71.080.10 脂族烃 标准查询与下载

T/CIESC 0020-2022 聚合级乙烯、丙烯中砷化氢和磷化氢的测定 气相色谱-质谱法

本文件规定了用气相色谱-质谱联用法测定聚合级乙烯、丙烯中砷化氢和磷化氢的含量。 本文件适用于砷化氢和磷化氢含量不低于0.01 mL/m3的聚合级乙烯、丙烯的测定。 

Standard Test Method for Arsine and Phosphine in Polymer Grade Ethylene and Propylene by Gas Chromatography-Mass Spectrometry

T/CIESC 0021-2022 聚合级乙烯、丙烯中永久气体的测定气相色谱-氦离子化检测器法

本文件规定了用配备氦离子化检测器的气相色谱仪测定聚合级乙烯、丙烯中永久气体（氢气、氮气、氧气、甲烷、一氧化碳和二氧化碳）的方法。 本文件适用于氢气含量不低于0.1mL/m3，氮气含量不低于0.05mL/m3，氧气含量不低于0.05mL/m3，甲烷含量不低于0.05mL/m3，一氧化碳含量不低于0.05mL/m3，二氧化碳含量不低于0.05mL/m3的聚合级乙烯、丙烯的测定。

Standard Test Method for Permanent Gases in Polymer Grade Ethylene and Propylene by Gas Chromatography and Helium Ionization Detector

ASTM D5134-21 毛细管气相色谱法通过正壬烷对石油石脑油进行详细分析的标准试验方法

1.1 This detailed hydrocarbon analysis (DHA) test method covers the determination of hydrocarbon components paraffins, naphthenes, and monoaromatics (PNA) of petroleum naphthas as enumerated in Table 1. Components eluting after n-nonane (bp 150.8 °C) are determined as a single group. 1.2 This test method is applicable to olefin-free (C7. 1.5 Detailed hydrocarbon components in olefin containing samples may be determined by DHA Test Methods D6729, D6730, or D6733. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 8. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography

ASTM D2268-21 毛细管气相色谱法分析高纯度正庚烷和异辛烷的标准试验方法

1.1 This test method covers and provides for the analysis of high-purity (greater than 99.5 % by volume) n-heptane and isooctane (2,2,4-trimethylpentane), which are used as primary reference standards in determining the octane number of a fuel. Individual compounds present in concentrations of less than 0.01 % can be detected. Columns specified by this test method may not allow separation of all impurities in reference fuels. 1.2 The values stated in SI units are to be regarded as the standard. 1.2.1 Exception—The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography

ASTM D3131-07(2021) 乙酸异丙酯（99%级）标准规范

1.1 This specification covers isopropyl acetate (99 % grade). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 For specific hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification. 1.4 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Isopropyl Acetate (99 % Grade)

ASTM D1836-07(2021) 商用己烷的标准规范

1.1 This specification covers the range of products commonly referred to as hexanes, which find uses in the preparation of adhesives, coatings, and printing inks, as raw materials in chemical synthesis operations, and as solvents in various kinds of extraction operations. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 For specific hazard information and guidance consult supplier’s Material Safety Data Sheet. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Commercial Hexanes

T/CPCIF 0117-2021 工业用甲基环己烷

项    目　要    求 　优级品　一等品　合格品  外观　无色透明液体，无明显可见水，无机械杂质及絮状物  色度（铂-钴色号）/Hazen单位             ≤　5　10　10  甲基环己烷含量，w/%                    ≥　99.8　99.8　99.5  环己烷含量，w/%                        ≤　0.01　0.03　0.10  苯含量，w/%                            ≤　0.000 1　0.000 2  甲苯含量，w/%                          ≤　0.001 0　0.001 5  水分，w/%                              ≤　0.03　0.10　0.10

