75.160.01 燃料综合 标准查询与下载

GB/T 19952-2005 煤炭在线分析仪测量性能评价方法

本标准规定了对煤炭在线分析仪（也简称分析仪）测量性能进行评价的程序、适用的试验方法和试验数据的统计判断技术。 本标准适用于各种类型的煤炭在线分析仪。

Evaluation of the measurement performance of on-line analysers for coal

DB3705/T 24-2023 成品油质量追溯体系建设规范

Specification for the construction of refined oil quality traceability system

T/DYZL 030-2023 东营市成品油质量可追溯体系

主要内容为取样留样、油品检验、数据采集、质量信息传递、质量追溯、质量对比、监督检查、品牌建设等

Traciblity control system for refined oil quality of DongYing city

T/CIET 033-2023 电动轮椅用永磁直流有刷减速电动机

本文件规定电动轮椅用永磁直流减速电动机的术语和定义，型式、基本参数，基本要求，技术要求，试验方法，检验规则，铭牌、包装、贮存及运输，和质量承诺。 本文件适用于电动轮椅用永磁直流有刷减速电动机(以下简称电动机)，不适用于无刷直流电动机以及直驱型电动机。

Permanent Magnet DC Brushed Geared Motor for Electric Wheelchair

ASTM D6824-23 测定航空涡轮燃料可过滤性的标准试验方法

1.1 This test method covers a procedure for determining the filterability of aviation turbine fuels (for other middle distillate fuels, see Test Method D6426). NOTE 1—ASTM specification fuels falling within the scope of this test method are Specifications D1655 and D6615 and the military fuels covered in the military specifications listed in 2.2. 1.2 This test method is not applicable to fuels that contain undissolved water. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Filterability of Aviation Turbine Fuel

T/DYZL 030-2022 东营市成品油质量可追溯体系

主要内容为取样留样、油品检验、数据采集、质量信息传递、质量追溯、质量对比、监督检查、品牌建设等

Traciblity control system for refined oil quality of DongYing city

T/SDHCIA 020-2022 锅炉用醇基燃料

本文件规定了锅炉用醇基燃料的技术要求、试验方法、检验规则、标志、包装、运输、贮存及安全。 本文件适用于以己内酰胺、己二酸生产工艺中副产的醇醚混合物等为主要原料，经精馏、调制生产的锅炉用醇基燃料，供工业燃油锅炉使用。

Alcohol-based fuel for boilers

NB/T 10770-2021 生物重油

本文件规定了生物重油的技术要求和试验方法，检验规则，标志、包装、运输和贮存等。 本文件适用于生物柴油企业生产的生物重油，符合本文件的产品可用于生产铸造粘结剂、橡胶软化剂、沥青、涂料、选矿悬浮剂、化肥防结块剂、皮革助剂及锅炉燃料等。

bioheavy oil

T/DYZL 004-2021 成品油质量全链条可追溯管控体系

本文件代替T/DYZL 004-2018《成品油质量全链条可追溯管控体系》，与T/DYZL 004-2018相比主要 技术变化如下： ——删除了第3章规范性引用文件中的第一段“GB 252《普通柴油》”； ——删除了4.6中的“普通柴油分析按照GB 252执行”； ——删除了第1章第二段“本体系以团体标准形式发布，鼓励辖区内各相关企业自愿采用。相关监 督管理部门将采取适当形式鼓励引导企业采用本标准或高于本标准的其他标准，并对企业的实施情况进 行监督检查”； ——将文件英文名称修改为“Whole chain of traciblity control system for refined oil  quality”； ——将第1章题目“适用范围”修改为“范围”； ——将第1章适用范围中的第一段由原来“本文件适用于以炼化企业为源头的生产企业质量管控、 运输车辆质量管控”修订为“本文件规定了以炼化企业为源头的生产企业产品质量管控、出厂环节质量 管控、车辆运输过程质量管控”； ——将第2章规范性引用文件的第五段修改为NB/SH/T 0164《石油产品包装、贮运及交货验收规则》； ——增加第3章 术语和定义 ； ——将4.3中“容器必须保持清洁、干燥并且为专用棕色”，修改为“容器必须保持清洁、干燥”； 本文件由东营质量协会发布。 本文件起草单位：富海集团新能源控股有限公司、东营华联石油化工厂有限公司、东营联合石化有 限责任公司、山东万通石油化工集团有限公司、山东垦利石化集团有限公司、山东神驰化工集团有限公 司、齐成（山东）石化集团有限公司、东营市科普服务中心。 本文件主要起草人：马军芳、韩志峰、姚爱海、孙志会、王翠英、陈新建、崔洪凯、于霞、乔红霞、 王学峰、孙正义、宗学花、李明、刘彩莲、孙海玻、徐跃飞、秦文洁、刘华玲、张艳敏、鞠云忠、张兴 波、魏丹、刘帅帅、聂岗、郑健。 本文件及其所代替文件发布情况为： ——2018年首次发布为T/DYZL 004-2018； ——本次为第一次修订

Whole chain of traciblity control system for refined oil quality

T/XXRL 07-2021 高清洁燃料组分油

术语和定义 原料要求 技术要求 检验规则 标志、包装、运输和贮存 安全

High Clean Fuel Component Oil

T/JTAIT 7-2021 柴油发动机氮氧化物还原剂-尿素水溶液（AUS 32）快速筛查技术规范

本文件规定了柴油发动机氮氧化物还原剂-尿素水溶液（AUS 32）的快速筛查阈值、取样、快速筛查方法、快速筛查方法验证、移动设施、结果处理和报告。  本文件适用于柴油发动机氮氧化物还原剂-尿素水溶液（AUS 32）的快速筛查。

