59.080.40 涂覆织物 标准查询与下载

QB/T 4913-2016 运动鞋用聚氨酯合成革安全要求

本标准规定了运动鞋用聚氨酯合成革的安全等级、要求、试验方法、取样和判定规则。 本标准适用于以布基、聚氨酯树脂等为主要原料，经湿、干法加工制成的运动鞋用聚氨酯合成革。

Safety requirements of polyurethane synthetic leather for sports shoes

QB/T 4911-2016 服装用水性聚氨酯合成革技术条件

本标准规定了服装用水性聚氨酯合成革的分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于以水性聚氨酯树脂为主要原料，以针织布、机织布或非织造布为底基，经涂覆或机械发泡及后整理等工艺制成的服装用合成革。

Technical requirements for waterborne polyurethane synthetic leather for garment

NF G37-114*NF ISO 7229:2015 橡胶或塑料涂覆织物.透气性测量

Rubber - or plastics-coated fabrics - Measurement of gas permeability

T/ZZB 022-2015 防护鞋底用聚氨酯树脂

本标准规定了防护鞋底用聚氨酯树脂产品的要求、检验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本标准适用于由多元醇混合物为主要成分的A组分，异氰酸酯预聚体为主要成分的B组分组成的双组分防护鞋底用聚氨酯树脂，行业内又称防护鞋鞋底原液。本标准也适用于安全鞋底用聚氨酯树脂。

Polyurethane resin for sole of protective footwear

GSO ISO 2231:2015 橡胶或塑料涂层织物 调节和测试的标准大气

This International Standard specifies the requirements for conditioning and methods of conditioning employed for rubber- or plastics-coated fabrics.

Rubber- or plastics-coated fabrics -- Standard atmospheres for conditioning and testing

GSO ISO 4637:2015 橡胶涂层织物 橡胶与织物粘合力的测定 直接拉伸法

This International Standard specifies a method for the determination of rubber-to-fabric adhesion under direct tension. It is only suitable when the material to be tested is substantially uniform in thickness and flat or sufficiently flexible to be maintained flat under light pressure. It is particularly suitable for materials having a very thin rubber layer which are difficult to test by stripping or peeling methods. However it should be noted that the results obtained by this method will not necessarily correlate with those obtained by a stripping test such as that described in ISO/R 36, Determination of the adhesion strength of vulcanized rubbers to textile fabrics.

Rubber-coated fabrics -- Determination of rubber-to-fabric adhesion -- Direct tension method

GSO ISO 8096:2015 防水服装用橡胶或塑料涂层织物 规范

This International Standard specifies the requirements for water vapour permeable and non water vapour permeable coated fabrics suitable for use in the construction of water penetration resistant clothing. This standard does not address the method of fabrication of the garment. However, the physical requirements attributed to water penetration resistance of the final garment should in no way be inferior to those listed for the coated fabric. NOTE The coding system applicable to the coating polymer(s) employed in the manufacture of these coated fabrics is given in Table 1.

Rubber- or plastics-coated fabrics for water-resistant clothing -- Specification

GSO ISO 5981:2015 橡胶或塑料涂层纺织品 弯曲剪切和摩擦强度的测定

This International Standard specifies two methods of evaluating the resistance to combined shear flexing and rubbing of rubber- or plastics-coated fabrics. Rubbing is either forced by application of a pressure foot (method A), or is caused by simple contact between the faces of the test pieces (method B). Method B (without application of the pressure foot) is preferred in all cases where the foot would damage the test piece through an abrasive effect where this is not required, e.g. materials with sticky surfaces, light coatings such as polyurethanes on rough surfaces. The test may be carried out on products as delivered or after pre-treatments such as wetting or accelerated ageing. NOTE The results obtained using method A and method B cannot be compared as there is no correlation between the two methods.

Rubber- or plastics-coated fabrics -- Determination of resistance to combined shear flexing and rubbing

GSO ISO 2411:2015 橡胶或塑料涂层纤维涂层附着力的测定

This European Standard specifies a method of determining the coating adhesion strength of coated fabrics.

Rubber- or plastics-coated fabrics -- Determination of coating adhesion

GSO ISO 2286-3:2015 涂有橡胶或塑料层的纺织品 卷筒性能的测定 第3部分：厚度测定方法

This part of ISO 2286 describes a method for the determination, at a specified pressure, of the thickness of rubber and plastics-coated fabrics, irrespective of the type of substrate employed. It is applicable to single-face, double-face and double-texture coated fabrics, as well as materials in which an expanded layer is included in the coating.

Rubber- or plastics-coated fabrics -- Determination of roll characteristics -- Part 3: Method for determination of thickness

GSO ISO 4646:2015 涂有橡胶或塑料的纺织品 低温冲击试验

1.1 This International Standard specifies a procedure for determining the lowest temperature at which fabrics coated with rubber or plastics will not exhibit fractures or coating cracks when subjected to specific impact conditions. 1.2 Fabrics coated with rubber or plastics are used in many applications involving low-temperature flexing with or without impact. Data obtained by this method may be used to predict the behaviour of these coated fabrics at low temperatures only in the applications in which the conditions of deformation are similar to those specified in the method.

