71.100.20 工业气体 标准查询与下载

JB/T 8693-2015 大中型空气分离设备

本标准规定了大中型空气分离设备(以下简称空分设备)的术语和定义、产品分类和型号、技术要求、出厂检验、现场检验、标志、包装、运输和贮存。 本标准适用于氧气产量大于或等于1 000 m/h且小于60 000 m/h，以低温法分离空气制取氧、氮及氩产品的空分设备。 特大型空气分离设备可参照本标准执行。

Large and medium scale air separation plants

GSO ISO 10298:2015 确定气体或气体混合物的毒性

This International Standard lists the best available acute-toxicity data of gases from the literature to allow the classification of gases and gas mixtures.

Determination of toxicity of a gas or gas mixture

T/ZZB 009-2015 深冷法空气分离设备

本标准规定了深冷法空气分离设备（以下简称空分设备）的组成及型号、技术要求、检验检测、标志、包装、运输及贮存、安装要求。 本标准适用于以深冷法分离空气制取氧、氮及氩等稀有气体产品的空分设备。

Cryogenic air separation unit

ASTM D2713-15e1 丙烷干燥标准试验方法（阀门冷冻法）

1.1 This test method covers the measurement of the dryness of propane products that do not contain antifreeze agents such as, but not limited to, commercial propane and special duty propane (see Specification D1835). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Dryness of Propane (Valve Freeze Method)

SJ/T 11517-2015 电子工业用气体 一氧化碳

本标准规定了一氧化碳的技术要求,试验方法以及包装、标志、贮运及安全。本标准适用于甲酸脱水、甲酸甲酯选择分解、木炭还原二氧化碳、甲醇裂解或使用天然气、轻油、重质液态烃、焦炭、煤等含碳物质为原料经过氧化、蒸汽转化或二氧化碳还原等不同工艺过程获得并经精制得到的一氧化碳产品。它在多晶态钻石膜生产中,为化学气相沉积(CVD)工艺过程提供碳源。分子式:CO相对分子质量:28.0101 (按2007年国际相对原子质量计算)

Gases for electronic industry-Carbon monoxide

DB34/T 1544-2015 C4混合液

本标准规定了 C4 混合液的要求、检验规则、标志、包装、运输、贮存、交货验收。 本标准适用于以 C4 残液为原料，添加气化剂、催化剂、除炭剂等，经加工制成的 C4 混合液。

C4 mixture

ASTM D2713-15 丙烷干燥性的标准试验方法 (阀门冷冻法)

5.1 This test is a functional test in which the water concentration in the product is related to product behavior characteristics in a pressure-reducing system of special design to arrive at a measure of product acceptability in common use applications. Experience has demonstrated that excessive water content (dissolved water) will cause freeze-up difficulties in pressure reducing systems. 1.1 This test method covers the measurement of the dryness of propane products that do not contain antifreeze agents such as, but not limited to, commercial propane and special duty propane (see Specification D1835). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Dryness of Propane (Valve Freeze Method)

GSO ISO 13338:2014 确定气体或气体混合物的组织腐蚀

This International Standard gives — for pure gases: a complete list indicating their corrosiveness, — for gas mixtures: a calculation method, in the absence of experimental data, relating to the corrosiveness of each of their components, in order to determine the corrosiveness of gases and gas mixtures on tissue so that a suitable outlet connection can be assigned to each of them.

Determination of tissue corrosiveness of a gas or gas mixture

DB35/T 1442-2014 基于RFID 的车用气瓶数字化管理规范

本标准规定了车用气瓶的术语和定义、气瓶电子标签、手持读写器、加气站级管理系统、公司级管理系统。 本标准适用于基于RFID的车用数字化气瓶管理的加气站和相关管理单位。

Digital management specification for vehicle gas cylinders based on RFID

GSO 564:2014 气体 医用氧气 测试方法

This GSO standard is concerned with test methods of medical oxygen gas used for medical purposes

Gases – Medical Oxygen Gas - Test methods

JB/T 11847-2014 透平膨胀机 技术条件

本标准规定了透平膨胀机的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于空气及天然气分离与液化过程中膨胀做功获得冷量的向心式透平膨胀机（以下简称膨胀机）。 本标准不适用于气体轴承、电磁轴承透平膨胀机及工质温度超过300℃的热气透平膨胀机。

