59.120.30 织机、织造机器 标准查询与下载
共找到 423 条与 织机、织造机器 相关的标准，共 29 页
本标准规定了织机用铝合金综框(以下简称“综框”)的基本要求、分类和标记、技术要求、试验方法、检验规则、包装、标志、运输和贮存、质量承诺与服务。 本标准适用于穿综杆用托座固定于综框横梁（Z型）或穿综杆直接固定于综框横梁（M型）的综框。
Aluminium-alloy heald frames for weaving machines
- ICS
- 59.120.30
- CCS
- C355
- 发布
- 2018-07-13
- 实施
- 2019-02-28
本标准规定了电子提花机型式与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于与各类织机配套织制各种提花织物的电子提花机。
Electronic jacquard machines
- ICS
- 59.120.30
- CCS
- C3990
- 发布
- 2018-05-31
- 实施
- 2019-02-28
This document specifies a hydrostatic pressure method for determining the resistance of fabrics to penetration by water. The method is applicable to all types of fabrics which are intended to be water resistant whether or not they have been given a water-resistant or water-repellent finish.
Textile machinery — Weaving machine temples — Part 2: Full-width temples
- ICS
- 59.120.30
- CCS
- 发布
- 2018-03-27
- 实施
- 0000-00-00
Digital Control System of Air-jet Loom
- ICS
- 59.120.30
- CCS
- W92
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本标准规定了氨纶整经机的术语和定义、型式与基本参数、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于经编整经用的氨纶整经机。
Spandex warper
- ICS
- 59.120.30
- CCS
- W94
- 发布
- 2016-10-22
- 实施
- 2017-04-01
本标准规定了纺纱准备和纺纱机械上罗拉包覆物用胶管的分类和标记、要求、试验方法、检验规则、包装、标志、运输和储存。 本标准适用于纺纱准备和纺纱机械用邵尔A硬度为60～90度的上罗拉包覆物用胶管（以下简称“胶管”）。
Spinning preparatory and spinning machinery.Rubber tubes of the coverings for the top rollers
- ICS
- 59.120.30
- CCS
- W94
- 发布
- 2016-10-22
- 实施
- 2017-04-01
本标准规定了“浙江制造”喷气织机用钢筘(以下简称喷气筘)的范围、规范性引用文件、术语和定义、基本要求、分类和标识、技术要求、试验方法、检验规则、包装、标志、贮存、质量承诺。 本标准适用于喷气织机用钢筘的生产、检验、销售及当产品发生质量纠纷时测试判定依据。
Reeds for air jet weaving machines
- ICS
- 59.120.30
- CCS
- C3551
- 发布
- 2016-09-30
- 实施
- 2017-05-17
Textile machinery - Safety requirements - Part 5: Preparatory machinery to weaving and knitting - Amendment 2 (ISO 11111-5:2005/Amd 2:2016)
- ICS
- 59.120.30
- CCS
- 发布
- 2016-06-15
- 实施
- 2016-09-30
Scope is not provided for this standard
Textile machinery and accessories -- Bars for drop wires for electrical warp stop motions
- ICS
- 59.120.30
- CCS
- 发布
- 2015-12-21
- 实施
This part of ISO 366 specifies the dimensions and designation of metal reeds with plate baulk for weaving machines.
Textile machinery and accessories -- Reeds -- Part 2: Dimensions and designation of metal reeds with plate baulk
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies the dimensions of paper patterns for dobbies for use in the textile industry.
Textile machinery and accessories -- Paper patterns for dobbies -- Dimensions
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 366 specifies the dimensions of pitch bound reeds for use in the textile machinery industry.
Textile machinery and accessories -- Reeds -- Part 1: Pitch bound reeds -- Dimensions
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies the principal dimensions, tolerances and designation of drop wires for mechanical, electromechanical and electrical warp stop motions for weaving machines. This International Standard applies only to drop wires suited for Uster and Reed Chatwood automatic drawing-in systems. These drop wires are always closed with U-shaped thread eye and are distinguished as follows: a) for mechanical and electromechanical warp stop motions — M1 (for the Uster drawing-in system) — M2 (for the Reed Chatwood drawing-in system) — M3 (for the Uster and Reed Chatwood drawing-in systems) b) for electrical warp stop motions — E1 (for the Uster drawing-in system) — E2 (for the Reed Chatwood drawing-in system) — E3 (for the Uster and Reed Chatwood drawing-in systems)
Textile machinery and accessories -- Drop wires for warp stop motions for weaving machines with automatic drawing-in
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard gives the designations of dimensions of serrated bars for mechanical warp stop motions. Values of the dimensions of the cross-section of assembled serrated bars are also given. NOTE— In addition to the designations given in the three official ISO languages (English, French and Russian), this International Standard gives, in an annex, the equivalent designations in German; these have been included at the request of ISO Technical Committee TC 72 and are published under the responsibility of the member body for Germany (DIN). However, only the designations given in the three official languages can be considered as ISO designations.
Textile machinery and accessories -- Serrated bars for mechanical warp stop motions -- Designations of dimensions, and dimensions of cross-section
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard lays down the main dimensions of twin wire healds with inset mail for Jacquard weaving.
Textile machinery and accessories -- Twin wire healds with inset mail for Jacquard weaving
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 366 specifies the dimensions and designation of metal reeds with double-spring baulk for weaving machines.
Textile machinery and accessories -- Reeds -- Part 3: Dimensions and designation of metal reeds with double-spring baulk
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 366 specifies the dimensions and designation of plastic-bound metal reeds for weaving machines. For the strip steel used in the manufacture of dents of reeds, see ISO 9473-1 and 9473-2.
Textile machinery and accessories -- Reeds -- Part 4: Dimensions and designation of plastic-bound metal reeds
- ICS
- 59.120.30
- CCS
- 发布
- 2015-09-03
- 实施
