71.120.10 反应容器及其组件 标准查询与下载

DIN 7080:2005 低温范围内无限制的硼硅酸盐玻璃制抗压圆形视孔玻璃

The document is applicable to thermally prestressed circular sight glasses of borosilicate glass which can be subjected to permanent liquid or gas pressure on one side at temperatures up 280 ? Under specifies conditions, application up tp 300 ?is practicable (permitted).#,,#

Pressure resistant circular sight glasses of borosilicate glass without limitation in the range of low temperature

DIN 28137-2:2005 搅拌器用安装凸缘.第2部分:玻璃内衬容器用E型安装凸缘

The project is to be used for agitator flanges for glass lined agitator vessels. Only the connecting dimensions are described.

Mounting flanges for agitation units - Part 2: Typ E for glass lined vessels

DIN 28140-2:2005 排泄阀用连接件.第2部分:搪玻璃钢件.连接尺寸PN10

The project is valid for connections for discharge valves and fittings for glass lined steel vessels with PN number 10.

Connections for bottom discharge valves - Part 2: On glass lined steel; connecting dimensions PN 10

DIN 28140-1:2005 排泄阀用连接件.第1部分:非合金钢、不锈钢或有衬钢.尺寸配合PN10

The project applies to the connections of bottom discharge valves of carbon steel, stainless steel and steel, with lining.

Connections for bottom discharge valves - Part 1: Non alloyed, stainless or lined steel; dimensions mating PN 10

DIN 28137-1:2005 搅拌器用安装凸缘.第1部分:非合金和不锈钢容器用

Mounting flanges for agitation units - Part 1: For vessels of non-alloyed and stainless steel

DIN 28120:2004 主动力连接中的有罩圆形观察孔

This standard is applicable to circular sight glasses with case in main power connection with metal melted glas according to DIN 7079-1 and borosilicate glass according to DIN 7080. Scope: Maximum allowable pressure of 10 bar and 16 bar at a maximum allowable temperature of 300 ? For maximum allowable temperatures less than -10 ?the AD-2000-MerkblattW 10 shall be considered.

Circular sight glasses with case in main power connection

DIN 28121:2004 金属与金属接触式法兰连接中的有罩圆形观察孔

This standard is applicable to mounted flanged holders for circular sight glass plates with borosilicate glass according to DIN 7080 in metal to metal contact type flanged joint. Scope: Maximum allowable pressure of 10 bar and 25 bar at a maximum allowable temperature of 200 ? For maximum allowable temperatures less than -10 ?the AD-2000-MerkblattW 10 shall be considered.

Circular sight glasses with case in metal to metal contact type flanged joint

DIN 28141:2003 非合金钢和不锈钢制容器和加工器具用连接法兰

The project applies to connecting flanges for vessels and process apparatus made of non-alloy and stainless steel, e.g. for agitator vessels in accordance with DIN 28136-1. Connecting flanges are joining agitator flanges in accordance with DIN 28137-1 to agitator glas stools in accordance with DIN 28162-1 and -2 enabling the connection to agitators with shaft ends in accordance with DIN 28154 or DIN 28156 as the bases for mechanical seals in accordance with DIN 28138-1 or packing glands in accordance with DIN 28163. The component connecting flange allows for the combination of an agitator flange with various mechanical seals or packing glands graded according to shaft diameters and with various agitator gear stools graded according to gear stool nominal size.#,,#

Connecting flanges for vessels and process apparatus of non-alloy and stainless steel

DIN 28081-1:2003 容器的管式底脚.尺寸

This standard applies to tubular supports with reinforcing plate for vertical vessels. The maximum load forces for the vessel ends can be taken from DIN 28081-3. These load forces apply to vessels operated without pressure or with internal overpressure. The pressure/temperature ratings are also considered therein. This draft standard describes a selection of various shapes and dimensions of supports. The apparatus manufacturer shall provide a proof of strength and stability.