Technical Specifications for Quick Screening of Diesel Engine Nitrogen Oxide Reducing Agent-Urea Aqueous Solution (AUS 32)

DB34/T 3786-2021 固体生物质燃料分类

Classification of solid biomass fuels

T/CNCA 003-2020 煤直接液化柴油

本文件规定了煤直接液化柴油的术语和定义、产品分类、技术要求和试验方法、取样、检验规则、标志、包装、运输和贮存、安全

Coal direct liquefied diesel

ASTM D5504-20 通过气相色谱和化学发光测定天然气和气态燃料中硫化合物的标准测试方法

1.1 This test method is primarily for the determination of speciated volatile sulfur-containing compounds in high methane content gaseous fuels such as natural gas. It has been successfully applied to other types of gaseous samples, including air, digester, landfill, and refinery fuel gas. The detection range for sulfur compounds, reported as picograms sulfur, is 0.01 to 1000. This is equivalent to 0.01 to 1000 mg/m3 , based upon the analysis of a 1 cc sample. 1.2 The range of this test method may be extended to higher concentration by dilution or by selection of a smaller sample loop. NOTE 1— Dilution will reduce method precision. 1.3 This test method does not purport to identify all sulfur species in a sample. Only compounds that are eluted through the selected column under the chromatographic conditions chosen are determined. The detector response to sulfur is equimolar for all sulfur compounds within the scope (1.1) of this test method. Thus, unidentified compounds are determined with equal precision to that of identified substances. Total sulfur content is determined from the total of individually quantified components. 1.4 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence

ASTM D8322-20 用微波等离子体原子发射光谱法（MP-AES）测定残余燃料和原油中元素的标准试验方法

1.1 This test method covers the determination of metals and other elements in residual fuel and crude oil by microwave plasma atomic emission spectroscopy (MP-AES). The specific elements within the scope of this method are V, Ni, Ca, Na, Al, Si, Zn, P, and S for residual fuel oil and Fe, V, Ni, Ca, Na, K, and S for crude oils. 1.2 Method working range: high expected concentration limit = highest ILS sample mean low expected concentration limit = lowest ILS sample mean if: (1) lowest ILS sample mean − Rlowest ILS sample mean > 0; otherwise it is determined by solving for X using the following equation: (2) X − RX= coarsest resolution, determined by 0.5*σr lowest ILS sample mean Crude Oil: Element Method Working Range (expected mg/kg) Iron 0.70 to 161.02 Vanadium 2.88 to 417.50 Nickel 0.36 to 107.66 Calcium 5.41 to 96.78 Sodium 1.18 to 97.13 Potassium 7.01 to 63.83 Sulfur 1059 to 35194 Residual Fuel Oil: Element Method Working Range (expected mg/kg) Vanadium 3.88 to 370.09 Nickel 1.47 to 96.68 Calcium 4.41 to 102.01 Sodium 2.80 to 112.67 Aluminum 4.13 to 154.12 Silicon 5.99 to 237.56 Zinc 2.75 to 102.46 Sulfur 1314 to 30134 1.3 This test method uses soluble metals in organic solvents for calibration and does not purport to quantitatively determine insoluble particulates. Analytical results are particle size dependent, and particles larger than a few micrometers may cause results to appear low 1.4 Elements present at mass fractions above the upper limit of the calibration curves can be determined with additional appropriate dilutions. Elements shall be measured at the wavelengths presented in Table 1. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Elements in Residual Fuels and Crude Oils by Microwave Plasma Atomic Emission Spectroscopy (MP-AES)

T/DYZL 012-2019 成品油生产发售和终端零售服务规范

本标准规定了成品油生产发售、终端零售服务的相关服务设计、服务规范、安全与应急管理、服务投诉与处理等内容。 本服务标准适用于以炼化企业为源头的生产发售一体化企业，涉及成品油生产发售与终端零售环节的服务标准，部分企业缺少其中个别环节可不执行缺少部分的相关规定。

Specifications for refined oil production, sales and terminal retail services

ASTM D6824-13(2018) 确定航空涡轮燃料过滤能力的标准试验方法

1.1 This test method covers a procedure for determining the filterability of aviation turbine fuels (for other middle distillate fuels, see Test Method D6426). NOTE 1—ASTM specification fuels falling within the scope of this test method are Specifications D1655 and D6615 and the military fuels covered in the military specifications listed in 2.2. 1.2 This test method is not applicable to fuels that contain undissolved water. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Filterability of Aviation Turbine Fuel

DB34/T 3069-2017 固体生物质燃料中碳氢的测定方法-电量重量法

本标准规定了用电量法测定固体生物质燃料中氢、用重量法测定固体生物质燃料中碳的方法原理、 试剂和材料、仪器设备、测定准备、试验步骤、结果计算及精密度等。 本标准适用于各种固体生物质燃料中碳氢的测定

Method for Determination of Hydrocarbons in Solid Biomass Fuels-Electrogravimetric Method

T/AHJC 0004-2017 醇基清洁燃料行业安全操作规范

本标准的醇基清洁燃料是指以醇类为基础配制成的拥有15%以上内含氧的醇基清洁燃料，适于用作民用炊事燃料、锅炉燃料和工业窑炉燃料

Safe Operation Specification Of Alcohol-based Clean Fuel Industry

SN/T 4939-2017 进出口岸罐贮存石油及石油产品检验规程

Inspection regulations for petroleum and petroleum products stored in import and port tanks