71.080.01 有机化学综合 标准查询与下载

ASTM E1148-02(2008) 水溶解度测量用标准试验方法

The solubility of organics is a basic physical parameter needed for the prediction of the fate of a chemical in the environment (6). The ionic strength and organic content of natural waters may cause an apparent decrease or increase from the value obtained in pure water. Data on this can be obtained in the laboratory by modifying the reagent water to simulate natural waters.1.1 This test method covers procedures for measurement of the solubility of organic compounds in water. Three procedures are described which will work over a variety of solubility ranges. These procedures are not appropriate for compounds that react with water or air at ambient conditions. 1.2 The procedure chosen will depend on the estimated solubility of the compound. This may be obtained from literature values (see Refs 1, 2, 3) by correlation with other parameters (4) or by analogy with the solubility of similar compounds. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurements of Aqueous Solubility

TIS 1921-1999 工业用挥发性有机液体.水浴蒸发后干残余物的测定.一般方法

Volatile organic liquids for industrial use.determination of dry residue after evaporation on a water bath.general method

ASTM E659-78(2000) 液体化学品自燃温度的标准试验方法

Standard Test Method for Autoignition Temperature of Liquid Chemicals

ANSI/ASTM D6506:2000 普通丙基溴化物含量评估试验方法

This specification covers an asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. The protection board protects the waterproofing system from backfill, surfacing, construction activities, and weathering conditions prior to backfilling or applying surfacing. The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Assay of Normal-Propyl Bromide Content

ANSI/ASTM D6065:2000 Hfc-227ea 1, 1, 1, 2, 3, 3, 3-七氟丙烷的搬运、运输和储存惯例

This practice covers guidance and direction to suppliers, reclaimers, purchasers, and users in the handling, transportation, and storage of HFC-227ea. The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Handling, Transportation and Storage of Hfc-227ea 1, 1, 1, 2, 3, 3, 3-Heptafluoropropane (Cf3 Chfcf3)1

ANSI/ASTM D6541:2000 HFC-236fa, 1, 1, 1, 3, 3, 3-六氟丙烷(Cf3ch2cf3)1规范

This specification covers the requirements for HFC-236fa as a fire-fighting medium. This specification does not address the fire-fighting equipment or hardware that employs HFC-236fa or the conditions of employing such equipment (for example, hand-helds, fixed installations, and so forth). This specification does not address the storage or transportation of HFC-236fa. Storage, handling, and transportation issues are addressed in Practice D 6427. The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only 。The following safety hazards caveat pertains to the test methods portion, Section 6.1, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 4.3.

Specification for HFC-236fa, 1, 1, 1, 3, 3, 3-Hexafluoropropane (Cf3ch2cf3)1

HG/T 2971-1999 工业甲胺水溶液试验方法

本标准规定了工业甲胺水溶液的试验方法。 本标准适用于甲醇连续气相催化氨化法生产的甲胺配制的水溶液的测定。

Solutions of methylamines for industrial use-Standard test method

ASTM E324-99 有机化合物的相对始熔点及终熔点和熔化范围的标准试验方法

1.1 This test method covers the determination, by a capillary tube method, of the initial melting point and the final melting point, which define the melting range, of samples of organic chemicals whose melting points without decomposition fall between 30 and 250176C. 1.2 This test method is applicable only to crystalline materials that are sufficiently stable in storage to meet the requirements of a satisfactory standard sample as defined in Section 6. 1.3 This test method is not directly applicable to opaque materials or to noncrystalline materials such as waxes, fats, and fatty acids. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Relative Initial and Final Melting Points and the Melting Range of Organic Chemicals

ANSI/ASTM D6427:1999 HFC-236fa, 1, 1, 1, 3, 3, 3-六氟丙烷的搬运、储存和运输惯例

This practice covers guidance and direction to suppliers, purchasers, and users in the handling, transportation, and storage of HFC-236fa. The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practices for Handling, Transportation, and Storage of HFC-236fa, 1, 1, 1, 3, 3, 3-Hexafluoropropane, CF3CH2CF3

ANSI/ASTM D6437:1999 聚氨酯生胶材料试验方法：低碱聚合溶胶碱性测定

This test method covers measuring alkalinity in low-alkalinity (0.002 meq/g basicity) polyols. This alkalinity is often expressed as CPR (controlled polymerization rate) of polyether polyols. This test method is not applicable to amine-based polyols. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There is no similar or equivalent ISO standard.