Tubular supports for vessels - Dimensions

DIN 28080:2003 卧式器具鞍形支座.尺寸

This standard applies to saddle supports with saddle plates for horizontal apparatus which are usually welded with the apparatus. This standard describes a selection of various shapes of saddle supports and the dimensions. The apparatus manufacturer shall provide a proof of strength and stability.

Saddle supports for horizontal apparatus - Dimensions

DIN 28030-1:2003 容器和加工装置用法兰接头.第1部分:带法兰的设备用容器

This standard applies to flanged joints on multipart equipment. These specifications apply by analogy to flanged joints of differing materials and designs or intended for higher permissible operating pressures and temperatures.

Flanged joints for vessels and process apparatus - Part 1: Apparatus flanged vessels

DIN 28038:2003 不锈钢制压力容器和加工装置用带圆柱形毂焊接法兰

The project specifies the dimensions and designation for weld flanges with cylindrical hub for pressure vessels and process apparatus of stainless steel. The requirements for flanged joints are specified in DIN 28030-1, the limit deviation in DIN 38030-2.#,,#

Weld flanges with cylindrical hub for pressure vessels and process apparatus of stainless steel

DIN 28031:2003 非合金钢和不锈钢制非加压容器和加工装置用焊接法兰

The project specifies the dimensions and designation for weld flanges for unpressurized vessels and process apparatus of non-alloy and stainless steel to be used in accordance with DIN 28030-1 and DIN 28030-2. The requirements for flanged joints are specified in DIN 28030-1, the limit deviation in DIN 28030-2.#,,#

Weld flanges for unpressurized vessels and process apparatus of non-alloy and stainless steel

DIN 28030-2:2003 容器和处理设备法兰连接.第2部分;法兰尺寸公差

This standard applies to ready-made flanges; unmachined parts for the manufacture of flanges are not covered by this standard. Compliance with the limit deviations ensures the interchangeability of the flanges.

Flanged joints for vessels and process apparatus - Part 2: Tolerances on flange dimensions

DIN 28115:2003 碳钢喷嘴.PN 10 至 PN 40

Carbon steel nozzles - PN 10 to PN 40

DIN 28025:2003 不锈钢喷嘴.PN 10 至 PN 40

Nozzles of stainless steel - PN 10 to PN 40

HG/T 3139.11-2001 釜用立式减速机YP系列带传动减速机

本标准规定了YP系列大功率带传动减速机(以下简称减速机)的产品分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于石油化工、制药、轻工、冶金矿山、水处理等釜用搅拌减速机以及其他用途的立式减速机。

Vertical reducer for tank series YP belt-driving reducer

HG/T 3139.1-2001 釜用立式减速机型式和基本参数

本标准规定了釜用立式减速机(以下简称“减速机”)的种类、类型代号、型号表示方法及基本参数。 本标准适用于电动机功率范围为0．04～380kW的釜用立式减速机。 其他用途的立式减速机亦可参照采用本标准。

Vertical reducer for tank Types and paramters

HG/T 3139.2-2001 釜用立式减速机XL系列摆线针轮减速机

本标准规定了XL系列单级、两级、三级釜用立式摆线针轮减速机(以下简称减速机)的产品分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准的要求、试验方法、检验规则、标志、包装、运输、贮存也适用于BLD型摆线针轮减速机。 本标准适用于石油化工、轻工食品、制药等釜用搅拌减速机以及其他用途的立式减速机。

Vertical reducer for tank Series XL cycloidal gear reducer

HG/T 3139.3-2001 釜用立式减速机LC系列圆柱齿轮减速机

本标准规定了LC系列两级同轴式圆柱齿轮减速机(以下简称减速机)的产品分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于石油化工、冶金矿山、轻工食品、制药及污水处理等釜用搅拌减速机以及其他用途的立式减速机。

Vertical reducer for tank series LC cycloidal gears reducer