75.140 石蜡、沥青材料和其他石油产品 标准查询与下载

KS F 2360-2021 沥青集料混合料颗粒包覆度试验方法

Testing method for degree of particle coating of asphalt-aggregate mixture

PN-EN 13614-2021-08 E 沥青和沥青结合料水浸试验法测定沥青乳液的粘结性

Bitumen and bituminous binders--Determination of adhesivity of bituminous emulsions by water immersion test

BS EN 13614:2021 沥青和沥青粘合剂 水浸试验测定沥青乳液的附着力

Bitumen and bituminous binders. Determination of adhesivity of bituminous emulsions by water immersion test

GSO EN 13305:2021 沥青和沥青粘合剂 硬质工业沥青规范框架

This European Standard provides a framework for the specification of hard industrial bitumens used mainly in flooring, varnishes, mineral rubber, roofing and mastic. Within Europe several types of hard industrial bitumen are used, and dependent upon traditional practices, different grades may be used for the same purpose. The framework given in this European standard provides a basis for quality agreements to be established between supplier and client. The hard industrial bitumen products are graded by the limits of the ring and ball softening point values, expressed as multiples of 5, and are characterised by an H in front of the values.

Bitumen and bituminous binders. Framework for specification of hard industrial bitumens

OENORM EN 13614-2021 沥青和沥青粘合剂 通过水浸试验测定沥青乳液的粘附性

Bitumen and bituminous binders - Determination of adhesivity of bituminous emulsions by water immersion test

GSO ASTM D5442:2021 用气相色谱法分析石油蜡的标准试验方法

1.1 This test method covers the quantitative determination of the carbon number distribution of petroleum waxes in the range from n-C17 through n-C44 by gas chromatography using internal standardization. In addition, the content of normal and non-normal hydrocarbons for each carbon number is also determined. Material with a carbon number above n -C44 is determined by its difference from 100 % by mass and reported as C45+. 1.2 This test method is applicable to petroleum derived waxes, including blends of waxes. This test method is not applicable to oxygenated waxes, such as synthetic polyethylene glycols (for example, Carbowax2 ), or natural products such as beeswax or carnauba. 1.3 This test method is not directly applicable to waxes with oil content greater than 10 % as determined by Test Method D721. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee

Standard Test Method for Analysis of Petroleum Waxes by Gas Chromatography

GSO ASTM D1833:2021 石油蜡气味的标准测试方法

1.1 This test method covers a procedure for rating the odor intensity of waxes derived from petroleum. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Odor of Petroleum Wax

T/CSEA 16-2021 高固份型汽车防腐蜡

项    目　质量指标　试验方法 外观　米黄色到浅褐色膏状体　目测 气味  （120℃，2h）不大于　3.0（无刺激性气味）　SH/T 0414 粘度（30℃），Pa·S　0.3~3.0　GB/T 2794 密度（20℃），kg/m3 　780~1180　GB/T 13377 不挥发份（120℃，2 h），％，不小于　90　GB/T 1725 闪点（开口杯），℃，不小于　100　GB/T 3536 干膜滴点a ，℃，不小于　100　SH/T 0800 细度，μm ，不大于　50　GB/T 1724 成膜干燥性（湿膜50μm，冷轧钢板）　膜平整，表干不超过14天　GB/T 1728  耐水性 （干膜50μm，23℃±2℃，240h,电泳漆板）　无软化、膨胀、剥离等　GB/T 1733   与电泳漆附着力（干膜100μm，电泳漆板）　在划线的边缘及交叉点处允许成片的蜡膜脱落，但脱离总面积小于等于35%　GB/T 9286 接缝渗透性（25℃±2℃），mm，不小于　25　附录A 垂直流挂性（湿膜300μm，电泳漆板）　无流挂　附录B 喷雾化性能（25℃±2℃）　雾化性能良好　附录C 高温蠕变性（干膜50μm，电泳漆板80℃,24 h）,mm，不大于　2　附录D 低温延展性（干膜50μm，电泳漆板-35℃,8 h）　蜡膜无开裂、无剥离　附录E 耐加热老化性（干膜50μm，冷轧钢板）　无流挂、无腐蚀　附录F 湿热实验（干膜50μm，冷轧钢板），A级，h,不小于　1000　GB/T 2361 盐雾实验（干膜50μm，冷轧钢板），A级，h,不小于　1000　SH/T 0081 a  干膜制备：将蜡均匀涂布厚度50~100μm，室温下放置14天后干燥，进行测试。 5.2　空腔浇注防腐蜡的技术要求和试验方法见表2。 表2　空腔浇注防腐蜡的技术要求和试验方法 项    目　质量指标　试验方法 外观（室温）　白色到淡黄色固体　目测 密度（120℃±2℃），kg/m3　760~800　GB/T 13377 表2  空腔浇注防腐蜡的技术要求和试验方法（续） 项    目　质量指标　试验方法 挥发分（120℃，2h），％，不大于　0.5　GB/T 1725 运动粘度（120℃），mm2/s　5.5~7.5　GB/T 11137 滴点，℃，大于　89　SH/T 0800 凝点，℃，不小于　67　SH/T 0132 闪点（开口杯），℃，不小于　250　GB/T 3536 湿热试验（50μm，冷轧钢板），A级，h,不小于　480　GB/T 2361 盐雾试验（50μm，冷轧钢板），A级，h,不小于　240　SH/T 0081 储存稳定性（120℃±2℃，30天）　允许外观颜色变化，其余无影响　目测

