49.030.01 紧固件综合 标准查询与下载

SAE AS7365/1-2003 针型阴螺纹接头

PIN, FEMALE COUPLING

PIN, FEMALE COUPLING

SAE AS7365/8-2003 6英寸空气管道的内螺纹接头箍

BAND, FEMALE COUPLING, 6 INCH AIR DUCT

BAND, FEMALE COUPLING, 6 INCH AIR DUCT

SAE AS172321A-2003 航空用UNS G41400型扳手螺母

No scope available.

Nut, Spanner, Aeronautical UNS G41400

SAE AS172236A THRU AS172270A-2003 航空用UNS G41400扳手锁紧螺母

Nut, Spanner, Bearing Retaining, Aeronautical, UNS G41400

Nut, Spanner, Bearing Retaining, Aeronautical, UNS G41400

SAE AS172321A THRU AS172370A-2003 航空用UNS G41400扳手螺母

Nut, Spanner, Aeronautical UNS G41400

Nut, Spanner, Aeronautical UNS G41400

SAE AS5229-2003 气压连接用内直螺纹管口的设计标准

PORT, INTERNAL STRAIGHT THREAD, AIR CONNECTION, DESIGN STANDARDFIGURE 1 - PORT, INTERNAL STRAIGHT THREAD

PORT, INTERNAL STRAIGHT THREAD, AIR CONNECTION, DESIGN STANDARD

SAE J2277-2003 喷丸覆盖率

This SAE Recommended Practice provides procedures for determining shot penning coverage. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage may be detrimental to fatigue.

Shot Peening Coverage

SAE AIR5575-2002 针对航空航天器应用的火印线号

This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process. Although prominent members of the aerospace community are taking aggressive measures to phase out the hot stamping of interconnecting wire, the process lingers on, particularly within the operations of smaller manufacturers, modification shops, and operator maintenance facilities. In recent years, non-impact marking processes have been developed that can mark virtually all of the common wire types used in aerospace interconnect applications. The purpose of this document is to encourage full conversion to non-impact marking processes in order to reduce the probability of causing damage to the wire insulation.

Hot Stamp Wire Marking Concerns for Aerospace Vehicle Applications

KS W 1553-2001(2011) 航空 - 样车 - 形扳手米线

Aerospace－Spline drives－Wrenching configuration－Metric series

SAE AIR1551A-2001 扭矩拧紧公制螺钉紧固件

The purpose of this Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for threaded fasteners when a common torque value per fastener size is the objective. (The fasteners are based on the dimensional data in MA1518). It also provides a series of curves that show the effect of the coefficient of friction on the axial load produced in a fastener, when the recommended torques are applied.

Torque Tightening Metric Screw Threaded Fasteners

KS W 1534-1999(2014) 六角扳手服装驱动器 - 航空航天

Aerospace－Bihexagonal drives－Wrenching configuration－Metric series

HB 7595-1998 使用温度不高于４２５°Ｃ ＭＪ螺纹自锁螺母通用规范

本规范规定了使用温度不高于425℃MJ螺纹自锁螺母技术要求、试验方法和检验规则。 　　本规范适用于航空结构用的，使用温度不高于425℃MJ螺纹自锁螺母。

General specifications for self-locking nut with ＭＪthread and operating temperature no more than 425°Ｃ

BS A 323:1998 十二角驱动.扳手外形.公制系列

This International Standard specifies the metric wrenching configuration dimensions of bihexagonal drives. This is a design standard.

Bihexagonal drives - Wrenching configuration - Metric series

ISO 4095:1998 航空航天 十二角传动 扳手结构 米制系列

This International Standard specifies the metric wrenching configuration dimensions of bihexagonal drives. This is a design standard.

Aerospace - Bihexagonal drives - Wrenching configuration - Metric series

SAE AS7113-1997 针对紧固件制造的国家航空航天和国防承包商认证计划要求

This Aerospace Standard (AS) establishes the requirments for manufacturers of Fasteners to be accredited by the National Aeroapce and Defense Contractors Accreditation Program (NADCAP). NADCAP accreditation is granted in accordance with SAE AS7003 after demonstrating compliance with the requirements herein. These requirements may be supplemented by additional requirements specified by NADCAP Fastener Manufacturing Task Group. Using the corrsponding Audit Criteria checklists (PRI ACs) will ensure that accredited Fastener Manufacturing suppliers meet all of the requirements in this standard and all applicable supplementary standards.

National Aerospace and Defense Contractors Accreditation Program Requirements for Fastener Manufacturing

SAE AS870D-1997 12角传动扳手结构的设计标准

Wrenching Configuration, Bi-Hexagonal (12-Point), Drive, Design Standard For / Note: Approved 2006-05-00, 2001-11-00, 1995-05-00.

(R) Wrenching Configuration, Bi-Hexagonal (12 Point) Drive, Design Standard for FSC 5120

SAE ARP953B-1996 紧固件的应力顶层

This document establishs limits or parameters for designing bolt heads with proper control of flowlines to assure sufficient strength to resist stresses induced by static or dynamic loads without being affected by lightening and lockwire holes.

Stress Dome in Fasteners

BS EN 3611:1995 套筒.尺寸和配合选择.设计标准

This standard specifies the dimensions and fit selection of tight fitting spigots for locating casings and other major components for aerospace applications.

Spigots - Dimensions and fit selection - Design standard

NF L20-026*NF EN 3611:1995 航空航天系列.插销.尺寸和配合的选择.设计标准

Aerospace series. Spigots. Dimensions and fit selection. Design standard.

SAE MA4535-1995 公制薄壁高强度盒型开口端组合12点扳手

This SAE Metric Aerospace Standard (MA) provides dimensional, performance, testing and other requirements for high strength, thin wall, double head box and combination wrenches which possess an internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the apex of the fasteners wrenching points. This standard provides additional requirements beyond ANSI B107.9 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes

Wrenches, Box and Open End Combination Twelve Point, High Strength, Thin Wall, Metric