49.025.40 橡胶和塑料 标准查询与下载

SAE AMS3198L-2014 中硬度氯丁海绵橡胶

This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, medium sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.

Sponge, Chloroprene (CR) Rubber, Medium Stiffness

SAE AMS3347C-2014 1200psi(8.27MPa)高模数硅酮橡胶.45-55

This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions and molded shapes. Primarily for parts required to operate or seal from -75 to +205 degrees C (-103 to +401 degrees F), compounded especially for high strength. Silicone elastomer is resistant to deterioration by weathering and by high-aniline-point-petroleum-base oils and remains flexible over the temperature range noted. These products are not normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling.

Rubber, Silicone 1200 Psi (8.27 Mpa), High Modulus 45-55

SAE AMS3323A-2014 闭孔海绵氟硅酮橡胶

This specification covers a fluorosilicone (FVM) rubber sponge in the form of sheet, strip, extrusions, and molded shapes.

Sponge, Fluorosilicone (FVM) Rubber, Closed Cell

SAE AMS3251J-2014 通用中型合成橡胶和软木合成物

This specification covers a synthetic rubber and cork composition in the form of sheet, strip, and molded shapes.

Synthetic Rubber and Cork Composition, General Purpose, Medium

SAE AMS3199L-2014 坚硬氯丁海绵橡胶

This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, firm sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.

Sponge, Chloroprene (CR) Rubber, Firm

SAE AMS3381-2014 非硅制飞机防火墙的密封化合物

This specification covers non-silicone synthetic rubber sealing compounds curing to elastomeric materials.

Sealing Compound, Aircraft Firewall, Non-Silicone

SAE AMS7274J-2014 飞机发动机燃油系统弹性密封用硬度为65至75的丁腈橡胶 (NBR)

This specification covers a butadiene-acrylonitrile (NBR) rubber in the form of molded rings. These rings have been used typically for sealing at temperatures as low as -55 degrees C (-67 degrees F) where resistance to hot petroleum-base lubricating oil is required, but usage is not limited to such applications.

Rubber, Butadiene-Acrylonitrile (NBR), 65 to 75 Hardness, For Elastomeric Seals in Aircraft Engine Oil Systems

SAE AMS3250K-2014 通用软质合成橡胶和软木合成物

This specification covers a synthetic rubber and cork composition in the form of sheet, strip, and molded shapes.

Synthetic Rubber and Cork Composition, General Purpose, Soft

SAE AS27195A-2014 AMS-R-7362丁腈橡胶槽模制的AMS4027, 6061-T6铝合金粘结密封

Scope is not available.

SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-R-7362

SAE AS27194B-2014 AMS-P-5315丁腈橡胶槽模制的AMS4027, 6061-T6铝合金粘结密封

Scope is unavailable.

SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-P-5315

SAE AMS7255D-2014 70-80耐液压机液体和合成油的四氟乙烯/丙烯(FEPM) 橡胶密封圈

This specification covers a tetrafluoroethylene/propylene rubber (FEPM) in the form of molded rings.

Rings, Sealing, Tetrafluoroethylene/Propylene Rubber (Fepm) Hydraulic Fluid and Synthetic Oil Resistance 70 to 80

SAE AMS7256B-2014 85-95耐液压机液体和合成油的四氟乙烯/丙烯(FEPM) 橡胶密封圈

This specification covers a tetrafluoroethylene/propylene rubber (FEPM) in the form of molded rings.

Rings, Sealing, Tetrafluoroethylene/Propylene Rubber (Fepm) Hydraulic Fluid and Synthetic Oil Resistant 85 to 95

SAE AMS3212P-2014 耐芳族燃料苯烯腈-丁二烯橡胶,55-65

This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.

Acrylonitrile Butadiene (Nbr) Rubber, Aromatic Fuel Resistant, 55-65

SAE AMS3226H-2014 耐热油和冷却剂的丁腈橡胶.低膨胀,45-55

This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for hose, packings, bushings, grommets, and seals in contact with hot, petroleum-base lubricating oils and glycol-type coolants from -40 degrees to +100 degrees C (-40 degrees to +212 degrees F).

Acrylonitrile Butadiene (Nbr) Rubber, Hot Oil and Coolant Resistant, Low Swell, 45-55

SAE AMS3208N-2014 不受天气影响45-55的氯丁二烯(CR)橡胶

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 45 - 55

SAE AMS3209M-2014 氯丁二烯(CR)耐风化橡胶65-75

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 65 - 75

SAE AMS3207N-2014 氯丁二烯(CR)耐风化橡胶25-35

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 25 - 35

DIN EN 2833-005:2014 航空航天系列. 玻璃纤维热固预浸渍物. 技术规范. 第005部分: 玻璃纤维/酚醛树脂预浸渍物; 德文和英文版本EN 2833-005-2013

Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 005: Glass fabric/phenolic resin preimpregnate; German and English version EN 2833-005:2013

SAE AMS3617E-2014 6-6 型聚酰胺 塑料成型件和挤出件

This specification covers one type of nylon thermoplastic resin in the form of moldings and extrusions.

Polyamide Type 6-6@ Plastic Moldings and Extrusions

DIN EN 2565:2013 航空航天系列.试验用碳纤维增强树脂板的制备.德文和英文版本EN 2565-2013

Aerospace series - Preparation of carbon fibre reinforced resin panels for test purposes; German and English version EN 2565:2013