Methylcyclohexane for industrial use

HG/T 5823-2021 煤基费托合成 固体蜡

Coal-based Fischer-Tropsch synthetic solid wax

HG/T 5822-2021 煤基费托合成 混合烯烃

Coal-based Fischer-Tropsch synthesis of mixed olefins

KS M 1677-2020 环氧乙烷

Ethylene oxide

KS M 1049-2020 高纯度庚烷

High purity heptane

KS M 1048-2020 高纯度正己烷

High purity n-Hexane

KS M 1051-2020 高纯度十一烷

High purity undecane

KS M 1511-2020 丙二醇

Propylene glycol

SH/T 1482-2020 工业用异丁烯纯度及烃类杂质的测定 气相色谱法

Determination of purity and hydrocarbon impurities of isobutylene for industrial use by gas chromatography

SH/T 1549-2020 工业用轻质烯烃中水分的测定 在线分析仪使用导则

Guidelines for the use of online analyzers for the determination of moisture in industrial light olefins

SH/T 1492-2020 工业用1-丁烯纯度及烃类杂质的测定 气相色谱法

Determination of purity and hydrocarbon impurities of 1-butene for industrial use by gas chromatography

SH/T 1142-2020 工业用裂解碳四 液态采样法

Industrial cracked carbon four-liquid sampling method

SH/T 1483-2020 工业用碳四烯烃中微量含氧化合物的测定 气相色谱法

Isobutene for industrial use--Determination of oxy-compounds--Gas chromatographic method

T/GPCIA 0003-2020 多烷基苯合成油

多烷基苯合成油的技术要求和试验方法见表1。 表1　技术要求与试验方法 项目　指标　试验方法 　PAB-2　PAB-3　PAB-4　PAB-5　PAB-6　PAB-8　PAB-10　 外观　清澈透明，无悬浮物　目测 倾点/℃                    不高于　-50　-50　-50　-45　-40　-40　-35　GB/T 3535 运动黏度（40℃）/(mm2/s)　报告　报告　18.0～ 23.0　25.0～35.0　报告　报告　报告　GB/T 265 运动黏度（100℃）/(mm2/s)　1.9～2.5　2.6～3.5　3.6～ 4.2　4.3～ 5.5　5.6～7.0　7.5～8.5　9.0～10.5　 黏度指数　报告　GB/T 1995 水分（质量分数）/(%)，     不大于　痕迹　GB/T 260 机械杂质（质量分数）/(%) ，不大于　0.01　GB/T 511 密度（20℃）a /(kg/m3)　840～880　GB/T 1884  闪点（开口）/℃，          不低于　160　170　190　210　220　220　230　GB/T 3536 苯胺点/℃，                不高于　75　90　100　GB/T 262 铜片腐蚀（100℃,3h）/级，  不大于　1　GB/T 5096 残炭（质量分数）/(%)，     不大于　0.1　GB/T17144 低温动力黏度 (-30℃) / (mPa?s)，不大于　——　——　——　报告　报告　4500　——　GB/T 6538 蒸发损失（250℃,1h）/(%)，  不大于　——　报告　报告　18　14　10　8　SH/T 0059 自燃点/℃　报告　报告　报告　——　——　——　——　SH/T 0642 酸值/（mgKOH/g），          不大于　0.2　GB/T 7304 氧化安定性　旋转氧弹法b（150℃） /min，不小于　报告　报告　报告　报告　报告　200　180　SH/T 0193 　PDSC法（150℃）/min 　报告　报告　报告　报告　报告　报告　报告　SH/T 0719 氯含量/（mg/kg），          不大于　10　GB 23971- 2009 附录B 红外图谱　烷基苯特征波峰与标准图谱一致c　GB/T 32199 a密度也可按照SH/T 0604检测，如有异议以GB/T 1884作为仲裁方法。 b样品加入0.8%（质量分数）的T501，将油样均匀加热到50℃～60℃，充分搅拌至均匀，冷却后测试氧化安定性。 c烷基苯标准图谱见附录A。

Polyalkyl benzene synthetic oil