71.040.10 化学实验室、实验室设备 标准查询与下载

ANSI/TNI EL-V1-2009 试验室实施环境分析用管理和技术要求

Management and Technical Requirements for Laboratories Performing Environmental Analyses

ANSI/TNI EL-V4-2009 环境水平测试提供者授信机构的通用要求

General Requirements for an Accreditor of Environmental Proficiency Test Providers

ASTM E2335-08 实验室监测的标准指南

These guidelines are intended to enable a laboratory monitor to perform onsite assessments of laboratory facilities. Accepted facilities will then participate in an interlaboratory test protocol to establish precision and bias for a particular ASTM standard. This assessment is intended to determine that all of the participants have the necessary equipment, an understanding of the test method, and the minimum level of skill necessary to gather data which are to be used to establish precision and bias for the particular standard. This guide is not intended to be used as a tool to qualify or accredit laboratories to perform any tests. Refer to the Referenced Documents for further guidance on accreditation requirements.1.1 This guide provides a general outline, for use by a laboratory monitor, to assess the qualifications of a laboratory which has requested to participate in a specific ASTM interlaboratory test. 1.2 The preliminary assessment is based on observations made before initiation of any interlaboratory tests. 1.3 The subcommittee, which appoints the laboratory monitor, specifies the minimum requirements which an organization should meet to qualify as a participant for the interlaboratory test. If a pretest is to be included, see details in Section 13. 1.4 This fire standard can not be used to provide quantitative measures. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Laboratory Monitors

CAN/CSA-C22.2 NO.61010-2-040-2007 《测量、控制和实验室用电气设备安全要求》第2-040部分：用于处理医用材料的灭菌器和清洗消毒器的特殊要求（第一版）

Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials (First Edition)

VDI/VDE 3515-2007 用于过程分析技术的电极的多触点插头系统

This Guideline describes the requirements on multicontect connector systems and their realization by a six pin plug. They are directed towards process and labratory applications as well as portable instruments. The guideline applies to in-line analytical measurements in process engineering and considers particularly areas with high demands on operational reliability and corrosion resistance. It specifies the mechanical and electricel requirements to be met by connector systems for electrochemical sensors such as pH and redox electrodes, conductivity probes, potentiometric measurements, and combinations thereof.

Multi-contact plug system for electrodes used in process analysis technology

DL/T 520-2007 火力发电厂入厂煤检测实验室技术导则

本标准规定了火力发电厂入厂煤检测实验室应开展的检测项目、环境(设施)要求、仪器设备的配置及相关技术规范。 本标准适用于火力发电厂入厂煤检测实验室的建立及日常运行时的规范化技术管理。

Technical guidance for coal analytical laboratory in power plant

CNS 15091-14-2007 深层海水检验法－硝酸盐之测定

本标准规定于深层海水硝酸盐之检验。

Method of test for deep sea water - Determination of nitrate

KS L 2300-2007 活塞微量测容积设备

이 규격은 용기에서 다른 용기로 일정량의 용액을 옮길 목적으로, 흡입한 일정량의 용액을 전

Piston operation micro-volumetric apparatus

DIN 12880:2007 实验室电气装置.烘箱和恒温箱

This standard covers non-walk-in heating ovens and incubators suitable for a working temperature range of -10 ℃ to 300 ℃. Incubators also include shaking incubators. The standard gives terms and definitions and specifies performance requirements and tests. Controlled-atmosphere test installations (e.g. as in DIN 50011) and hot air sterilizers are not covered by this standard.

Electrical laboratory devices - Heating ovens and incubators

BS DD CEN/TS 14175-5:2007 通风柜橱 第5部分：安装和维护推荐规范

Fume cupboards. Recommendations for installation and maintenance

BS EN 14175-3:2007 通风橱 第3部分：定型试验方法

Fume cupboards. Type test methods

BS EN 14175-4:2007 通风橱 第4部分：现场试验方法

Fume cupboards. On-site test methods

BS EN 14175-6:2007 通风橱 第6部分：空气体积可变化的通风橱

Fume cupboards. Variable air volume fume cupboards

NF X20-704:2007 2级电子呼吸试验仪.对呼出的空气进行分析以估计乙醇浸透度.规范和试验方法

Class 2 electronic breath tester - Estimation of the alcohol impregnation by analysis of expelled air - Specifications and test methods.

DIN 12924-2:2007 实验室储藏用具 通风橱 第2部分:增加酸和热负荷的通风橱

This standard applies to fume cupboards which are suitable for open digestions (e.g. using perchloric acid, sulphuric acid and/or hydrofluoric acid) and specifies additional requirements to take the increased release of acid or alkali at higher temperatures into consideration.

Laboratory furniture - Fume cupboards - Part 2: Fume cupboards for increased acidic and heat load

DIN CEN/TS 14175-5:2007 通风橱.第5部分:安装和维护推荐标准

This Technical Specification specifies a selection of recommendations for the installation and maintenance of fume cupboards in accordance with EN 14175-2 and EN 14175-6. The maintenance recommendations can be applicable to other fume cupboards as well.

Fume cupboards - Part 5: Recommendations for installation and maintenance; English version CEN/TS 14175-5:2006

YB/T 2305-2007 焦化产品试验用玻璃温度计

本标准规定了焦化产品试验用玻璃温度计的术语与定义、形式和分类、技术规格与要求、检定与使用期限和检查、包装与贮存等内容。 本标准适用于焦化产品试验时测定温度用的玻璃温度计。

Glass thermometers for coking products

LST EN 15154-1-2006 紧急安全淋浴器 第1部分：实验室用管道式淋浴器

Emergency safety showers - Part 1: Plumbed-in body showers for laboratories

LST EN 15154-2-2006 紧急安全淋浴 第2部分：管道式洗眼装置

Emergency safety showers - Part 2: Plumbed-in eye wash units

DIN EN 15154-1:2006 安全性应急冲洗器. 第1部分: 实验室用垂直人体冲洗洗. DIN EN 15154-1: 2006-12的英文版本

This document is a product specification, giving performance requirements for emergency safety body showers connected to the water supply. It is applicable to plumbed-in body showers only, located in laboratory facilities. It is not applicable to emergency safety showers used on industrial sites or in other such areas. Requirements are given in respect of the performance, installation, adjustment and marking of the showers as well as installation, operation and maintenance instructions to be given by the manufacturer. NOTE Attention is drawn to national regulations which may apply in respect of the installation and use of emergency safety showers.

Emergency safety showers - Part 1: Plumbed-in body showers for laboratories; English version of DIN EN 15154-1:2006-12