55.020 货物的包装和调运综合 标准查询与下载

EN ISO 14375:2023 药品的儿童防护不可再封闭包装.要求和试验

This document specifies performance requirements and methods of test for non-reclosable packaging that have been designated child-resistant. This document is intended for type approval only (see 3.5) and is not intended for quality assurance purposes.

Child-resistant non-reclosable packaging for pharmaceutical products - Requirements and testing (ISO 14375:2018)

EN ISO 28862:2023 包装.儿童防护包装.非药品用不可再封闭包装的要求和试验程序

This document specifies performance requirements and methods of test for non-reclosable packaging that has been designated child-resistant and which is intended to contain non-pharmaceutical products. This document is intended for type approval only (see 2.5) and is not intended for quality assurance purposes. This document applies to non-reclosable packages of the single-use type consisting of one or more individual units. Non-reclosable packages for pharmaceutical products are excluded from the scope of this document. These are the subject of a separate standard, ISO 14375, Child-resistant non-reclosable packaging for pharmaceutical products — Requirements and testing.

Packaging - Child-resistant packaging - Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products (ISO 28862:2018)

T/ZS 0463-2023 商品过度包装检验规范 食品和化妆品

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  要求　 4.1  包装空隙率　 4.2  包装层数　 4.3  包装成本　 4.4  混装要求　 5  样本抽取　 5.1  抽取方法　 5.2  抽样数量　 6  检验　 6.1  测量设备　 6.2  销售包装体积测量方法及包装空隙率计算　 6.3  包装层数计算　 6.4  包装成本与销售价格比率计算　 6.5  原始记录　 6.6  数据处理　 7  结果评定与报告　 7.1  评定准则　 7.2  检验报告　 附录A（资料性）手动法销售包装测量补充说明　 附录B（资料性）手动法包装空隙率的检验步骤　 附录C（规范性）食品和化妆品包装检验原始记录表　 附录D（规范性）食品和化妆品包装检验报告　 参考文献　

Operating procedure of Testing for excessive Package Food and Cosmetics

ASTM D4919-23 危险材料（危险货物）包装试验的标准指南

1.1 This guide identifies the key information required for United Nations (UN) packaging certification to ensure the selected packaging will be certified to the appropriate level for its intended use and provides guidance for locating relevant sections of the United States Department of Transportation Title 49 Code of Federal Regulations (CFR). Consult with a regulatory specialist whenever needed. 1.2 This guide provides assistance in determining the appropriate performance tests required to certify packaging designs to the United States Department of Transportation Title 49 Code of Federal Regulations performance oriented packaging standards based on the United Nations Recommendations on the Transport of Dangerous Goods.. 1.3 This guide covers the testing for transportation of hazardous materials (dangerous goods) packagings for net masses not exceeding 400 kg (880 lb) or capacities not exceeding 450 L (119 gal), excepting packagings for infectious substances, radioactive materials, cylinders and other receptacles for gases. 1.4 This guide does not replace domestic or international regulatory requirements for hazardous materials packaging but is strongly recommended to be used in conjunction with those regulations. 1.5 The user of this guide must be trained in accordance with the United States Department of Transportation Title 49 Code of Federal Regulations (49 CFR) as required by 172.700 and should be familiar with other applicable hazardous materials regulations such as: International Civil Aviation Organization (ICAO) Technical Instructions for the Safe Transport of Dangerous Goods by Air, and the International Maritime Dangerous Goods Code (IMDG Code) and carrier rules such as International Air Transport Association (IATA) Dangerous Goods Regulations. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Testing of Hazardous Materials (Dangerous Goods) Packagings

ASTM D8135-17(2023) 经过联合国性能试验的包装用替代品、无害颗粒固体填充物质的选择标准指南

1.1 The purpose of this guide is to clarify the selection, use, and description criteria of non-hazardous particulate solid substitutes used to replace hazardous materials for the purpose of performance testing packagings. This includes identification of the physical parameters of substitute non-hazardous solid test fill materials that may affect packaging performance and test results and should be considered when selecting and describing a test fill material that conforms to the requirements of the Hazardous Materials Regulations (HMR). This guide is intended for use with package testing procedures for particulate solid materials that have flow characteristics. It is not intended for use with hazardous articles. 1.2 This guide provides information to assist packaging users, manufacturers, and performance testing service suppliers regarding the types of physical properties that should be considered when selecting substitute filling substances for the testing, certification and manufacture of packagings under the United Nations packaging protocols (UN Recommendations on the Transport of Dangerous Goods-Model Regulations) as adopted by US DOT in 49 CFR HMR. 1.3 This guide provides the suggested minimum information concerning the physical characteristics of the filling substances that should be documented in the certification test report and notification to users to allow for test repeatability and analysis, and to provide guidance to the user of a packaging of pertinent physical differences between potential hazardous lading and the filling substance with which the packaging was tested. 1.4 This guide does not purport to address regulatory requirements regarding the compatibility of filling substances with transport packagings. Compatibility requirements must be assessed separately, but it should be noted that under certain national and international dangerous goods regulations, the selection of the filling substances for package performance testing may be prescribed with respect to chemical compatibility requirements. NOTE 1—Under the US HMR determination of packaging compatibility with a particular hazardous fill material is “the responsibility of the person offering the hazardous material for transportation” as prescribed in 49 CFR § 173.24(e). 1.5 When testing packaging designs intended for hazardous materials (dangerous goods), the user of this guide shall be trained in accordance with 49 CFR §172.700 and other applicable hazardous materials regulations such as the ICAO Technical Instructions, IMDG Code, other applicable national or international dangerous goods regulations that govern the testing, manufacture and use of packagings authorized for the transportation of dangerous goods, and carrier rules such as the IATA Dangerous Goods Regulations. 1.6 The units of measurement are consistent with the HMR. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection of Substitute, Non-hazardous, Particulate Solid Filling Substances for Packagings Subjected to the United Nations Performance Tests

