55.180.99 有关货物调运的其他标准 标准查询与下载

DIN 75410-3:2004 道路车辆上货物的固定.第3部分:旅行货车中货物的固定

Securing of cargo on road vehicles - Part 3: Securing of cargo in truck station wagons (closed body)

ISO 21898:2004 包装.非危险货物用软的过渡性散货集装箱

This International Standard specifies materials, construction and design requirements, type test, certification and marking requirements for flexible intermediate bulk containers (FIBCs) intended to contain non-dangerous solid materials in powder, granular or paste form, and designed to be lifted from above by integral or detachable devices. Guidance is also provided on the selection and safe usage of FIBCs.

Packaging - Flexible intermediate bulk containers (FIBCs) for non-dangerous goods

CNS 13190-2004 包装货物与单位装载试验之前处理

本标准适用于完整之运输包装货物及单位装载货物等各项试验前，应施加之处理

Packaging－Complete, filled transport packages and unit loads－Conditioning for testing

DS/CEN/TS 13853:2004 组合运输用交换体 C 745-S16 型可堆叠交换体 尺寸、设计要求和测试

This Technical Specification specifies dimensions, design requirements and testing requirements of stackable swap bodies type C 745-S16 which are suitable for domestic and international multimodal conveyance by road, rail, short sea and coastal sea transport (including Ro/Ro or ferry transport) and inland waterways.

Swap bodies for combined transport - Stackable swap bodies type C 745-S16 - Dimensions, design requirements and testing

VDI 4429-2003 柔性中型散装容器（FIBCs）的应用

The document gives a general introduction to, and guidance on the practical application of, flexible intermediate bulk containers. Particular attention is directed to the filling and discharging, and to transport, transhipment, and storage processes.

Application of Flexible Intermediate Bulk Containers (FIBCs)

ISO 16467:2003 包装.危险品用运输包装件.IBCs用试验方法

This European Standard specifies the design type test requirements for Intermediate Bulk Containers (IBCs) as described in 3.2 of this standard and intended for use in the transport of dangerous goods.

Packaging - Transport packages for dangerous goods - Test methods for IBCs

CNS 13251-2003 运输包装货物矩形尺度

本标准适用于单位装载化体系，促进物流合理化为目的，以标准平面尺度(模块)600 mm × 400 mm及550 mm × 366 mm为基础之－系列运输包装货物之矩形尺度

Dimensions of rigid rectangular packages – Transport packages

ASTM F2325-03(2009) 运输设施用多层钢(MLS)和其他金属层状垫片的标准分类

This classification is intended to encourage uniformity in reporting properties of MLS and Metal Layer gaskets, to provide a common language for communications between producers and users, and to guide engineers and designers in the application and construction of commercially available gaskets.1.1 This classification covers a means for specifying Multi-Layer Steel (MLS) and other Metal Layer Gaskets for Transportation Applications by application and construction. These structures are composed of one or more steel or metal layers of material, which may have coatings or embossments. Commercial materials designated as composite or enveloped gaskets are excluded from this classification and are covered by Classification F868 and Practice F336, respectively. 1.2 Since all of the properties that contribute to gasket performance are not included, use of this classification as a basis for selecting an MLS or Metal Layer gasket is limited. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Classification for Multi-Layer Steel (MLS) and Other Metal Layer Gaskets for Transportation Applications

ASTM D6911-03(2010) 实验室分析用环境样品的包装和装运的标准指南

This standard provides guidance in determining the most appropriate procedures for packaging and shipping environmental samples. Use of this guide by personnel involved in packaging and shipping environmental samples will facilitate safe, effective and compliant procedures.1.1 This standard provides guidance on the selection of procedures for proper packaging and shipment of environmental samples to the laboratory for analysis to ensure compliance with appropriate regulatory programs and protection of sample integrity during shipment. 1.2 This standard does not address transport of hazardous wastes for disposal purposes. 1.3 This standard does not address the selection of parameter-specific sample bottles or containers. 1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of the many unique aspects of a project. The word “standard” in the title of this guide means only that the guide has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Packaging and Shipping Environmental Samples for Laboratory Analysis

VDI 2700 Blatt 2-2002 固定道路车辆上的负载 束缚力

Hints and recommendations for the restraining of the commonly transported goods are provided in guideline VDI 2700. The document demonstrates in principle the forces to be encountered under specific operating conditions. It also discusses the forces acting on the lashing devices in order to achieve effective load restraint. The lashing methods discussed in this guideline cover most of the possible load restraint cases for mixed loads. Applies for transport of mixed loads on trucks and trailers.