Rubber- or plastics-coated fabrics -- Low-temperature impact test

GSO ISO 1420:2015 橡胶或塑料涂层织物抗水渗透性的测定

This International Standard specifies a pass/fail method for the determination of the resistance of rubber- or plastics-coated fabrics to water penetration (hydrostatic resistance) when subjected to a specific hydrostatic pressure over a fixed period of time. Two test specimen shapes are given: one is circular, the other square.

Rubber- or plastics-coated fabrics -- Determination of resistance to penetration by water

GSO ISO 4675:2015 涂有橡胶或塑料的纺织品 低温弯曲试验

This international Standard specifies a method for determining the ability of fabrics coated with rubber or plastics to resist the effect of low temperature when subjected to bending at specified temperatures after definite periods of exposure. It is applicable to material with a thickness within the range 0,1 mm to 2,2 mm. For materials of greater thickness than this, modifications to the standard equipment are necessary (see 8.2, third paragraph). Because fabrics coated with rubber or plastics are used in different applications requiring lowtemperature flexing, no general relationship between this test and service performance can be given or implied.

Rubber- or plastics-coated fabrics -- Low-temperature bend test

GSO ISO 2286-2:2015 橡胶或塑料涂层织物 卷筒性能的测定 第2部分：单位面积总质量、涂层单位面积质量和基材单位面积质量的估算方法

This part of ISO 2286 describes methods of determining the total mass per unit area, the mass per unit area of the coating and the mass per unit area of the substrate cloth of a rubber- or plastics-coated fabric. Methods for removing coatings of specific compositions are described in annex A.

Rubber- or plastics-coated fabrics -- Determination of roll characteristics -- Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate

GSO ISO 6179:2015 硫化或热塑性橡胶 橡胶板和橡胶涂层织物 挥发性液体透过率的测定（重量法）

This International Standard specifies two methods for determining, by measurement of the transmission rate, the permeability of rubber to volatile liquids diffusing into open air. It is applicable only to materials in sheet form and to coated fabrics having thicknesses between 0,2 mm and 3,0 mm. It is restricted to transmission rates of more than 0,1 g/m2·h. The methods are particularly useful for comparing the relative transmission rates of one liquid through different materials, or of several liquids through one material. Method A, with refilling, is used when testing mixtures of liquids which give different transmission rates. Method B, with no refilling, is used for a single-component liquid. NOTE A method for the determination of water vapour transmission rate is given in ISO 2528, Sheet materials — Determination of water vapour transmission rate — Gravimetric (dish) method.

Rubber, vulcanized or thermoplastic -- Rubber sheets and rubber-coated fabrics -- Determination of transmission rate of volatile liquids (gravimetric technique)

GSO ISO 1419:2015 橡胶或纤维涂层塑料 加速老化测试

This International Standard describes four methods of assessing the resistance of coated fabrics to deterioration by accelerated ageing.

Rubber- or plastics-coated fabrics -- Accelerated-ageing tests

GSO ISO 36:2015 硫化橡胶或热塑性橡胶 对纺织物粘合力的测定

This International Standard specifies a method of test for measuring the force required to separate, by stripping, two plies of fabric bonded with rubber, or a rubber layer and a fabric ply bonded together. The method is applicable when the ply surfaces are approximately plane or when they are in the form of a cylinder having an internal diameter greater than approximately 50 mm. The method is not applicable when the ply surfaces contain sharp bends, angles or other gross irregularities which cannot be excluded when cutting out test pieces. This International Standard does not apply to coated fabrics, which are tested in accordance with ISO 2411, Rubber- or plastics-coated fabrics — Determination of coating adhesion, or textile conveyor belts, which are tested in accordance with ISO 252, Conveyor belts — Adhesion between constitutive elements — Test methods.

Rubber, vulcanized or thermoplastic -- Determination of adhesion to textile fabrics

GSO ISO 6450:2015 涂有橡胶或塑料涂层的纺织品 耐液体性的测定

This International Standard specifies two methods (methods 1 and 2) of evaluating the resistance of fabrics coated with plastics or with vulcanized rubber to the action of liquids by measurement of selected properties of the materials before and after immersion in selected liquids. The difference between the two methods is as follows: — In method 1, excess liquid is removed from the test pieces, after immersion, by wiping. — In method 2, the test pieces are immersed in a volatile liquid and excess liquid is subsequently removed by drying in an oven.

Rubber- or plastics-coated fabrics -- Determination of resistance to liquids

GSO ISO 5978:2015 橡胶或塑料涂层纤维 分离阻力的测定

This International Standard specifies a method for the determination of the resistance of rubber- or plastics-coated fabrics to blocking. The method specified is acceptable in most cases. If it is desired to use conditions other than those specified, these may be mutually agreed between the contracting parties but such variations shall be stated in the test report.

Rubber- or plastics-coated fabrics -- Determination of blocking resistance

GSO ISO 5470-2:2015 覆盖橡胶或塑料层的纺织品耐磨性的测定 第2部分：马丁代尔磨料

This part of ISO 5470 details two separate methods for determining the resistance of a material to wet and dry abrasion. It is applicable to the coated surface or surfaces of coated fabrics. If the abrasion behaviour of the uncoated surface of a coated fabric is to be determined, use the methods for uncoated textiles described in the various parts of ISO 12947.

Rubber- or plastics-coated fabrics -- Determination of abrasion resistance -- Part 2: Martindale abrader