T/NCHP T/NCHP003-2023 “定兴太平萝卜”储藏运输及包装标识规范

本标准规定了“定兴太平萝卜”的商品质量基本要求、包装、标识和流通过程要求。 本标准适用于“定兴太平萝卜”流通的经营和管理。

Specification for storage, transportation, and packaging labeling of "Dingxing Taiping Radish"

ISO 23416:2023 良好分销中对温度敏感的药品包装的一般规范和试验方法实践原则

This document describes the general specifications of temperature-sensitive medicinal packaging based on the principles of good distribution practice (GDP). It also specifies test methods to validate the package performance for temperature-sensitive medicinal products. This covers the procedures of temperature-recording and testing methods on the performance of insulated containers such as dimensions, weights, storage capacity and robustness in temperature-controlling. This document does not guarantee the quality and safety of all medicinal products. Under special circumstances where the weight or the characteristics of the products and environment show specific conditions, agreements are followed. This document does not cover the active packaging system, but only covers the passive packaging system able to control the desired temperature without any power sources.

General specifications and testing methods for temperature-sensitive medicinal packages in good distribution practice principles

KS T 1303-2022 商业包装（消费包装）空间体积与总包装体积之比的测定

Determination of ratio of spatial volume to total packaging volume for commercial packaging(consumer packaging)

KS M ISO 5626-2022 纸.耐折性的测定

Paper — Determination of folding endurance

KS M ISO 5626:2022 纸.耐折性的测定

Paper — Determination of folding endurance

KS T 1014-2022 缝合牛皮纸袋通则

General rules for sewn kraft paper sacks

DB43/T 2529-2022 可循环快递包装应用规范

Application specification for recyclable express packaging

KS T 1205-2022 手持式包装的手孔设计原则和测试方法

Hand hole design principles and test methods for handheld packages

DB3401/T 270-2022 药品销售退货服务规范

Drug sales return service specification

T/SHDSGY 053-2022 环保树脂球形关节人偶生产技术规范

本标准规定了环保树脂球形关节人偶生产技术规范的分类、技术要求、试验方法、检测规则、标志、包装、运输、贮存。 本文件适用于本行业内以环保树脂为主要材料制成的球形关节人偶

Technical specification for production of environmental protection resin spherical joint doll

GSO ISO 22982-1:2022 运输包装 用于包裹运输的温控运输包装 第1部分：一般要求

This document specifies the general requirements of transport packaging, especially the containers, which are formed or prepared for the temperature-controlled transport services of parcel shipping. Safety or sanitation is not covered in this document. This document set outs the general requirements for transport packaging for safe storage and distribution of temperature-sensitive products.

Transport packaging — Temperature-controlled transport packages for parcel shipping — Part 1: General requirements

GSO ISO 22982-2:2022 运输包装 用于包裹运输的温控运输包装 第2部分：测试通用规范

This document specifies the test methods of temperature-controlled packages for parcel shipping. Tests include physical, thermal conductivity and insulation performances of transport packages that use insulation for the purpose of blocking thermal conduction between the inside and the outside of a product package that need temperature control.

Transport Packaging — Temperature controlled transport packages for parcel shipping — Part 2: General specifications of testing

ASTM D7860-14(2022) 使用自动扭矩测试设备测量带连续螺纹封闭的防儿童和非防儿童包装的扭矩保持力的标准试验方法

1.1 These test methods evaluate the torque retention of continuous thread closures on containers with matching finishes, for predetermined environmental conditions over time. Methods are defined for both Type I, style “A” push down and turn Type II2 child resistant and non child resistant type closures. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. NOTE 1—The SI unit system is the recommended system. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Measurement of Torque Retention for Child Resistant and Non-Child Resistant Packages with Continuous Thread Closures Using Automated Torque Testing Equipment

T/RAJJ 004-2022 融安金桔 包装、储运规范

本标准规定了融安金桔采收质量要求、储藏、包装、标志、装箱及运输规范。 本标准适用于融安金桔的包装和储运。

Rongan kumquat Packaging, storage and transportation specifications

T/ZPP 023-2022 共享循环物流塑料托盘

本文件规定了共享循环物流塑料托盘的术语和定义、产品分类、基本要求、技术要求、检验方法、 检验规则、标志、包装、运输和贮存及质量承诺技术要求。 本文件适用于共享循环物流FDY、POY、DTY等塑料托盘。

Shared circular logistics plastic pallet