49.025.20 铝 标准查询与下载

SAE AMS4116H-2009 溶液热处理冷加工1.0Mg-0.60Si-0.30Cu-0.20Cr(6061-T4)铝合金棒材,杆材和线材

This specification covers an aluminum alloy in the form of bars, rods, and wire. These products have been used typically for parts where moderate ductility, formability, and response to precipitation heat treatment, but usage is not limited to such applications.

Aluminum Alloy, Bars, Rods, and Wire 1.0Mg 0.60Si 0.30Cu 0.20Cr (6061-T4) Cold Finished, Solution Heat Treated

SAE AMS4286F-2009 7Si-0.32Mg (356.0-T51)沉淀热处理永久铸模铝合金铸件

This specification covers an aluminum alloy in the form of permanent mold castings. These castings have been used typically for components requiring moderate strength up to 450 °F (230 °C), but usage is not limited to such applications.

Aluminum Alloy Castings, Permanent Mold 7Si 0.32Mg (356.0-T51) Precipitation Heat Treated

SAE AMS4115H-2009 1.0Mg-0.60Si-0.28Cu-0.20Cr淬火轧制或冷加工铝合金条,棒,丝和闪速对焊环(6061-0)

This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, and wire, of flash welded rings, and of stock for flash welded rings. These products have been used typically for parts requiring moderate strength, especially where such parts require brazing or welding during fabrication, but usage is not limited to such applications.

Aluminum Alloy, Rolled or Cold-Finished, Bars, Rods, Wire, and Flash Welded Rings Annealed 1.0Mg 0.60Si 0.28Cu 0.20Cr, (6061-0)

SAE AMS4070M-2009 2.5Mg-0.25Cr(5052-0)淬火拉制圆形无缝铝合金管

This specification covers an aluminum alloy in the form of drawn, round seamless tubing. This tubing has been used typically for parts, such as brackets, conduits, and low-pressure fluid lines, requiring good weldability, moderate strength, and good resistance to corrosion, but usage is not limited to such applications.

Aluminum Alloy, Drawn, Round Seamless Tubing 2.5Mg 0.25Cr (5052-0) Annealed

DIN EN 3115:2009 航空航天系列.铝合金7050-T73.实心铆钉用线材.D≤10 mm.德文版本和英文版本EN 3115-2009

This standard specifies the requirements relating to: Aluminium alloy 7050-T73 Wire for solid rivets D 10 mm for aerospace applications.

Aerospace series - Aluminium alloy 7050-T73 - Wire for solid rivets - D 10 mm; German and English version EN 3115:2009

LST EN 3115-2009 航空航天系列 铝合金 7050-T73 实心铆钉用钢丝 D < 10 毫米

Aerospace series - Aluminium alloy 7050-T73 - Wire for solid rivets - D ? 10 mm

LST EN 2117-2009 航空航天系列 铝合金 AL-P5056A（5056A）-H32 实心铆钉用线材 D 10 毫米

Aerospace series - Aluminium alloy AL-P5056A (5056A)-H32 - Wire for solid rivets - D ? 10 mm

LST EN 2116-2009 航空航天系列 铝合金 2017A-T42 实心铆钉用线材 D 10 毫米

Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets - D ? 10 mm

LST EN 2115-2009 航空航天系列 铝合金 2117-T42 实心铆钉用线材 D 10 毫米

Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets - D ? 10 mm

SAE AMS4133E-2009 4.4Cu 0.85Si 0.80Mn 0.50Mg (2014-T6)溶解和沉淀热处理的铝合金锻件和轧制环材

This specification covers an aluminum alloy in the form of die forgings, hand forgings, rolled rings, and forging stock. These products have been used typically for aircraft structural members requiring moderately high strength. Certain design and processing procedures may cause these forgings and rolled rings to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy Forgings and Rolled Rings 4.4Cu 0.85Si 0.80Mn 0.50Mg (2014-T6)Solution and Precipitation Heat Treated

SAE AMS4118L-2009 4.0Cu 0.70Mn 0.60Mg 0.50Si溶解热处理的铝合金轧制或冷精整棒材、杆材和线材

This specification covers an aluminum alloy in the form of bars, rods, and wire. These products have been used typically for parts requiring good strength and whose fabrication does not involve welding, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire, 4.0Cu 0.70Mn 0.60Mg 0.50Si, Solution Heat Treated

SAE AMS4011D-2009 99.45Al(1145-0)型退火的铝箔和小型量规薄板材

This specification covers aluminum in the form of foil and light gage sheet. These products have been used typically for capacitors, electronic components, and sound/vibration damping tape, but usage is not limited to such applications.

Aluminum, Foil and Light Gage Sheet 99.45Al (1145-0) Annealed

DS/EN 2117:2009 航空航天系列 铝合金 AL-P5056A（5056A）-H32 实心铆钉用线材 D <= 10 mm

This standard specifies the requirements relating to:Aluminium alloy AL-P5056A (5056A)-H32Wire for solid rivetsD < or = 10 mmfor aerospace applications.

Aerospace series - Aluminium alloy AL-P5056A (5056A)-H32 - Wire for solid rivets - D <= 10 mm

DS/EN 3115:2009 航空航天系列 铝合金 7050-T73 实心铆钉用线材 D <= 10 mm

This standard specifies the requirements relating to:Aluminium alloy 7050-T73 Wire for solid rivets D < or = 10 mm for aerospace applications.

Aerospace series - Aluminium alloy 7050-T73 - Wire for solid rivets - D <= 10 mm

DS/EN 2115:2009 航空航天系列 铝合金 2117-T42 实心铆钉用线材 D <= 10 mm

This standard specifies the requirements relating to:Aluminium alloy 2117-T42Wire for solid rivetsD < or = 10 mmfor aerospace applications.

Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets - D <= 10 mm

DS/EN 2116:2009 航空航天系列 铝合金 2017A-T42 实心铆钉用线材 D <= 10 mm

This standard specifies the requirements relating to:Aluminium alloy 2017A-T42Wire for solid rivetsD < or = 10 mmfor aerospace applications.

Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets - D <= 10 mm

EN 2116:2009 航空航天系列 - 铝合金 2017A-T42 - 实心铆钉用线材 - D ≤ 10 mm

This standard specifies the requirements relating to: Aluminium alloy 2017A-T42 Wire for solid rivets D < or = 10 mm for aerospace applications.

Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets - D ≤ 10 mm

EN 2115:2009 航空航天系列.铝合金2117-T42.实心铆钉用线材.D≤10 mm

This standard specifies the requirements relating to: Aluminium alloy 2117-T42 Wire for solid rivets D

Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets - D less than or equal to 10 mm

EN 2117:2009 航空航天系列.铝合金AL-P5056A(5056A)-H32.实心铆钉用线材.D 10 mm

This standard specifies the requirements relating to: Aluminium alloy AL-P5056A (5056A)-H32 Wire for solid rivets D

Aerospace series - Aluminium alloy AL-P5056A (5056A)-H32 - Wire for solid rivets - D less than or equal to 10 mm

SAE AMS4132F-2008 2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti(2618-T61)溶解和沉淀热处理的铝合金、锻模和手制锻件、轧制环材和锻造原料

This specification covers an aluminum alloy in the form of die forgings, hand forgings, rolled rings, and forging stock. These products have been used typically for rotating parts operating in service up to 450 °F (232 °C) and other parts operating up to 600 °F (316 °C) at low stresses, but usage is not limited to such applications.

Aluminum Alloy, Die and Hand Forgings, Rolled Rings, and Forging Stock 2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti (2618-T61) Solution and Precipitation Heat Treated