Securing loads on road vehicles - Tie down forces

LST EN 13054-2002 包装 完整的、装满的运输包装 确定包装重心的试验方法

Packaging - Complete, filled transport packages - Test methods for the determination of the centre of gravity of a package

DIN 30823:2001 中等容量容器.硬质IBC.金属、硬质、塑料和复合中等容量容器.尺寸、设计和要求、标记

The document specifies rigid IBC up to 3000 l for the transport of liquid and solid products. It specifies dimensions, design requirements and marking.#,,#

Intermediate bulk containers - Rigid IBC - Metal, rigid plastics and composite intermediate bulk containers; Dimensions, design requirements, marking

BS EN 13054:2001 包装.完全填充运输包装.包裹重心测定方法

This standard specifies two methods of determining the location of the centre of gravity of flat sided rigid packages. In the following text, a package is called "a test item".

Packaging - Complete, filled transport packages - Test methods for the determination of the centre of gravity of a package

BS EN 12640:2001 货物和道路车辆的安全.货物运输用商业车辆的挂车点.最低要求和试验

This standard specifies the minimum requirements and test methods for lashing points fitted to commercial vehicles and trailers with flatbed body construction of maximum total mass above 3,5t and intended for general use. The standard does not apply to: - vehicles designed and constructed exclusively for the transportation of bulk materials; - vehicles designed and constructed exclusively for the transportation of specific cargo with particular securing requirements.

Securing of cargo on road vehicles - Lashing points on commercial vehicles for goods transportation - Minimum requirements and testing

BS EN 12195-2:2001 道路车辆的负载限动组件.安全性.人造纤维网绳

This Part of EN 12195 — specifies safety requirements for web lashing made from man-made fibres with flat woven webbings for multiple use and of lashing combinations with woven webbings for the safe surface transport of goods on road vehicles, e.g. trucks and trailers which are used on roads or located on vessels or on rail waggons and/or combinations thereof; — includes only tensioning devices to be hand driven with a maximum hand force of 500 N; — specifies methods for testing of web lashing for securing of loads; — deals with the significant hazards which could occur when web lashings are in use as intended and under conditions foreseen by the manufacturer (see clause 4 and Annex A); — includes composite load restraint assemblies also for the same purpose as above.

Load restraint assemblies on road vehicles - Safety - Web lashing made from man-made fibres

DIN EN 12640:2001 道路车辆货物安全性.商用货车系绑点.最低要求和试验

Securing of cargo on road vehicles - Lashing points on commercial vehicles for goods transportation - Minimum requirements and testing; German version EN 12640:2000

NF H90-210:2000 道路车辆上货物的固定.货物运输用商业车辆的捆绑点.最低要求和试验

Securing of cargo on road vehicles - Lashing points on commercial vehicles for goods transportation - Minimum requirements and testing.

VDI 2700 Blatt 7-2000 车辆上的负载安全 联合货运中负载的安全

The guideline deals with the securing of loads on road vehicles. It describes the special features in combined rail/road transport.

Safety of loads on vehicles - Safety of loads in combined freight transport

VDI 2700 Blatt 4-2000 固定道路车辆上的负载 货物重量分布

"The document describes a cargo weight distribution for loading trucks and trailers (articulated draw-bar trailers and rigid draw-bar trailers), semitrailer motor vehicles (semitrailer) as well as special vehicles. The maximum permissible axle loads and to avoid reducing the steering axle load below the minimum required for safe steering, so as to avoid compromising traffic safety."

Securing of loads on road vehicles - Cargo weight distribution

DS/EN 12406:1999 交换体 C 级热交换体 尺寸和一般要求

This European standard specifies the dimensions and basic requirements for thermal swap bodies of class C. These swap bodies are suitable for international exchange and for conveyance by road and rail including interchange between these forms of transport.

Swap bodies - Thermal swap bodies of Class C - Dimensions and general requirements