Test Methods for Polyurethane Raw Materials: Alkalinity in Low-Alkalinity Polyols (Determination of CPR Values of Polyols)

ANSI/ASTM D6231:1998 五氟甲烷(HFC-125)规范,C2HF51

This specification covers the requirements for HFC-125 as a fire-fighting medium. This specification does not address the fire-fighting equipment or hardware that employs HFC-125 or the conditions of employing such equipment, for example, hand helds, fixed installations, etc. This specification does not address the storage or transportation of HFC-125. Storage, handling, and transportation issues are addressed in Practice D 6268. The following safety hazards caveat pertains to the test methods portion, Section 6, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 4.3.

Specification for HFC-125 (Pentafluoroethane), C2HF51

NAVY MIL-M-81999 A NOTICE 1-1997 飞机非致癌物质固化聚氨酯抗逆转模塑化合物的结构

This notice should be filed in front of MIL-M-8 19994 dated 20 July 1977 MIL-M-8 1999A is inactive for new design and is no longer used, except for replacement purposes.

MOLDING COMPOUND, REVERSION RESISTANT, NON- CARCINOGEN CURING POLYURETHANE, AIRCRAFT STRUCTURE

ANSI/ASTM D6127:1997 三氟甲烷 HFC-23 的搬运、运输和储存惯例

This practice covers guidance and direction to suppliers, purchasers, and users in the handling, transportation, and storage of HFC-23. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Handling, Transportation, and Storage of HFC-23 (Trifluoromethane, CHF3)

ANSI/ASTM D5248:1996 可回收1, 1, 2-三氯乙烷 1, 2, 2-三氯三氟乙烷规范

This specification covers the three grades of 1, 1, 2-trichloro 1, 2, 2-trifluoroethane typically needed in various industries. It may be used as a reference document by purchasers or by persons establishing in-house, 1, 1, 2-trichloro 1, 2, 2-trifluoroethane recovery programs.

Specification for Reclaimed 1, 1, 2-Trichloro 1, 2, 2-Trifluoroethane

ANSI/ASTM D2988:1996 卤化有机溶剂或其搀合物中水溶性卤化物离子测试方法

Test Methods 1, 2, and 3 -These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride. Test Method 4 - This test method covers the determination of chloride ion in halogenated organic solvents and their admixtures. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.

Test Method for Water-Soluble Halide Ion in Halogenated Organic Solvents and their Admixtures

HG/T 2717-1995 工业过氧化苯甲酰

本标准规定了工业过氧化苯甲酰的技术要求，试验方法、检验规则、标志、包装、运输、贮存。 分子式：(C|(6)H|(5)CO)|(2)O|(2) 相对分子质量：242.22(按1991年国际相对原子质量)

Industrial Benzoyl Peroxide

HG/T 2706-1995 聚酯多元醇命名

本标准规定了已二酸系聚酯多元醇命名的组成及表示方法，本命名方法根据聚酯多元醇所用原料种类、特征性能、主要用途进行命名。 本标准适用于聚氨酯用饱和聚酯多元醇的分类命名。

Polyester polyol nomenclature

HG/T 2707-1995 聚酯多元醇规格

本标准规定了聚酯多元醇的技术要求、试验方法、检验规则及标志、包装、运输、贮存等要求。 本标准适用于已二酸与低分子多元醇经缩聚反应制得的聚酯多元醇。

Polyester Polyol Specifications

ASTM D5350-95(2012) 用滴定法测定有机合成硫酸酐的标准试验方法.试验方法A

This test method is intended for the determination of organically combined sulfuric anhydride in sulfated oils.1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by boiling the sample with sulfuric acid and determining the acidity of the reaction mixture. This test method is applicable only to oils that split off their combined SO3 upon boiling with mineral acids and that do not contain compounds that cannot be accurately titrated in water solution with methyl orange as the indicator. This test method was derived from Test Methods D500, Sections 15 through 19. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Titration, Test Method A

ASTM D5352-95(2012) 用灰分重量分析法测定有机合成硫酸酐的标准试验方法.试验方法C

This test method is intended for the determination of organically combined sulfuric anhydride in sulfonated and sulfated fats and oils.1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfonated or sulfated oil, or both, by extracting the undecomposed sulfonated or sulfated fat and other fatty matter over an acidulated, concentrated salt solution, and ashing the purified extract. This test method is applicable to all types of sulfonated and sulfated oils, including true sulfonic acid oils and those containing sodium acetate or similar partially titratable compounds. This test method was derived from Test Methods D500, Sections 25 through 28. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C