的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Marine controllable pitch propeller gearbox

OENORM EN 17763-2021 离心机 船用燃料离心机 在规定的测试条件下测定颗粒分离性能和认证流量（CFR）

Centrifuges - Marine fuel centrifuges - Determination of particle separation performance and certified flow rate (CFR) under defined test conditions

prEN 17763-2021 离心机 船用燃料离心机 在规定的测试条件下测定颗粒分离性能和认证流量（CFR）

Centrifuges - Marine fuel centrifuges - Determination of particle separation performance and certified flow rate (CFR) under defined test conditions

KS V 0421-2021 船用发动机控制台外形尺寸

Outline dimensions of marine engine control consoles

KS V 7225-2021 造船 平板玻璃油位计

Shipbuilding－Flat glass oil level gauges

KS V ISO 484-1-2021 造船 船舶螺旋桨 制造公差 第1部分：直径大于2.50 m的螺旋桨

Shipbuilding－Ship screw propellers－Manufacturing tolerances－Part 1：Propellers of diameter greater than 2.50 m

KS V 4211-2021 船用推进用蒸汽轮机车间试验规范

Shop test code for marine steam turbines for propelling use

KS V 0422-2021 船舶轮机部设备报警指示系统

Alarming and Indicating System of Equipment Used For Engine Department in Ships

KS V 0414-2021 主柴油机试航出力计算方法

Calculation methods for main diesel engine output at sea trial

KS V ISO 484-2-2021 船舶螺旋桨 制造公差 第2部分：直径0.80～2.50m（含）的螺旋桨

Ship screw propellers－Manufacturing tolerances－Part 2：Propellers of diameter between 0.80 and 2.50 m inclusive

FprEN 15609-2021 LPG 设备和附件 用于小船、游艇和其他船只的 LPG 推进系统 安装要求

LPG equipment and accessories - LPG propulsion systems for boats, yachts and other watercraft - Installation requirements

KS V 4018-2020 船用离合器总成

Marine clutch assembly

KS V 4024-2020 船用减速机

Reduction gears for marine use

KS V 4019-2020 船用支柱轴承

Strut bearings for marine use

JT/T 423-2020 购置新船及二手船节能技术要求

Energy-saving technical requirements for purchasing new and second-hand ships

ASTM D7845-20 通过多维气相色谱/质谱法测定海洋燃料油中化学物质的标准测试方法

1.1 This test method covers the quantitative determination of a variety of chemical species in marine fuel oil (bunker fuel oil) by gas chromatography/mass spectrometry. By using the same conditions and by selecting required mass spectral selected ions, the test method may be used for the determination of other species than those for which precision statements and limits of detection have been established. 1.2 An example list of chemical species for which a limit of quantification has been determined by means of this test method is given in Table 1. 1.3 Other refinery hydrocarbon fractions and their mixtures may be tested using the same test method conditions. However, the precision of this test method reflects the compounds in Table 1. 1.4 Results are reported to the nearest 1.0 mg ⁄kg. 1.5 The values stated in SI units are to be regarded as standard. 1.5.1 Exception—Non-SI values are given for psig. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Chemical Species in Marine Fuel Oil by Multidimensional Gas Chromatography/Mass Spectrometry

ISO 22098:2020 船舶和航海技术.螺旋桨空化观测和船体压力测量的全尺寸试验方法

This document specifies a full-scale test method for propeller cavitation observation and hull pressure measurement. The objective of the test is to investigate the propeller cavitation behaviour and its effects on the hull vibration problems. The test method comprises the specification of the test instrumentation and implementation, construction requirements to ensure structural safety, test and measurement procedures, and reporting documentation. This document is applicable to ships in the following stages: — before or during sea-trial, prior to delivery stage (vessels under constructions), and — after delivery stage.

Ships and marine technology — Full-scale test method for propeller cavitation observation and hull pressure measurement

CB/T 4505-2020 舷外机通用技术规范

General technical specifications for outboard motors

KS V 0411-2019 船舶推进机械输出的术语和定义

Terminology and definition of output ofpropulsion machinery installed in ships