49.025.10 钢 标准查询与下载
共找到 2315 条与 钢 相关的标准，共 155 页
This specification covers a corrosion resistant steel in the form of wire type identified under the Unified Numbering System as UNS S30500.
Steel, Corrosion Resistant, Safety Wire, 18Cr - 11.5Ni (UNS S30500) Solution Heat Treated, Cold Finished
- ICS
- 49.025.10
- CCS
- 发布
- 2015-03-01
- 实施
Aerospace series - Steel X105CrMo17 (1.4125) - Hardened and tempered - Hand and die forgings - De <= 150 mm; German and English version EN 2226:2014
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2015-02
- 实施
1.1 The reference radiographs provided in the adjunct to this standard illustrate various types and degrees of discontinuities occurring in thin-wall steel investment castings.2 Use of this standard for the specification or grading of castings requires procurement of the adjunct reference radiographs which illustrate the discontinuity types and severity levels. They are intended to provide the following: 1.1.1 A guide enabling recognition of thin-wall steel casting discontinuities and their differentiation both as to type and degree through radiographic examination. 1.1.2 Example radiographic illustrations of discontinuities and a nomenclature for reference in acceptance standards, specifications and drawings. 1.2 Two illustration categories are covered as follows: 1.2.1 Graded—Six common discontinuity types each illustrated in eight degrees of progressively increasing severity. 1.2.2 Ungraded—Twelve single illustrations of additional discontinuity types and of patterns and imperfections not generally regarded as discontinuities. 1.3 The reference radiographs were developed for casting sections up to 1 in. (25.4 mm) in thickness. 1.4 This document may be used where there is no other applicable document existing or for other material thicknesses for which it is found to be applicable and for which agreement has been reached between the purchaser and manufacturer. Note 1: The set of reference radiographs, produced with X-rays in the range from 130 to 250 kVp, consist of 16 plates (81/2 by 11 in. (216 by 279 mm)) in a 93/4 by 111/2-in. (248 by 292-mm) ring binder. 1.5 From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard. 1.6 These film reference radiographs are not intended to illustrate the types and degrees of discontinuities found in aerospace investment castings when performing digital X-ray imaging. When performing digital X-ray imaging of these castings, refer ......
Standard Reference Radiographs of Investment Steel Castings for Aerospace Applications
- ICS
- 49.025.10
- CCS
- 发布
- 2015
- 实施
1.1 This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME specification B16.5. 1.2 Several grades of martensitic, austenitic, age hardening, and austenitic-ferritic stainless steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 The following safety hazards caveat pertains only to test methods portions 8.1, 8.2, 9.5 – 9.7, and Section 10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
- ICS
- 49.025.10
- CCS
- 发布
- 2015
- 实施
1.1 This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME specification B16.5. 1.2 Several grades of martensitic, austenitic, age hardening, and austenitic-ferritic stainless steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 The following safety hazards caveat pertains only to test methods portions 8.1, 8.2, 9.5 – 9.7, and Section 10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
- ICS
- 49.025.10
- CCS
- V11;J16
- 发布
- 2015
- 实施
1.1 This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME Specification B16.5. 1.2 Several grades of alloy steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 The following safety hazards caveat pertains only to test methods portions, 8.1, 8.2, and 9.5 – 9.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
- ICS
- 49.025.10
- CCS
- J16
- 发布
- 2015
- 实施
This British Standard specifies requirements for 2.5% nickel-chromium-molybdenum (high carbon) steel supplied in the following forms,and as parts.
Specification for 2.5% nickel-chromium-molybdenum (high carbon) steel billets, bars, forging and parts (1 160 - 1 310 MPa: limiting ruling section 155 mm)
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-12-31
- 实施
- 2014-12-31
Cette Norme européenne spécifie les exigences relatives à :Acier X105CrMo17 (1.3544)Trempé et revenuBarresDe < ou = à 150 mmpour applications aérospatiales.
Aerospace series - Steel X105CrMo17 (1.3544) - Hardened and tempered - Bars - De < or = 150 mm
- ICS
- 49.025.10
- CCS
- 发布
- 2014-12-26
- 实施
- 2014-12-26
This specification covers a free-machining carbon steel in the form of bars.
Steel Bars Free-Machining Cold Drawn (SAE 1212 or SAE 1215)
- ICS
- 49.025.10
- CCS
- 发布
- 2014-12-01
- 实施
Aerospace series - Steel X12CrNiMoV12-3 (1.4933) - 900 MPa <= Rm <= 1100 MPa, Bars - De <= 150 mm; German and English version EN 2278:2014
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-12
- 实施
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted and electroslag remelted (ESR) - Hardened and tempered - Bar - De <= 200 mm - 900 MPa <= Rm <= 1050 MPa; German and English version EN 4721:2014
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-12
- 实施
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted and electroslag remelted (ESR) - Hardened and tempered - Bar - De <= 200 mm - 1150 MPa <= Rm <= 1300 MPa; German and English version EN 4720:2014
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-12
- 实施
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Forgings - D e <= 200 mm - 900 MPa <= R m <= 1050 MPa; German and English version EN 4630:2014
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-12
- 实施
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Forgings - De ? 200 mm - 900 MPa ? Rm ? 1 050 MPa
- ICS
- 49.025.10
- CCS
- 发布
- 2014-11-28
- 实施
Cette norme européenne spécifie les exigences relatives à :Acier X4CrNiMo16-5-1 (1.4418)Élaboré à l'airAdouciDemi-produits pour forgeageDe < ou = à 300 mmpour les applications aérospatiales.
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Softened - Forging stock - De < or = 300 mm
- ICS
- 49.025.10
- CCS
- 发布
- 2014-11-22
- 实施
- 2014-11-22
Aerospace series. Steel X4CrNiMo16-5-1 (1.4418). Air melted. Hardened and tempered. Forgings. De
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-10-31
- 实施
- 2014-10-31
Aerospace series. Steel X12CrNiMoV12-3 (1.4933). 900 MPa
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-10-31
- 实施
- 2014-10-31
Aerospace series. Steel X4CrNiMo16-5-1 (1.4418). Air melted and electroslag remelted (ESR). Hardened and tempered. Bar. De
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-10-31
- 实施
- 2014-10-31
Aerospace series. Steel X4CrNiMo16-5-1 (1.4418). Air melted and electroslag remelted (ESR). Hardened and tempered. Bar. De
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-10-31
- 实施
- 2014-10-31
This European Standard specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418), air melted and electroslag remelted (ESR), hardened and tempered, bar, De
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted and electroslag remelted (ESR) - Hardened and tempered - Bar - De <= 200 mm - 900 MPa <= Rm<= 1050 MPa
- ICS
- 49.025.10
- CCS
- V11
- 发布
- 2014-10
- 实施
