59.100.20 碳纤维材料 标准查询与下载

ISO 11567:2018 碳纤维 长丝直径和横截面积的测定

This document specifies five test methods used for the determination of the diameter and crosssectional area of single carbon fibre filaments. The shape of the cross-section of the filaments from different suppliers can vary significantly. The term “diameter” used in this document applies to all cases, from a “true” diameter, where the filament is exactly circular in cross-section, to an “apparent” diameter where the filament is not circular. The methods proposed are not necessarily directly applicable to all types of filament. The product specification determines the method to be used. If there is no specification, the selection of the appropriate method is a matter of judgement. The details given here are considered to be sufficiently precise to enable this choice to be made.

Carbon fibre - Determination of filament diameter and cross-sectional area

BS ISO 30012:2016+A1:2018 碳纤维增强塑料 破碎物体尺寸和长宽比的测定

1   Scope This International Standard specifies test methods for measurement of the size and aspect ratio of crushed carbon-fibre-reinforced plastics (CFRP), especially for recycling purpose. In this International Standard the shape of crushed CFRP, the fragment, is treated as a rectangular shape, and the measurement of the long and short sides of the shape is described. It applies to fragments of the following average dimensions: — length of the long side: 5 mm to 50 mm; — width of the short side: 1 mm to 10 mm. This International Standard provides three measuring methods, two methods are manual methods using microscope and scale and the third method is an automatic method using a measuring apparatus. Crushed CFRP obtained from thermosetting or thermoplastic resin matrices are covered by this International Standard. NOTE If the crushed CFRP contain a lot of small fragments and fine particle, it is intended to screen out by a sieve of 1 mm size before the measurement.

Carbon-fibre-reinforced plastics. Determination of the size and aspect ratio of crushed objects

ISO 30012:2016/Amd 1:2018 碳纤维增强塑料. 压碎物尺寸和形状比的测定.修改件1

Carbon-fibre-reinforced plastics - Determination of the size and aspect ratio of crushed objects; Amendment 1

GOST R 58062-2018 碳纤维织物. 技术要求和试验方法

Fabrics based on carbon fibers. Technical requirements and test methods

KS L 6801-2017 碳纤维密度的测定

Carbon fiber－Determination of density

YB/T 5290-2017 高炉炭块铁水渗透性试验方法

Test method for molten iron permeability of blast furnace carbon blocks

YB/T 4037-2017 高炉用半石墨质炭块

Semi-graphite carbon block for blast furnace

YB/T 122-2017 高炉用石墨块

Graphite block for blast furnace

YB/T 910-2017 自焙炭块焙烧线收缩(或线膨胀)率测定方法

Method for determination of linear shrinkage (or linear expansion) rate of roasting of self-baked carbon blocks

YB/T 4625-2017 高炉水冷管用石墨瓦

Graphite tiles for blast furnace water-cooled tubes

YB/T 4585-2017 铸锭炉用板状结构炭/炭复合材料

Plate structural carbon/carbon composite materials for ingot furnaces

YB/T 4589-2017 单晶炉保温用炭/炭复合材料

Carbon/carbon composite materials for single crystal furnace insulation

YB/T 4588-2017 单晶炉用板状结构炭/炭复合材料

Plate structure carbon/carbon composite materials for single crystal furnaces

YB/T 4586-2017 铸锭炉保温用炭/炭复合材料

Carbon/carbon composite materials for ingot furnace insulation

YB/T 4587-2017 单晶炉用炭/炭复合材料发热体

Carbon/carbon composite heating element for single crystal furnace

ASTM D4018-17 连续丝碳纤维和石墨纤维拖链性能的标准测试方法

1.1 These test methods cover the preparation and tensile testing of resin-impregnated and consolidated test specimens made from continuous filament carbon and graphite yarns, rovings, and tows to determine their tensile properties. 1.2 These test methods also cover the determination of the density and mass per unit length of the yarn, roving, or tow to provide supplementary data for tensile property calculation. 1.3 These test methods include a procedure for sizing removal to provide the preferred desized fiber samples for density measurement. This procedure may also be used to determine the weight percent sizing. 1.4 These test methods include a procedure for determining the weight percent moisture adsorption of carbon or graphite fiber. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows

ASTM D7775-16 小型石墨样品测量标准指南

1.1 This guide covers best practice for properties measurements on small (nonstandard) graphite specimens and requirements for representing properties of the bulk material. This guide is aimed specifically at measurements required on nuclear graphites, where there may be constraints on the geometry or volume of the test specimen, or both. The objective of this guide is to provide advice on how the application of selected standards under noncompliant conditions can be tested for suitability. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Measurements on Small Graphite Specimens

BS ISO 30012:2016 碳纤维增强塑料. 粉碎物体尺寸和纵横比的测定

Carbon-fibre-reinforced plastics. Determination of the size and aspect ratio of crushed objects

ISO 30012:2016 碳纤维增强塑料. 压碎物尺寸和形状比的测定

This International Standard specifies test methods for measurement of the size and aspect ratio of crushed carbon-fibre-reinforced plastics (CFRP), especially for recycling purpose. In this International Standard the shape of crushed CFRP, the fragment, is treated as a rectangular shape, and the measurement of the long and short sides of the shape is described. It applies to fragments of the following average dimensions: — length of the long side: 5 mm to 50 mm; — width of the short side: 1 mm to 10 mm. This International Standard provides three measuring methods, two methods are manual methods using microscope and scale and the third method is an automatic method using a measuring apparatus. Crushed CFRP obtained from thermosetting or thermoplastic resin matrices are covered by this International Standard. NOTE If the crushed CFRP contain a lot of small fragments and fine particle, it is intended to screen out by a sieve of 1 mm size before the measurement.

Carbon-fibre-reinforced plastics - Determination of the size and aspect ratio of crushed objects

YB/T 5192-2016 高炉炭块尺寸

本标准规定了高炉炭块尺寸。 本标准适用于砌筑大中型高炉炉底、炉缸用炭块。

Dimensions for the carbon block of blast furnaces