53.020.30 起重设备附件 标准查询与下载

ISO 16625:2013 起重机和卷扬机.钢丝绳,鼓和滑车轮筛选

This International Standard specifies the minimum practical design factors, Zp, for the various classifications of mechanism, rope types, rope duties and types of spooling and demonstrates how these are used in the determination of the minimum breaking force of the wire rope.

Cranes and hoists - Selection of wire ropes, drums and sheaves

DIN ISO 4309:2013 起重机.绳索.保养和维护、检修和报废(ISO 4309-2010)

Cranes - Wire ropes - Care and maintenance, inspection and discard (ISO 4309:2010)

YB/T 089-2013 冶金吊具

本标准规定了冶金行业专用吊具的术语、分类、基本参数、型号表示方法、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于冶金行业专用成台非吸盘类吊具(以下简称吊具),包括钢锭吊具、板坯吊具、方坯吊具、钢卷吊具、钢板吊具、型材吊具、轧辊吊具、设备吊具等。

Metallurgy load-lifting attachment

JB/T 7333-2013 手动起重用夹钳

本标准规定了典型结构手动起重用夹钳的分类和标记、基本参数和尺寸、技术要求、试验方法、检验规则、使用以及标志、包装、运输及贮存。本标准适用于起吊钢板、圆钢、钢轨及工字钢等一般用途的手动起重用夹钳(以下简称手动夹钳)。其他相似用途的手动夹钳可参照使用。

Hand powered lifting clamps

JB/T 7019-2013 工业制动器 制动轮和制动盘

本标准规定了鼓式制动器用制动轮(以下简称制动轮)和盘式制动器用制动盘(以下简称制动盘)的型式和公称尺寸、技术要求、试验方法、检验规则、标志、包装、运输与贮存。本标准适用于JB/T 6406和JB/T 7685中规定的鼓式制动器用制动轮及JB/T 7020和JB/T 10917中规定的盘式制动器用制动盘,圆盘式制动器用制动盘可参照本标准执行。

Industrial brake.Brake drums and discs

GSO ISO 2262:2013 与钢丝绳一起使用的通用环（套管） 规格

This International Standard specifies the requirements for general purpose thimbles suitable for use with steel wire ropes complying with IS0 2408, having a maximum tensile grade of 1 770 MPa(N/mm2), with diameters from 4 to 60 mm. It does not apply to thimbles for use with fibre ropes. Reeving thimbles and solid thimbles are not included.

General purpose thimbles for use with steel wire ropes -- Specification

GSO ISO 3075:2013 用于起重用途的短环链 S级（6）非校准 用于链条吊索等

Abstract Specifies the requirements for lifting chains, grade S (6), non-calibrated, for use on cranes, in chain slings and for general lifting purposes. These are electrically welded round steel short link chains, fully heat treated and tested complying with ISO 1834. The range of sizes covered is from 5 to 45 mm. The annex gives a range of temporary additional sizes 6 to 30 mm.

Short link chain for lifting purposes -- Grade S (6) non calibrated, for chain slings etc.

GSO ISO 3077:2013 用于起重用途的链条中的小链节 T 级（T-DAT-DT 类型）和起重链中的公差

  Scope is not provided for this standard

Short-link chain for lifting purposes -- Grade T, (types T, DAT and DT), fine-tolerance hoist chain

GSO ISO 3056:2013 起重链中未经校准的圆钢链环 使用和维护

Abstract This second edition cancels and replaces the first edition (ISO 3056:1974), of which it constitutes a technical revision. Constitutes a guide to the selection, use, inspection, testing, maintenance and repair of non-calibrated, round steel, short link chains and chain slings. Lifting chains and chain slings may be governed by national and local laws and regulations.

Non-calibrated round steel link lifting chain and chain slings -- Use and maintenance

ISO 7597:2013 带闩锁的锻钢吊钩,8级

This International Standard specifies requirements for forged steel lifting hooks with latch of grade 8 having eye or clevis and pin up to 63 t working load limit (WLL), mainly: — for use in chain slings according to ISO 4778 and ISO 7593; — for use in steel wire rope slings according to ISO 7531; — for use in textile slings; — intended for lifting objects, materials or goods. This International Standard does not apply to hand forged hooks. Annex A gives the bases for calculation of hook dimensions. Annex B gives an example of a designation system for hooks of grade 8.

Forged steel lifting hooks with latch, grade 8

JIS B 8815:2013 电动链式提升机

Electric chain hoists

DIN 5684-3:2013 圆钢环节链. 精密公差吊链. 第3部分:T级 (T型, DAT型和DT型)

Round steel link chains - Fine tolerance hoist chains - Part 3: Grade T (Types T, DAT and DT)

VDI 2358-2012 机械搬运设备用钢丝绳

The guideline deals with the rope technology terms, the most useful kind of ropes, the rope choice, application and calculation of ropes as weil as their behaviour in test and practical use. Further the discard state caused by broken wires, wear, corrosion and other rope damages will be considered. Also attention will give to the most important standards and safety regulations.

