49.025.40 橡胶和塑料 标准查询与下载

BS EN 3825:2014 航空航天系列. 硅氟橡胶 (FVMQ). 硬度60 IRHD

Aerospace series. Fluorosilicone rubber (FVMQ). Hardness 60 IRHD

EN 3825:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.60 IRHD硬度

This European Standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 60 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 60 IRHD

EN 3827:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.80 IRHD硬度

This standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 80 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 80 IRHD

EN 3826:2014 航空航天系列.氟硅橡胶（氟硅橡胶）.70 IRHD硬度

This European Standard specifies the properties of fluorosilicone rubber (FVMQ)1), hardness 70 IRHD, for aerospace applications.

Aerospace series - Fluorosilicone rubber (FVMQ) - Hardness 70 IRHD

SAE AMS3305J-2014 通用硅酮橡胶,80硬度计

This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for parts required to operate or seal from -65 to +205 degrees C (-85 to +401 degrees F). Silicone elastomer is resistant to deterioration by weathering and petroleum-base lubricating oil and remains flexible over the temperature range noted. These products are not normally suitable for use in contact with gasoline or aromtic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer.

Silicone@ Rubber General Purpose 80 Durometer

SAE ARP5316D-2014 在硬件组装之前存储弹性体密封件和包括弹性体元件的密封组件

This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life.

Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly

SAE AMS3217/7A-2014 55-65 氟硅氧烷 (FVMQ) 高强度试验板

This specification covers a high strength fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.

Test Slabs, High Strength, Fluorosilicone (FVMQ) 55 - 65

SAE AMS7257E-2014 耐70至80的高温流体的全氟化碳 (Ffkm) 橡胶密封环

Rings, Sealing, Perfluorocarbon (Ffkm) Rubber High Temperature Fluid Resistant 70-80

SAE AS27197B-2014 AMS7268硅橡胶槽模制AMS5516的302耐腐蚀钢粘结密封

Scope is unavailable.

SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, SILICONE RUBBER, AMS7268

SAE AS27198B-2014 MIL-DTL-25988氟硅橡胶槽模制AMS5516的302耐腐蚀钢粘结密封

Scope is unavailable.

SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROSILICONE RUBBER, MIL-DTL-25988

SAE AMS3194E-2014 坚定的极端低温闭孔硅橡胶海绵

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Firm, Extreme Low Temperature

SAE AMS3325F-2014 耐燃料及耐油氟硅(FVMQ)橡胶,55-65

This specification covers a fluorosilicone (FVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts requiring resistance to jet fuel and lubricating oils, but usage is not limited to such applications. Generally, products are usable over a temperature range of -76 to +302 degrees F (-60 to +150 degrees C); each application, however, has to be considered individually.

Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 55 - 65

SAE AMS-R-83485A-2014 在低温条件下具备改良性能的氟烃弹性体橡胶

This specification covers high temperature, compression set, and fluid resistant fluorocarbon elastomer sheets, strips, molded parts, and extruded shapes for aeronautical and aerospace applications. This material differs from other fluorocarbon elastomers because of its improved low temperature performance of approximately 25 °F.

Rubber, Fluorocarbon Elastomer, Improved Perfrormance At Low Temperatures

SAE AMS3193E-2014 中等温度和极低温度的闭孔硅橡胶海绵

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Medium, Extreme Low Temperature

SAE AMS3195G-2014 中等硅泡沫橡胶闭孔泡沫

This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Silicone Rubber Sponge Closed Cell, Medium

SAE AMS3356F-2014 电气级耐润滑油和耐压缩永久变形的硅酮橡胶.55-65

This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, extrusions and molded shapes. Primarily for parts required to operate or seal from -55 to +230 degrees C (-67 to +446 degrees F), compounded especially for aircraft piston engine oil resistance, low compression set, and controlled dielectric strength. Silicone elastomer is resistant to deterioration by weathering and by high-aniline-point petroleum-base oils and remains flexible over the temperature range noted. The elastomer is not normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of

Silicone (VMQ) Rubber, Lubricating Oil and Compression Set Resistant, Electrical Grade, 55-65

SAE AMS3306C-2014 硅树脂橡胶,1200 psi(8.27 MPa),高模55-65

This specification covers a silicone elastomer in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically as seals from -65 degrees to +225 degrees C (-85 degrees to +437 degrees F), compounded especially for high strength. Silicone rubber is resistant to deterioration by weathering and by high-aniline-point petroleum-base lubricating oil and phosphate ester hydraulic fluid, and remains flexible over the temperature range noted. This material is not normally suitable for use in contact with hydrocarbon-based fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer, but usag

Rubber, Silicone 1200 psi (8.27 MPa), High Modulus 55 - 65

SAE AMS3349D-2014 1100psi(7.58MPa)抗拉强度的高弹性硅酮橡胶.65-75

This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, molded shapes and extrusions. These products have been used typically for parts required to operate or seal from -65 to +205 degrees C (-85 to +401 degrees F), compounded especially for high strength and resiliency, but usage is not limited to such applications. Silicone elastomer is resistant to deterioration by weathering and aircraft piston engine oil and remains flexible over the temperature range noted. This material is not normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the

Silicone (VMQ) Rubber, 1100 psi (7.58 MPa) Tensile Strength, High Resiliency, 65 - 75

SAE AMS3348D-2014 1150psi(7.93MPa)抗拉强度的高弹性硅酮橡胶.25-35

This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, molded shapes, and extrusions.

Silicone (VMQ) Rubber 1150 Psi (7.93 MPa) Tensile Strength, High Resiliency 25-35

SAE AMS3338G-2014 耐超低温的硅酮橡胶.75-85

This specification covers a silicone (PVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for parts required to operate or seal from -85 to +230 degrees C (-121 to +446 degrees F), compounded especially for operation at extreme low temperatures. Silicone rubber is resistant to deterioration by weathering and by high-aniline-point petroleum-base oils and remains flexible over the temperature range noted. These products are not normally suitable for use in contact with low-aniline-point petroleum-base fluids, including fuels, due to excessive swelling.

Silicone (PVMQ) Rubber, Extreme-Low-Temperature Resistant, 75 - 85