55.180.99 有关货物调运的其他标准 标准查询与下载

T/YNLTX 001-2020 羊肉冷链物流操作规程

本标准规定了羊肉冷链物流的术语和定义、基本要求、操作流程、包装与标识。

Mutton cold chain logistics operating procedures

ASTM F2325-14(2020) 多层钢（MLS）和其他金属层垫圈的运输应用标准分类

1.1 This classification covers a means for specifying MultiLayer Steel (MLS) and other Metal Layer Gaskets for Transportation Applications by application and construction. These structures are composed of one or more steel or metal layers of material, which may have coatings or embossments. Commercial materials designated as composite or enveloped gaskets are excluded from this classification and are covered by Classification F868 and Practice F336, respectively. 1.2 Since all of the properties that contribute to gasket performance are not included, use of this classification as a basis for selecting an MLS or Metal Layer gasket is limited. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Multi-Layer Steel (MLS) and Other Metal Layer Gaskets for Transportation Applications

T/ZAII 017-2019 智能自提柜

本标准规定了智能自提柜的术语和定义、缩略语、要求、试验方法、质量评定程序以及标志、包装、运输、贮存等。

Intelligent Parcel Locker

ASTM E2463-19 货舱床盖（CBC）的标准性能规格M105A2拖车 II型

1.1 This specification covers the general performance requirements for the Type II Cargo Bed Cover (CBC). The Type II Cargo Bed Cover is a removable general purpose rigid wall enclosure that is mounted on the M105A2 Trailer, Cargo: 1.5 Ton, 2 Wheel. The Type II CBC provides environmental protection and security for mission equipment and items of general transport. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Cargo Bed Cover (CBC) M105A2 Trailer, Type II

ASTM E2462-18 I型货舱床罩（CBC）HMMWV的标准性能规范

1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit, M1037, M1042, M1097, and M1113 HighMobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides environmental protection and security for mission equipment and items of general transport. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I

T/CPF 0002.5-2018 储备物资的包装、标识、堆码和存储 第5部分：天然橡胶

本标准规定了天然橡胶的包装方式、标识内容、码垛方式和存储要求。适用于天然橡胶的包装、标识、码垛和存储。 由于天然橡胶储备物资为有机物，与其他金属储备物资有很大的不同，因此特别列为一个标准。主要以金属架存储和堆码的方式进行。

Packaging, marking, stacking and storage of reserves - Part 5: Natural rubber

T/CPF 0002.4-2018 储备物资的包装、标识、堆码和存储 第4部分：稀有难熔金属

本标准规定了稀有难熔金属储备物资的包装材料要求、包装材料检验方法、包装方式、标识、码垛和存储。用于锗锭、铟锭、钽锭、铌锭、锑锭等箱装物资的包装材料要求、包装材料检验方法、包装方式、标识、码垛和存储。 由于稀有难熔金属储备物资都是以密封塑料袋为内包装，以木箱为外包装物进行包装，因此把这几类易氧化的锭状储备物资放到此标准中来，其他箱装锭状物资可参照此标准执行。

Packaging, marking, stacking and storage of reserves - Part 4: Rare and refractory metals

T/CPF 0002.1-2018 储备物资的包装、标识、堆码和存储 第1部分：稀土氧化物及精矿类

本标准规定了稀土氧化物、钨精矿、焙烧钼精矿、金属钴的包装材料要求、包装材料检验方法、包装方式、标识、码垛和存储。用于稀土氧化物、钨精矿、焙烧钼精矿、金属钴等桶装物资的包装材料要求、包装材料检验方法、包装方式、标识、码垛和存储。 由于稀土氧化物、钨精矿、焙烧钼精矿、金属钴等储备物资都是以塑料袋做为内包装物，以钢桶作为外包装物，并采用托盘堆码的方式进行储存，因此把这几类储备物资放到此标准中来，其他桶装物资可参照执行。

Packaging, marking, stacking and storage of reserve materials Part 1: Rare earth oxides and concentrates

T/CPF 0002.3-2018 储备物资的包装、标识、堆码和存储 第3部分：贵金属

本标准规定了稀贵金属储备物资的包装材料要求、包装材料检验方法、包装方式、标识内容、码垛方式和存储要求。适用于铂锭等稀贵金属储备物资的包装、标识、码垛和存储。 由于铂锭等稀贵金属储备物资都是以塑料瓶或保险箱做为主要包装物，因此把这几类储备物资放到此标准中来，其他稀贵金属战略储备物资可参照执行。

Packaging, marking, stacking and storage of reserves - Part 3: Precious metals

T/CPF 0002.2-2018 储备物资的包装、标识、堆码和存储 第2部分：大宗有色金属

本标准规定了阴极铜、铝锭、锌锭、锡锭、钛铸锭、电解镍的包装材料要求、包装材料检验方法、包装方式、标识内容、堆码方式和存储要求。用于阴极铜、铝锭、锌锭、锡锭、钛铸锭、电解镍的包装、标识、堆码和存储。 由于阴极铜、铝锭、锌锭、锡锭、钛铸锭、电解镍均采用裸装打捆包装方式，其他裸装打捆物资的包装、标识、堆码和存储可参照此标准执行。

Packaging, labelling, stacking and storage of stockpiles - Part 2: Bulk non-ferrous metals

WB/T 1094-2018 铁矿石仓储服务规范

Iron ore warehousing service specifications

DB44/T 2075-2017 满箱检测机

本标准规定了满箱检测机的术语和定义；型号、型式、基本参数及工作条件；技术要求；试验方法；检验规则；标志、包装、运输与贮存。 本标准适用于在线满箱检测的机械，主要应用于食品、医药、日化等行业，食品、酒、饮料、医药、日化等产品装箱后，检测实际重量和设定重量相比较，以检查其包装箱内是否有产品缺漏，并将不合格的成品箱自动剔除。

Full box detector

VDI 2700 Blatt 10.1-2016 道路车辆负载的固定 预制混凝土构件的固定 平面混凝土构件

The standard applies to the transport of plane concrete elements with a loading width of up to 3,00 m. It describes a selection of appropriate procedures and methods for securing plane concrete elements on road vehicles for freight transportation, without claiming completeness. The standard is based on studies on the determination of coefficients of friction as well as the current state of load securing recommendations for ceiling and wall panels made of concrete. The standard is intended for the use of consignors, carriers, shippers, vehicle operators (drivers), vehicle owners and such persons as the law, ordinances, contracts or other codes of practice make responsible for securing the load and for safe transportation.

