71.080.80 醛和酮 标准查询与下载
共找到 220 条与 醛和酮 相关的标准，共 15 页
Scope is not provided for this standard
Formaldehyde solutions for industrial use -- Determination of formaldehyde content
- ICS
- 71.080.80
- CCS
- 发布
- 2015-12-21
- 实施
Aqueous solution of glyoxal for industrial use
- ICS
- 71.080.80
- CCS
- G17
- 发布
- 2015-04-13
- 实施
- 2015-06-01
Formaldehyde solution(formalin)for industrial use
- ICS
- 71.080.80
- CCS
- 发布
- 2014-09-26
- 实施
稠环重芳烃的要求、试验方法、检验规则、标志、包装、运输、贮存及安全等。
Polycyclic Heavy Aromatics
- ICS
- 71.080.80
- CCS
- C2614
- 发布
- 2014-09-19
- 实施
- 2016-05-13
Methyl ethyl ketone for industrial use－Examination for residual odour
- ICS
- 71.080.80
- CCS
- 发布
- 2013-12-30
- 实施
本标准规定了工业用异丁醛的要求、试验方法、检验规则、标志、包装、运输、贮存及安全等。 本标准适用于由丙烯、氢气、一氧化碳羰基化制得的工业用异丁醛。该产品主要用于合成泛酸、氨酸、亮氨酸、纤维素脂、香料、增塑剂、树脂及汽油添加剂。 分子式：(CH3)2CHCHO 相对分子质量：72.152（按2012年国际相对原子质量）
Isobutyraldehyde for industrial use
- ICS
- 71.080.80
- CCS
- G17
- 发布
- 2013-06-13
- 实施
- 2013-07-10
1.1 This specification covers methyl n-amyl ketone (98 % grade) for use in paint, varnish, lacquer, and related products.1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
Standard Specification for Methyl n-Amyl Ketone
- ICS
- 71.080.80
- CCS
- 发布
- 2011-11-01
- 实施
High density polyethylene (HDPE) as a raw material for drinking water pipes
- ICS
- 71.080.80
- CCS
- 发布
- 2010
- 实施
The determination of the carbonyl content of polymerization-grade 1,3-butadiene is necessary, since in some polymerization reactions, the presence of carbonyls in excess over some specified amount can have a deleterious effect upon the polymer properties or the reaction itself, or both.1.1 This test method covers the determination of carbonyls (ketones and aldehydes) in C4 hydrocarbons. This test method was tested on polymerization-grade 1,3-butadiene. 1.2 The applicable range for this test method is 0 to 50 mg/kg carbonyls calculated as acetaldehyde. 1.3 Other C4 hydrocarbons and their mixtures besides polymerization-grade 1,3-butadiene could be tested using this same test method. However, the precision section of this test method covers only carbonyls in applicable range as listed in 1.2, as found in polymerization-grade 1,3-butadiene. 1.4 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determination of Carbonyls In C
- ICS
- 71.080.80
- CCS
- G16
- 发布
- 2010
- 实施
Acetaldehyde for industrial use－Determination of total content of carbonyl compounds－Volumetric method
- ICS
- 71.080.80
- CCS
- 发布
- 2009-09-04
- 实施
Acetaldihyde for industrial use－Determination of water content－Karl fischer method
- ICS
- 71.080.80
- CCS
- 发布
- 2009-09-04
- 实施
Formaldehyde solutions for industrial use－Limit test for heavy metals (excluding iron)
- ICS
- 71.080.80
- CCS
- 发布
- 2009-09-04
- 实施
Formaldehyde solutions for industrial use－Limit test for inorganic chlorides
- ICS
- 71.080.80
- CCS
- 发布
- 2009-09-04
- 实施
