49.030.01 紧固件综合 标准查询与下载

SAE AS18280/SUP 1A-2007 3000 psi液体连接的24°锥形非扩口配件(补充件1)

This supplement forms a part of the Aerospace Standard AS 18280 Fittings, 24?Cone, Flareless, Fluid Connection, 3000 psi, and shall be used to identify fitting standards citing this procurement specification.

Fittings, 24?Cone Flareless, Fluid Connection, 3000 psi (Supplement 1)

SAE AS5869A-2006 5080 Psi液压的轴向陷型的3孔法兰直通配件

FITTING ASSEMBLY, UNION, 3 HOLE FLANGE, AXIALLY SWAGED, HYDRAULIC, 5080 PSI FSC 4730.Table is about DIMENSIONS A THROUG FA, DIMESIONS J THROUGH S, DIMENSIONS W THROUGH W4A AND WEIGHTS.

Fitting Assembly, Union, 3 Hole Flange, Axially Swaged, Hydraulic, 5080 PSI

SAE AS5529-2006 内陷型非扩口管配件衬套

SLEEVE, FLARELESS TUBE FITTING, INTERNALLY SWAGED FSC 4730TABLE 1A-DIMENSIONS A-NTABLE 1B -DIMENSIONS L-Z AND WEIGHT

SLEEVE, FLARELESS TUBE FITTING, INTERNALLY SWAGED FSC 4730

SAE AS5793-2006 液动外螺纹直非扩口轴向陷型45度装配组件

This standard was prepared to provide envelope requirements for axially swaged, field attachable, tube fittings.

FITTING ASSEMBLY, STRAIGHT, MALE FLARELESS, AXIALLY SWAGED, HYDRAULIC FSC 4730

SAE AS5864-2006 闷头、24度锥形非扩口、液体连接、配件端的设计标准

This design standard is created to provide interface geometry for 3000 PSI flareless hydraulic fittings

FITTING END, BULKHEAD, 24?CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD FSC 4730

SAE AS5863-2006 24度锥形非扩口、液体连接、配件端的设计标准

This design standard is created to provide interface geometry for 3000 PSI flareless hydraulic fittings (SC)

FITTING END, 24?CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD FSC 4730

KS W ISO 7403-2005(2015) 航空 - 样车 - 形扳手米线

Aerospace－Spline drives－Wrenching configuration－Metric series

KS W ISO 7403:2005 航空航天.花键传动.扳手结构.米制系列

이 규격은 미터 계열에서 렌치 형상의 스플라인 드라이브의 치수를 규정한다. 이 규정은 설

Aerospace-Spline drives-Wrenching configuration-Metric series

SAE AS5827-2005 超精细螺纹、非扩口配件端部的设计标准

Fitting End, Flareless, Extra Fine Thread, Design Standard

SAE AS5828-2005 超精细螺纹、非扩口闷头配件端部的设计标准

FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD FSC 4730.Figure is about FITTING END DESIGN, STYLE G ; FITTING END DESIGN, STYLE JSAME AS STYLE H, EXCEPT AS SHOWN and FITTING END DESIGN, STYLE HSAME AS STYLE G, EXCEPT AS SHOWN. Table is about DIMENSIONS A-E, DIMENSIONS G-M, DIMENSIONS R-FF and DIMENSIONS GG-MM.

FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD FSC 4730

SAE ARP1135A-2004 液压或减速扭力扳手(用于50万英寸磅上限)驱动端标准化

This SAE Aerospace Recommended Practice (ARP) covers the dimensions of an inside splined driver-wrench adapter, envelope of the housing-wrench reaction, the mechanical method of adapting the driver-wrench adapter to the wrench adapter driven end, and the housing-wrench reaction to the holder-counter torque. The purpose of this recommended practice is to provide recommendations for the design of a series of components which, when used as prescribed, will provide a wrench capable of producing up to 500,000 in.-lb of torque.

Standardization of Drive End of Hydraulic or Geared Torque Wrenches for Use to an Upper Limit of 500,000 Inch Pounds

KS W ISO 3353-2:2003 航空航天.引导和收尾螺纹.第2部分:内螺纹

이 규격은 항공 우주 구조물에 사용되는 암나사산(관통되지 않은 나사 구멍)에 대한 초입

Aerospace－Lead and runout threads－Part 2：Internal threads

KS W ISO 3353-2-2003(2023) 航空航天导螺纹和跳动螺纹第2部分:内螺纹

Aerospace－Lead and runout threads－Part 2：Internal threads

KS W ISO 3353-2-2003(2018) 航空航天铅和跳动螺纹第2部分:内螺纹

Aerospace－Lead and runout threads－Part 2：Internal threads

SAE J2655-2003 垫圈和缩减垫圈的紧固件零件标准(英制尺寸规格)

This SAE Part Standard covers selected inch dimensioned washers and lock washers manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever washers of the covered materials are used. This standard permits the washers to be identified and ordered by a part of identifying number (PIN) as defined in this standard. The purpose of this document is to assist the designer and other personnel in providing requirements and part or identifying numbers for the most commonly used washers and lock washers. A part or identification number (PIN) is normally required for all military applications and provides a useful means of communicating washer and lock washer requirements to suppliers and manufacturers in a very succinct manner.

Fastener Part StandardWashers and Lockwashers (Inch Dimensioned)

SAE AS5449-2003 短锥形焊接环的配件端的设计标准

FITTING END, WELD RING, SHORT TAPERED, DESIGN STANDARDFIGURE 1 – FITTING END, WELD RINGTABLE 1A – DIMENSIONS (INCH)TABLE 1B - DIMENSIONS (MILLIMETER)

FITTING END, WELD RING, SHORT TAPERED, DESIGN STANDARD

SAE ARP4988-2003 止推金属丝长度和最小嵌件深度确定规程

The scope of this ARP is to define methods of determining wire lengths and minimum insertion depths of thrust wires used for retaining components together. The equations presented herein were developed for use with hexagonal nuts. If an exterior configuration other than hexagon is used, adjustments to the minimum insertion depth equation would be required.

Procedure for Determining Thrust Wire Lengths and Minimum Insertion Depths

SAE AS5170-2003 O形密封环直螺纹端口插头接头

FITTING, PLUG, PORT, STRAIGHT THREAD, O-RING SEALTABLE 1-CIMENSIONS AND WEIGHTS

FITTING, PLUG, PORT, STRAIGHT THREAD, O-RING SEAL

SAE AS7365/7-2003 12英寸空气管道的外螺纹接头箍

BAND, MALE COUPLING, 12 INCH AIR DUCT

BAND, MALE COUPLING, 12 INCH AIR DUCT

SAE AS7365-2003 350℉低压金属加固调节空气磨光风道总成

This Aerospace Standard (AS) defines the requirements for a metallic reinforced, duct assembly suitable for use in low pressure, 350°F ground heaters.

Duct Assembly, Ground, Conditioned Air, Metallic Reinforced, Low Pressure, 350 Degrees F