Specifications for turbo expanders

BS ISO 14687-3:2014 氢燃料. 产品规范. 固定器具用质子交换膜 (PEM) 燃料电池应用

Hydrogen fuel. Product specification. Proton exchange membrane (PEM) fuel cell applications for stationary appliance

ISO 14687-3:2014 氢燃料.产品规格.第3部分:固定电器用质子交换膜(PEM)燃料电池的应用

This partofISO 14687 specifiesthe quality characteristics ofhydrogen fuel in orderto ensure uniformity of the hydrogen product for utilization in stationary proton exchange membrane (PEM)] fuel cell power Systems，

Hydrogen fuel - Product specification - Part 3: Proton exchange membrane (PEM) fuel cell applications for stationary appliances

ANSI/CSA CHMC1-2014 压缩氢气应用设施中评估材料兼容性的试验方法

Test Method for Evaluating Material Compatibility in Compressed Hydrogen Applications

GOST R 56248-2014 液体氢. 规格

Liquid hydrogen. Specifications

GSO ISO 8573-8:2013 压缩空气 第8部分：固体颗粒质量含量试验方法

This part of ISO 8573 specifies test methods for determining the solid particle mass concentration in compressed air, expressed as the mass of solid particles with maximum particle size limits. The limitations of the methods are also given. One of a series of standards aimed at harmonizing air contamination measurements, it identifies sampling techniques and also gives requirements for evaluation, uncertainty considerations and reporting for the air purity parameter solid particles by mass concentration. The test methods are suitable for determining purity classes in accordance with ISO 8573-1. (Particle content based on counting particles is dealt with in ISO 8573-4.)

Compressed air -- Part 8: Test methods for solid particle content by mass concentration

GSO ISO 8573-7:2013 压缩空气 第7部分：活性微生物污染物含量试验方法

This part of ISO 8573 specifies a test method for distinguishing viable, colony-forming, microbiological organisms (e.g. yeast, bacteria, endotoxins) from other solid particles which may be present in compressed air. One of a series of standards aimed at harmonizing air contamination measurements, it provides a means of sampling, incubating and determining the number of microbiological particles. The test method is suitable for determining purity classes in accordance with ISO 8573-1, and is intended to be used in conjunction with ISO 8573-4 when there is need to identify solid particles that are also viable, colony-forming units.

Compressed air -- Part 7: Test method for viable microbiological contaminant content

GSO ISO 8573-4:2013 压缩空气 第4部分：固体颗粒含量试验方法

This part of ISO 8573 provides a guide for choosing a suitable method to determine the solid particle concentration in compressed air, expressed as the number of solid particles in respective size classes. It describes the limitations of the various methods. This part of ISO 8573 identifies sampling techniques and measurement methods based on the counting of particles, and describes the evaluation, uncertainty considerations and reporting of the air purity parameter, solid particles. NOTE 1 The test methods described in this part of ISO 8573 are those suitable for determining the purity classes given in ISO 8573-1. NOTE 2 Particle content determined as mass concentration is dealt with in ISO 8573-8.

Compressed air -- Part 4: Test methods for solid particle content

GSO ISO 8573-9:2013 压缩空气 第9部分：液态水含量试验方法

This part of ISO 8573 specifies test methods for determining the liquid water content in compressed air, expressed as the liquid water mass concentration. The limitations of the methods are also given. One of a series of standards aimed at harmonizing air contamination measurements, it identifies sampling techniques and also gives requirements for evaluation, uncertainty considerations and reporting for the air purity parameter liquid water. The test methods are suitable for determining the purity classes in accordance with ISO 8573-1.

Compressed air -- Part 9: Test methods for liquid water content

GSO ISO 8573-1:2013 压缩空气 第1部分：污染和纯度分类

This part of ISO 8573 specifies purity classes of compressed air with respect to particles, water and oil, independent of the location in the compressed air system at which the air is specified or measured. This part of ISO 8573 provides general information about contaminants in compressed air systems as well as links to the other parts of ISO 8573, either for the measurement of compressed air purity or the specification of compressed air purity requirements. In addition to the above-mentioned contaminants of particles, water and oil, this part of ISO 8573 also identifies gaseous and microbiological contaminants. Guidance is given in Annex A as to the application of this part of ISO 8573.

Compressed air -- Part 1: Contaminants and purity classes