Securing of loads on road vehicles - Securing of precast concrete elements - Plane concrete elements

ASTM D6253-16 木材包装材料的处理和/或标记的标准实施规程

4.1 This practice establishes the criteria to treat, or mark, or both WPM with permanent identification for the phytosanitary treatment, or intended service cycle, or both, repair, specification used, and other designated characteristics. 4.2 The marking of the WPM shall be performed after ensuring the material complies with the applicable specification. 1.1 This practice covers the development of recommended treatment, or marking practices, or both, for wood packaging materials (WPM) and aids in identifying WPM as to phytosanitary treatment, intended service cycles, repair, the specific specification used to manufacture or recycle, and other user designated characteristics. 1.2 This practice identifies WPM treated, or marked, or both in accordance with industry, government, or international recognized standards. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Treatment and/or Marking of Wood Packaging Materials

IWA 16-2015 国际协调一致的量化二氧化碳排放量的货运方法

International harmonized method(s) for a coherent quantification of CO2e emissions of freight transport

VDI 2700 Blatt 2-2014 固定道路车辆上的负载 束缚力的计算 基础知识

The standard demonstrates in principle the forces to be encountered under specific operating conditions. It also discusses the forces acting on the lashing devices in order to achieve effective load restraint. The lashing methods discussed in this standard cover most of the possible load restraint cases for mixed loads. The standard applies for transport of mixed loads on trucks and trailers.

Securing of loads on road vehicles - Calculation of tie-down forces - Fundamentals

DIN EN 12195-1 Berichtigung 1:2014 道路车辆的荷载限制. 安全性. 第1部分: 牢固作用力的计算; 德文版本EN 12195-1-2010, DIN EN 12195-1-2011-06技术勘误; 德文版本EN 12195-1-2010/AC-2014

Load restraining on road vehicles - Safety - Part 1: Calculation of securing forces; German version EN 12195-1:2010, Corrigendum to DIN EN 12195-1:2011-06; German version EN 12195-1:2010/AC:2014

EN 12195-1:2010/AC:2014 道路车辆负载限制.安全.第1部分:计算获得力量 包含修改件AC,2014

Load restraining on road vehicles - Safety - Part 1: Calculation of securing forces

ASTM F2325-14 运输设施用多层钢 (MLS) 和其他金属层状垫片的标准分类

4.1 This classification is intended to encourage uniformity in reporting properties of MLS and Metal Layer gaskets, to provide a common language for communications between producers and users, and to guide engineers and designers in the application and construction of commercially available gaskets. (A) This classification may also be used to classify Single Layer Steel (SLS) Gaskets.(B) Refer to Specification A666 or Specification A109/A109M for Stainless Steel and Low Carbon Steel, respectively. Other metals not referenced in the table or not covered by Specification A666 or Specification A109/A109M must be defined by the producer/user (that is, H – High Temperature Alloy).(C) Refer to Practice D1418 for general information regarding rubber coating types and use Classification D2000 to define the physical properties of the rubber. This physical property information is typically specified on the gasket drawing or the customer specification, or both.(D) Coated side as specified on part drawing. 4.2 Suffix Table 2 is provided to allow hardness designation for Active, Inactive, or Load Stoppers. 4.2.1 If suffixes are not to be used, only the basic callout from Table 1 is required. If a suffix is used for 1 layer, it must be specified for all layers, even if a “0” is used. It cannot be assumed that hardnesses of like layers are the same; if used, all layers must be specified separately. The first layer specified must be indicated on the part drawing. To use a hardness call-out, at the end of the base callout leave a space followed by the “HR” suffix with a series of suffix numbers to specify the hardnesses for each layer. 4.2.1.1 Example: ASTM F2325, A32ANBW11 HR252—Example from Table 1 modified to add hardness requirement for the three metal layers. Active layers 1 and 3 are designated to be the same, 1/4 hard steel. Stopper layer 2 is designated to be full hard steel. 1.1 This classification covers a means for specifying Multi-Layer Steel (MLS) and other Metal Layer Gaskets for Transportation Applications by application and construction. These structures are composed of one or more steel or metal layers of material, which may have coatings or embossments. Commercial materials designated as composite or enveloped gaskets are excluded from this classification and are covered by Classification F868 and Practice

Standard Classification for Multi-Layer Steel (MLS) and Other Metal Layer Gaskets for Transportation Applications

KS T ISO 21898:2013 包装.非危险货物用软过渡性散货集装箱

이 표준은 가루, 과립 또는 반죽 형태의 비위험물을 담고, 일체형 또는 분리형 장치에 의해서 들어올려질 수 있는 연성형 중형 산적용기를 위한 재질, 구조와 설계의 요건, 시험의 종류, 성적서 그리고표시 사항의 요건을 명시하고 있다.또한 연성형 중형 산적용기의 선택과 안전한 사용법에 대해서도 정보를 제공한다.

Specification for flexible intermediate bulk containers(FIBCs) for non-dangerous goods