共找到 2326 条与 航空航天制造用零部件 相关的标准,共 156 页
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
Aircraft Jacking Pads Adapters and Sockets Design and Installation of
Scope is unavailable.
ADAPTER, FLARELESS TUBE, BULKHEAD AND UNIVERSAL TO FLARED TUBE
Scope is unavailable.
SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROCARBON RUBBER, AMS7276
Scope is unavailable.
BEARING, PLAIN, ROD END, SELF-ALIGNING, SELF-LUBRICATING, NARROW, EXTERNALLY THREADED, -65 TO +325 °F
This specification covers metallic-encased gaskets with and without inlays.
Gasket, Metallic-Encased
Scope is unavailable.
FITTING ASSEMBLY, PLUG, RING LOCKED PORT CONNECTION, 4000 PSI AND 5000 PSI
Scope is unavailable.
INSERT - THIN WALL, SHORT AND LONG HOLE PREPARATION FOR
This document establishes standard gland dimensions for low pressure static radial O-ring seal applications and provides recommendations for modifying these glands in special applications. No provisions are made in this document for anti-extrusion devices.
Gland Design, Elastomeric O-Ring Seals, Static Radial and Face 800 psi Maximum Service
Scope is unavailable.
TUBING, FLARED, STANDARD DIMENSIONS FOR, DESIGN STANDARD
This SAE Aerospace Standard (AS) establishes the requirements for self-aligning, self-lubricating plain spherical bearings incorporating polytetrafluoroethylene (PTFE) in a liner between the ball and the outer race for use in a temperature range of -65 to +250 °F (-54 to +121 °C).
Bearings, Plain and PTFE Lined, Self - Aligning
This standard establishes the inspection requirements and acceptance standards for optimum surface finish O-ring packings and gaskets. (This is not an O-ring specification per se). This standard must be used in conjunction with an O-ring drawing and/or material specification. This standard is to be specified only where stringent performance requirements are necessary.
Top Visual Quality (TVQ) O-ring Packings and Gaskets - Surface Inspection Guide and Acceptance Standard
Scope is unavailable.
BRACKET, ANGLE, 90°, CADMIUM PLATED, STEEL, UNS G41300, .190 BOLT
This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available.
Aerospace Size Standard for O-rings
Aerospace series - Rod ends, with self-aligning double row ball bearings and threaded shank in steel - Inner ring and balls in corrosion resisting steel - Dimensions and loads - Inch series; German and English version DIN EN 4156:2013
Scope is unavailable.
BRACKET, ANGLE 90°, CADMIUM PLATED, ALLOY STEEL UNS G41300, .190 X .375 BOLT
Scope is unavailable.
BRACKET, ANGLE, 90° .190 BOLT
Scope is unavailable.
BRACKET, ANGLE, 90° .190 X .375 BOLT
Aerospace series - Bushes, flanged in corrosion-resisting steel with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series; German and English version EN 4537-2:2009
Aerospace series. Rod ends, with self-aligning double row ball bearings and threaded shank in steel. Inner ring and balls in corrosion resisting steel. Dimensions and loads. Inch series
Aerospace-Accessory drives and mounting flanges(Metric series)-Part 1:Design criteria
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号