Wire ropes for mechanical handling equipment

ABNT NBR 13545 EN-2012 起重目的 - 卸扣

This Standard specifies the general characteristics, performance and critical dimensions necessary for interchangeability and compatibility with other components, of forged dee and bow shackles in a range of sizes having working load limits from 0,32 to 320 t, and in grades 4, 6, 8, 8S, R4 and 10.

Lifting purposes - Shackles

ISO 3076:2012 用于一般提升目的的圆钢制段环链.吊链用吊链中等公差.8级

This International Standard specifies the requirements for medium tolerance sling chains of grade 8 for use in chain slings and for general lifting purposes. They are round steel short link chains (3 dn), electrically welded, heat treated and tested; they comply with the general conditions of acceptance of ISO 1834. NOTE 1 Butt welding and flash butt welding are listed in ISO 4063. The range of nominal sizes covered by this International Standard is from 4 mm to 45 mm. They are for use in the temperature range –40 °C to +400 °C. NOTE 2 Concerning the use and maintenance of chain slings of grade 8, see ISO 3056.

Round steel short link chains for general lifting purposes - Medium tolerance sling chains for chain slings - Grade 8

DS/EN 13411-4:2012 钢丝绳的端接 安全 第4部分：金属和树脂套接

This European Standard specifies the minimum requirements for the molten metal and resin socketing of steel wire ropes within the scopes of EN 12385-4:2002+A1:2008; EN 12385-5:2002; EN 12385-6:2004; EN 12385-7:2002; EN 12385-8:2002; EN 12385-9:2002 and EN 12385-10:2003+A1:2008. The European Standard is applicable only to those requirements that ensure that the socketing is strong enough to withstand a force of at least 100 % of the minimum breaking force of the rope (i.e. socket termination efficiency factor KT = 1,0).NOTE Rope terminations made by socketing in accordance with this European Standard can be used for determining the breaking force of wire rop

Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing

DS/EN 13411-8:2012 钢丝绳的端接 安全 第8部分：型锻端子和型锻

This European Standard specifies the minimum requirements for swage terminals and the securing of such terminals by a swaging process to carbon steel rope conforming to EN 12385-4 and EN 12385-5, spiral strand rope conforming to EN 12385-10 and stainless steel stranded rope.This European Standard is not applicable to spiral rope incorporating full lock wires - see EN 12385-10 -, nor ropes with coverings and /or fillings (see 3.6.3 of EN 12385-2:2002+A1:2008).This European Standard is applicable to swaged terminations that have a terminal efficiency factor, KT, of at least 0,9 and are used as part of a wire rope accessory such as a sling, or wire rope assemb

Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging

GSO EN 1492-4:2011 织物吊索 安全 第4部分：天然纤维和合成纤维绳制成的通用吊索

This European Standard specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless slings, with or without fittings, made of sisal, hemp and manila 3- and 4-strand laid construction natural fibre ropes and polyamide, polyester and polypropylene 3- and 4-strand laid construction and 8-strand plaited construction man-made fibre ropes having a reference number in the range of 16 to 48 inclusive. The fibre rope slings covered by this part of EN 1492 are intended for general purpose lifting operations, i.e. when used for lifting objects, materials or goods which require no deviations from the requirements, safety factors or working load limits specified. Lifting operations not covered by this standard would include the lifting of persons, potentially dangerous materials such as molten metal and acids, glass sheets, fissile materials, nuclear reactors and where special conditions apply. Fibre rope slings conforming to this European Standard are suitable for use and storage in the following temperature ranges: a) polyester and polyamide -40 °C to 100 °C, b) manila, sisal, hemp and polypropylene -40 °C to 80 °C. This European Standard does not apply to fibre rope sling assemblies rated by the trigonometric method. This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the use of fibre rope slings when carried out in accordance with the instructions and specification given by the manufacturer or authorized representative.

Textile slings - Safety - Part 4: Lifting slings for general service made from natural and man-made fibre ropes

GSO EN 13414-3:2011 钢丝绳吊索 安全 第3部分：带孔眼和编织电缆的吊索

This European Standard specifies the construction requirements, calculation of WLL, testing and certification of steel wire rope grommets, cable-laid grommets and cable-laid slings using strand and wire rope conforming to EN 12385-4. The hazards covered by this standard are identified in clause 4. This standard covers ferrule-secured cable-laid slings up to 60mm.

Steel wire rope slings - Safety - Part 3: Grommets and cable-laid slings

JB/T 11209-2011 流动式起重机.滑轮

本标准规定了流动式起重机常用滑轮的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于GB/T 6974.2定义的流动式起重机上的钢丝绳滑轮。

Mobile cranes.Sheaves