71.080.60 (Alcohols. Ethers) 标准查询与下载

ASTM D3125-97(2001) 无色单体丙烯酸酯和丙烯酸中的氢醌一甲基醚的标准试验方法

1.1 This test method covers the determination of monomethyl ether of hydroquinone (MEHQ) in colorless monomeric acrylate esters and acrylic acid. The test method is applicable to the determination of MEHQ in the concentration range from 0 to 1200 parts per million. 1.2 For hazard information and guidance, see the supplier''s Material Safety Data Sheet. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.

Standard Test Method for Monomethyl Ether of Hydroquinone in Colorless Monomeric Acrylate Esters and Acrylic Acid

ASTM E1119-97(2002) 工业级乙二醇

1.1 This specification covers industrial grade ethylene glycol.The following precautionary caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.2 Review the current Materials Safety Data Sheets (MSDS) for detailed information concerning toxicity, first aid procedures, handling and safety precautions.

Standard Specification for Industrial Grade Ethylene Glycol

ASTM D304-95(1999) 用氧离子滴定法合成阴离子配合剂的标准试验方法

1.1 This specification covers n-butyl alcohol (butanol). 1.2 For hazard information and guidance, see the supplier''s Material Safety Data Sheets.

Standard Specification for n-Butyl Alcohol (Butanol)

ASTM D770-95(1999) 测量药瓶和水泡包装水蒸气透过性(WVTR)的标准试验方法

1.1 This specification covers isopropyl alcohol (99% grade). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 For hazard information and guidance, see the supplier''s Material Safety Data Sheet.

Standard Specification for Isopropyl Alcohol

ASTM D3622-95(2000)e1 1-丙醇标准规范(正丙醇)

1.1 This specification covers n-propyl alcohol (1-propanol) for use in paint, varnish, lacquer and related products. 1.2 For specific hazard information and guidance, see the supplier''s Material Safety Data Sheets for materials listed in this specification.

Standard Specification for 1-Propanol (n-Propyl Alcohol)

ASTM D331-95(1999) 使用英国轮加速抛光骨料的标准做法

1.1 This specification covers 2-ethoxyethanol. 1.2 For hazard information and guidance, see the supplier''s Material Safety Data Sheets.

Standard Specification for 2-Ethoxyethanol

ASTM D1719-95(1999) 异丁醇的标准规范

1.1 This specification covers isobutyl alcohol for use in paint, varnish, lacquer, and related products. 1.2 For specific hazard information and guidance, see the supplier''s Material Safety Data Sheets for materials listed in this specification.

Standard Specification for Isobutyl Alcohol

ASTM D319-95(1999) 戊醇(合成)标准规范

1.1 This specification covers synthetic amyl alcohol. 1.2 For hazard information and guidance, see the supplier''s Material Safety Data Sheet.

Standard Specification for Amyl Alcohol (Synthetic)

ASTM D4794-94(1998) 使用气相色谱法测定纤维素醚产品中的乙氧基或羟基乙氧基置换的标准试验方法

1.1 This test method is applicable to the determination of ethoxyl or hydroxyethoxyl substitution in cellulose ether products by a Zeisel gas chromatographic technique. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5 and Note 3.

Standard Test Method for Determination of Ethoxyl or Hydroxyethoxyl Substitution in Cellulose Ether Products by Gas Chromatography

ASTM D4794-94(2003) 用气相色谱法测定纤维素醚产品中羟乙基替代物的标准试验方法

1.1 This test method is applicable to the determination of ethoxyl or hydroxyethoxyl substitution in cellulose ether products by a Zeisel gas chromatographic technique.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5 and Note 3.

Standard Test Method for Determination of Ethoxyl or Hydroxyethoxyl Substitution in Cellulose Ether Products by Gas Chromatography

ASTM D5441-93 通过气相色谱法分析甲基叔丁基醚(MTBE)的标准试验方法

1.1 This test method provides for determination of the purity of methyl tert-butyl ether (MTBE) by gas chromatography. It also provides a procedure to measure impurities in MTBE such as C 4 to C 12 olefins, methyl, isopropyl and tert-butyl alcohols, methyl sec-butyl and methyl tert-amyl ethers, acetone, and methyl ethyl ketone. Impurities are determined to a minimum concentration of 0.02 mass %. 1.2 This test method is not applicable to the determination of MTBE in gasoline. 1.3 Water cannot be determined by this test method and must be measured by a procedure such as Test Method D1364 and the result used to normalize the chromatographic values. 1.4 A majority of the impurities in MTBE is resolved by the test method, however, some co-elution is encountered. 1.5 This test method is inappropriate for impurities that boil at temperatures higher than 180176C or for impurities that cause poor or no response in a flame ionization detector, such as water. 1.6 The values stated in SI (metric) units of measurement are preferred and used throughout the standard. Alternate units, in common usage, are also provided to improve clarity and aid the user of this method. 1.7 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography

ASTM D330-93(2001) 2-丁氧基乙醇的标准规范

1.1 This specification covers 2-butoxyethanol. 1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for 2-Butoxyethanol

ASTM D4835-93(1998) 丙二醇－甲基醚乙酸酯

1.1 This specification covers propylene glycol monomethyl ether acetate (PMA). Note-Propylene glycol monomethyl ether acetate (PMA) is a mixture of 1-methoxy-2-acetoxypropane and 2-methoxy-1-acetoxypropane. 1.2 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet for materials listed in this standard.

Standard Specification for Propylene Glycol Monomethyl Ether Acetate

ASTM E1147-92(1997) 用液体色谱法估算分配系数(N-辛醇/水)的试验方法

1.1 This test method describes a procedure for the estimation of the log of the octanol/water partition coefficient (log Kow ) of chemicals over the range from 0 to 8. 1.2 This test method uses an empirically derived equation to relate the octanol/water partition coefficient to an experimentally determined retention time on a liquid chromatographic column. 1.3 This test method has been designed to estimate log Kow values for both non-ionizable and ionizable compounds. This is accomplished by buffering the liquid chromatographic solvent at a pH that will force the test compound into either the non-ionized or ionized form. 1.4 This test method requires some knowledge of the detector response to the chemical being tested. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Partition Coefficient (N-Octanol/Water) Estimation by Liquid Chromatography

ASTM D5164-91(2000) 丙二醇和二丙二醇的标准规范

1.1 This specification covers propylene glycol and dipropylene glycol for use in the preparation of surface coatings. 1.2 For specific hazard information and guidance, see the supplier''s Material Safety Data Sheets.

Standard Specification for Propylene Glycol and Dipropylene Glycol

ASTM D1257-90(2001) 高比重甘油

1.1 This specification covers high-gravity glycerin (98.7 weight%, minimum) for use in the manufacture of alkyd and other synthetic resins. 1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for High-Gravity Glycerin

ASTM E1075-85(1997) 乙二醇,二甘醇,三甘醇,丙二醇和二丙二醇的气味以及丙二醇的味道的标准试验方法

1.1 These test methods cover procedures for observing odors of glycols and estimating their odor acceptability. These test methods apply to ethylene, diethylene, triethylene, propylene, and dipropylene glycols. A method for observing the taste and estimating the intensity of the taste of propylene glycol is also included. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Odor of Ethylene Glycol, Diethylene Glycol, Triethylene Glycol, Propylene Glycol, and Dipropylene Glycol and Taste of Propylene Glycol