59.080.40 涂覆织物 标准查询与下载

KS M ISO 3011-2022 橡胶或塑料涂层织物静态条件下耐臭氧开裂性的测定

Rubber or plastics coated fabrics Determination of resistance to ozone cracking under static conditions

KS M ISO 5470-2-2022 橡胶或塑料涂层织物耐磨性的测定第2部分:马丁代尔磨光机

Rubber or plastics coated fabrics Determination of abrasion resistance Part 2: Martindale abrader

KS K 0766-2022 涂层布低温效应的试验方法

Test method for low temperature effect on coated cloth

KS K 1400-2022 防水织物片

Water proof textile sheets

T/CSTM 00523-2022 环保型水产养殖储水耐水压复合纺织品

本文件规定了环保型水产养殖储水耐水压复合纺织品的技术要求、试验方法、检验规则、包装、标志、储存、运输等。 本文件适用于水深3米以内的养殖池防渗用、以PVC、TPU等与织物复合的耐水压复合纺织品。

Environmental-friendly water-resistant composite textiles for aquaculture water storage

T/CASME 87-2022 鞋用高物水性聚氨酯合成革技术规范

本文件规定了鞋用高物水性聚氨酯合成革的产品分类、要求、检验方法、检验规则、标志、包装、运输和贮存技术要求。

Technical specification for high waterborne polyurethane synthetic leather for shoes

ASTM D4005-92(2022) PVC分散涂层的塑料涂层织物熔合完整性的标准试验方法

1.1 This test method describes a simple procedure to determine the completeness of fusion of poly(vinyl chloride) (PVC) dispersion coatings on fabric. This test applies primarily to coatings with a mechanical bond and does not include tie coating. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Plastic-Coated Fabrics—Completeness of Fusion of PVC Dispersion Coatings

ASTM D3393-91(2022) 涂层织物防水性标准规范

1.1 This specification sets forth the minimum requirements for hydrostatic resistance of fabrics coated with rubber or plastics. Coated fabrics satisfying these requirements are considered to be waterproof. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Coated Fabrics—Waterproofness

ASTM D5193/D5193M-93(2022) 涂层织物空气保持力的标准试验方法

1.1 This test method describes the determination of the retention of air by fabrics coated on one or both sides with rubber. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Coated Fabrics—Air Retention

HG/T 3052-2022 橡胶或塑料涂覆织物 涂覆层粘合强度的测定

Determination of adhesive strength of coatings on rubber or plastic coated fabrics

HG/T 2580-2022 橡胶或塑料涂覆织物 拉伸强度和拉断伸长率的测定

Determination of tensile strength and elongation at break of rubber or plastic coated fabrics

QB/T 5754-2022 水性/无溶剂聚氨酯复合人造革

Water-based/solvent-free polyurethane composite artificial leather

T/CFIA P4-2022 高硅氧改性玻璃纤维覆膜滤料

本文件规定了高硅氧改性玻璃纤维覆膜滤料的材料要求、单位面积质量、厚度、宽度、理化指标、过滤性能、外观要求等。同时给出了相关指标的测试方法和试验示意图。

High silica modified glass fiber membrane filter material

HG/T 2581.1-2022 橡胶或塑料涂覆织物 耐撕裂性能的测定 第1部分：恒速撕裂法

Determination of the tear resistance of rubber or plastic coated fabrics Part 1: Constant rate tear method

HG/T 2582-2022 橡胶或塑料涂覆织物 耐水渗透性能的测定

Determination of the resistance of rubber or plastic coated fabrics to water penetration

QB/T 5677-2022 聚氨酯超细纤维合成革单位产品能耗限额

Energy consumption quota per unit product of polyurethane microfiber synthetic leather

BS ISO 7229:2022 橡胶或塑料 涂层织物 透气性测量

1   Scope This document specifies two methods for measuring gas transmission through rubber- or plastics-coated fabrics, a property known as permeability.

Rubber or plastics. coated fabrics. Measurement of gas permeability

BS ISO 4646:2022 橡胶或塑料涂层织物 低温冲击试验

Rubber- or plastics-coated fabrics. Low-temperature impact test

ISO 7229:2022 橡胶或塑料涂层织物.透气性测量

This document specifies two methods for measuring gas transmission through rubber- or plastics- coated fabrics, a property known as permeability.

Rubber- or plastics-coated fabrics — Measurement of gas permeability

ISO 4646:2022 橡胶或塑料涂层织物.低温冲击试验

This document specifies a procedure for determining the lowest temperature at which rubber- or plastics-coated fabrics will not exhibit fractures or coating cracks when subjected to specific impact conditions. Rubber-or plastics-coated fabrics are used in many applications involving low-temperature flexing with or without impact. Data obtained by this method can be used to predict the behaviour of these coated fabrics at low temperatures only in the applications in which the conditions of deformation are similar to those specified in the method.

Rubber- or plastics-coated fabrics — Low-temperature impact test