High-solid car anti-corrosion wax

LST EN 13614-2021 沥青和沥青粘合剂 通过水浸试验测定沥青乳液的粘附性

Bitumen and bituminous binders - Determination of adhesivity of bituminous emulsions by water immersion test

DS/EN 13614:2021 沥青和沥青结合料 水浸试验测定沥青乳液的粘合力

Bitumen and bituminous binders – Determination of adhesivity of bituminous emulsions by water immersion test

EN 13614:2021 沥青和沥青粘合剂 通过水浸试验测定沥青乳液的粘附性

Bitumen and bituminous binders - Determination of adhesivity of bituminous emulsions by water immersion test

OENORM EN 17643-2021 沥青和沥青粘合剂 使用动态剪切流变仪（DSR）测定等剪切模量温度 BTSV 测试

Bitumen and bituminous binders - Determination of equi-shear modulus temperature using a Dynamic Shear Rheometer (DSR) - BTSV test

OENORM EN 12847-2021 沥青和沥青粘合剂 沥青乳液沉降趋势的测定

Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions

ASTM D850-21 工业芳烃和相关材料蒸馏的标准试验方法

1.1?This test method covers the distillation of industrial aromatic hydrocarbons and related materials of relatively narrow boiling ranges from 30 to 250��C. Warning—This test method is not applicable for styrene which will exothermically polymerize during the distillation proce

Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials

NF P98-818-42:2021 沥青混合料 试验方法 第42部分：再生沥青中的异物含量

Bituminous mixtures - Test methods - Part 42 : amount of foreign matter in reclaimed asphalt

ASTM D1465-10(2021) 石油蜡封堵点标准试验方法

1.1 This test method covers the determination of the blocking point and picking point of petroleum wax. 1.2 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Blocking and Picking Points of Petroleum Wax

ASTM D4419-90(2021) 通过差示扫描量热法测定石油蜡的转变温度的标准试验方法（DSC）

1.1 This test method covers the transition temperatures of petroleum waxes, including microcrystalline waxes, by differential scanning calorimetry (DSC). These transitions may occur as a solid-solid transition or as a solid-liquid transition. 1.2 The normal operating temperature range extends from 15 °C to 150 °C (Note 1). 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Transition Temperatures of Petroleum Waxes by Differential Scanning Calorimetry (DSC)

ASTM D4798/D4798M-11(2021) 沥青材料加速老化试验条件和程序的标准做法（氙弧法）

1.1 This practice covers test conditions and procedures for xenon-arc exposures according to Practices G151 and G155 for bituminous roofing and waterproofing materials. (See Terminology G113.) 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)

prEN 17643-2021 沥青和沥青粘合剂 使用动态剪切流变仪（DSR）测定等剪切模量温度 BTSV 测试

Bitumen and bituminous binders - Determination of equi-shear modulus temperature using a Dynamic Shear Rheometer (DSR) - BTSV test

GOST 23683-2021 固体石油石蜡 技术条件

Petroleum paraffin waxes. Specifications