49.030.01 紧固件综合 标准查询与下载
共找到 123 条与 紧固件综合 相关的标准，共 9 页
This document specifies the dimensions and fit selection of tight fitting spigots for locating casings and other major components.
Aerospace series - Spigots - Dimensions and fit selection; design standard; German version EN 3611:1995
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1995-08
- 实施
This standard specifies theother major components fordimensions and fit selection of tight fitting spigots for locating casings andaerospace applications.
Aerospace series - Spigots - Dimensions and fit selection - Design standard
- ICS
- 49.030.01
- CCS
- 发布
- 1995-01-01
- 实施
This SAE Aerospace Standard (AS) covers high strength thin wall commercial sockets, universal sockets, box wrenches and torque adapters which possess the strength, clearances, and internal wrenching design so configured that, when mated with 12-point fasteners conforming to the requirements of AS 870, they shall transmit torque to the fastener without bearing on the outer 5% of the fasteners wrenching points
Wrenches, Hand Twelve Point High Strength, Thin Wall
- ICS
- 49.030.01
- CCS
- 发布
- 1994-01-01
- 实施
This SAE Aerospace Standard (AS) covers 12-point open box end crowfoot, flare nut, double box end, combination box and open box end, and ratcheting open box end wrenches that are designed with the following requirements: a. non-distorting usage, b. possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 AP80, and c. transmitting torque to tube fittings without bearing on the apex of fitting wrenching points.
Wrenches; Flare Nut, Crowfoot, 12-Point Nondistorting
- ICS
- 49.030.01
- CCS
- 发布
- 1993-03-31
- 实施
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current inspection of open fastener holes in aluminum aircraft structures. This process has been used typically by maintenance and overhaul facilities personnel to inspect aluminum aircraft structures for service-induced cracks, but usage is not limited to such applications.
Eddy Current Inspection of Open Fastener Holes in Aluminum Aircraft Structure
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1992-04-01
- 实施
本标准规定了ＭＪ螺纹滚制前毛坏直径尺寸与公差，并给出了毛坏直径尺寸的计算方法。 本标准适用于采用全牙型ＭＪ螺纹滚丝轮滚制的螺栓。对于管路件和结构可参照使用。
Blank diameter before MJ thread rolling
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1990-09-18
- 实施
- 1990-12-01
Aéronautique et espace - Équipements - Choix des éléments de fixation, série NF E.
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1989-05
- 实施
- 1989-04-20
本标准是按GB196-81《普通螺纹 基本尺寸》及GB2516-81《普通螺纹偏差表》而给出的《切制外螺纹前的光杆直径及偏差》。
Shank diameter and deviation before cutting out external screw thread
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1987-06-27
- 实施
- 1988-01-01
Aerospace; fasteners for aerospace construction, bi-hexagonal wrenching configuration
- ICS
- 49.030.01
- CCS
- V95;V20
- 发布
- 1980-12
- 实施
This is a design standard not to be used as a part number.
Wrenching Configuration, 12 Spline, for Metric Threaded Fasteners
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1980-04-01
- 实施
BS A273 describes the principles of flushness control and the recommended gauging practice for 100° countersunk head fasteners.
Specification for gauging practice for 100 ° countersunk head fasteners for flushness control
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 1978-01-31
- 实施
- 1978-01-31
This British Standard specifies the dimensions of the Hi-torque speed drive recess and of the driver tip envelope.
Specification for Hi-torque speed drive recess: dimensions and gauging for countersunk head fasteners
- ICS
- 49.030.01
- CCS
- J13
- 发布
- 1977-04-29
- 实施
- 1977-04-29
本标准规定的通孔尺寸适用于带有安装间隙的普通螺栓、螺钉和螺桩。
Through hole dimensions for bolts, screws and studs
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 实施
本标准规定了保险孔（锁紧丝孔）的型式、尺寸、极限偏差及加工保险孔用工艺孔的型式、尺寸和极限偏差。 本标准适用于紧固连接用六角螺母、六角头螺栓、螺钉和管路连接用六用形外套螺母、螺塞及管接头。
Security hole for hexagonal parts
- ICS
- 49.030.01
- CCS
- V20
- 发布
- 实施
