75.140 (Waxes, bituminous materials and other petr 标准查询与下载

ASTM D6752-02a 用自动真空密封法测量压紧的沥青混合料的堆积比重和密度的标准试验方法

1.1 This test method covers the determination of bulk specific gravity of compacted bituminous mixtures by the vacuum sealing method.1.2 This method can be used for compacted cylindrical and cubical bituminous laboratory and field specimens.1.3 The bulk specific gravity of the compacted bituminous mixtures may be used in calculating the unit weight of the mixture.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method

ASTM D4798-01 沥青材料加速老化试验条件和程序的标准试验方法(氙弧法)

1.1 This test method covers test conditions and procedures for xenon-arc exposures according to Practice G151 and G155 for bituminous roofing and waterproofing materials having a minimum softening point of approximately 95176C (200176F) as determined by Test Method D36.(Also see Terminology G113.) 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)

ASTM D6627-01(2006) 冷沥青混合料挥发性馏份测定的标准试验方法

This test method is used for determining the amount of a temperature specific volatile distillate fraction in cold mix asphalt mixtures.1.1 This test method covers the determination, by direct measurement, of the ambient to 500176;F (260176;C) volatile distillate fraction of cold mix asphalt mixtures.1.2 A precision and bias statement for the Standard has not been developed since this test method is used for research purposes or information only. Therefore this Standard should not be used for acceptance or rejection of a material for purchasing purposes.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of a Volatile Distillate Fraction of Cold Asphalt Mixtures

ASTM D6627-01 冷沥青混合料挥发性馏份测定的标准试验方法

1.1 This test method covers the determination, by direct measurement, of the ambient to 500oF (260oC) volatile distillate fraction of cold mix asphalt mixtures.1.2 A precision and bias statement for the Standard has not been developed since this test method is used for research purposes or information only. Therefore this Standard should not be used for acceptance or rejection of a material for purchasing purposes.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of a Volatile Distillate Fraction of Cold Asphalt Mixtures

ASTM D6140-00(2009) 测定全幅沥青铺面用铺设物中沥青滞留的标准试验方法

The asphalt retention is a test procedure for full-width paving fabrics. The use of this test method is to establish an index value by providing standard criteria and a basis for uniform reporting. This procedure is applicable for testing conditioned specimens (see 8.1). The results obtained may vary, depending on which type of asphalt cement is used for the test. Unless stated otherwise, use A.C. 20 as defined in Specification D3381 or equivalent asphalt cement. This procedure is applicable whenever it is desired to determine an index asphalt retention of paving fabric. If it becomes necessary for the purchaser and the seller to use this test method for acceptance testing, the statistical bias, if any, between the purchaser''s and seller''s laboratories should be determined. Such comparison is to be based on specimens randomly drawn from the sample of geotextile being evaluated.1.1 This test method covers a procedure for determining the asphalt retention for paving fabrics. Paving fabrics are used in a fabric membrane interlayer system in pavements before the placement of an asphaltic overlay. 1.2 This test method shows the values in both SI units and inch-pound units. SI Units is the name for the system of metric units known as the International System of Units. Inch-pound units is the correct name for the customary units used in the United States. The values in inch-pound units are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method to Determine Asphalt Retention of Paving Fabrics Used in Asphalt Paving for Full-Width Applications

ASTM D5361-00 实验室试验用压实沥青混合料取样的标准操作规程

1.1 This practice describes a procedure for removal of a sample of compacted bituminous mixture from a pavement for laboratory testing. 1.2 The values given in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Sampling Compacted Bituminous Mixtures for Laboratory Testing

ASTM D4799-00 沥青材料加速老化的标准试验方法(萤光UV和冷凝法)

1.1 This test method covers the test conditions and procedures that are applicable when Practice G53 is employed for the exposure of bituminous roofing and waterproofing materials having a minimum softening point of approximately 200176F (95176C) as determined by Test Method D36. 1.2 The values stated in inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV and Condensation Method)

ASTM D4798-00 沥青材料加速老化试验条件和程序的标准试验方法(氙弧法)

1.1 This test method covers test conditions and procedures for xenon-arc exposures according to Practice G151 and G155 for bituminous roofing and waterproofing materials having a minimum softening point of approximately 95176C (200176F) as determined by Test Method D36.(Also see Terminology G113.) 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)

ASTM D95-99e1 蒸馏法测定石油产品和沥青材料中水含量的试验方法

1.1 This test method covers the determination of water in the range from 0 to 25 % volume in petroleum products, tars, and other bituminous materials by the distillation method. Note 18212;Volatile water-soluble material, if present, may be measured as water.1.2 The specific products considered during the development of this test method are listed in Table 1. For bituminous emulsions refer to Test Method D 244. For crude oils, refer to Test Method D 4006 (API MPMS Chapter 10.2).Note 28212;With some types of oil, satisfactory results may be obtained from Test Method D 1796 (API MPMS Chapter 10.6).1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.

Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

ASTM D4072-98(2003)e1 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

This test method is useful for evaluating and characterizing tars and pitches and as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D1386-98 合成蜡和天然蜡的酸值(以实验为基础的)的试验方法

1.1 This test method covers the determination of the acid number of synthetic waxes and natural waxes. The number is obtained by direct titration of the material and indicates the amount of free acid present. 1.2 This test method, using an ethanol-xylene mixture, is applicable to all natural waxes, including carnauba. The test method is also applicable to oxidized microcrystalline waxes, oxidized Fischer-Tropsch, oxidized polyethylene, and montan esters. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. >

Standard Test Method for Acid Number (Empirical) of Synthetic and Natural Waxes

ASTM D2320-98 固态沥青比重(表面引力)的标准试验方法(比重瓶法)

1.1 This test method covers the determination of density and relative density by pycnometer, and can be used for pitch that can be handled in fragments. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method)

ASTM D2415-98 测试煤焦油和硬沥青中灰分的标准试验方法

1.1 This test method covers the determination of the ash content of tar and pitch.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ash in Coal Tar and Pitch

ASTM D4072-98 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D2319-98 硬沥青软化点的标准试验方法(空气中立方块试验法)

1.1 This test method covers the determination of the softening point above 176176F (80176C) of pitch. Test Method D 3104 gives comparable results. 1.2 The values stated in inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Softening Point of Pitch (Cube-in-Air Method)

ASTM D2320-98(2003) 固态沥青比重(表面引力)的标准试验方法(比重瓶法)

Values of density and relative density are used for converting volumes to units of mass as required in other ASTM standards and in sales transactions.1.1 This test method covers the determination of density and relative density by pycnometer, and can be used for pitch that can be handled in fragments.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method)

ASTM D2318-98(2008) 焦油和硬沥青中喹啉不溶物(QI)含量的标准试验方法

This test method is useful in evaluating and characterizing tar and pitch, and as one element in establishing the uniformity of shipments and sources of supply.1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazards information, see Section 7.

Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch

ASTM D2415-98(2008) 煤焦油和沥青中灰份含量的标准试验方法

This test method determines the amount of inorganic matter in the sample.1.1 This test method covers the determination of the ash content of tar and pitch. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ash in Coal Tar and Pitch

ASTM D4072-98(2008) 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

This test method is useful for evaluating and characterizing tars and pitches and as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D4715-98(2008)e1 测定焦油和硬沥青焦化值的试验方法(Alcan)

This test method is useful for indicating the relative coke-forming propensities and for evaluating and characterizing tars and pitches. The test method can also be used as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5 %, as determined by Test Method D 2415. 1.2 Coking values by this test method are higher than those obtained by Test Method D 2416. See the bias statement in Section 13. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)