75.160.10 固体燃料 标准查询与下载

T/CASME 21-2022 工业锅炉用生物质成型燃料

本文件规定了工业锅炉用生物质成型燃料的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Biomass briquette fuel for industrial boiler

T/CPCIF 0226-2022 工业用回转热解提质焦粉

项  目　符号　技  术  要  求　试验方法 　　一  级　二  级　三  级　 全水分，w/%　Mt　≤8.00　≤12.00　≤15.00　GB/T 211 灰分，w/%　Ad　≤8.00　≤12.00　≤15.00　GB/T 212a或GB/T 30732 挥发分，w/%　Vdaf　≤12.00　≤14.00　≤15.00　GB/T 212b或GB/T 30732 固定碳，w/%　FCd　≥82.00　≥80.00　≥78.00　GB/T 212b或GB/T 30732 全硫，w/%　St,d　≤0.30　≤0.50　≤1.00　GB/T 214c或GB/T 25214 发热量/（MJ/kg）　Qnet,ar　≥28.00　≥25.00　≥21.00　GB/T 213 哈氏可磨指数　HGI　≥60　≥50　—　GB/T 2565 反应性（1100 ℃），w%　α　≥95　GB/T 220 热稳定性，w/%　TS+6　≥80　≥70　≥60　GB/T 1573 氧化铝，w/%　w(Al2O3)　≤2.00　≤4.00　—　GB/T 1574 磷，w/%　Pd　≤0.01　≤0.05　—　GB/T 216 钾和钠总量，w/%　w(K＋Na)　≤0.12　≤0.20　—　GB/T 1574 a  以GB/T 212中的仲裁法为准。 b  以GB/T 212方法为准。 c  以GB/T 214方法为准。

Rotary pyrolysis upgraded coke breeze for industrial use

ASTM D3302/D3302M-22 煤中总水分的标准试验方法

1.1 This test method covers the measurement of the total moisture in coal as it exists at the site, at the time, and under the conditions it is sampled. It is applicable to coals as mined, processed, shipped, or used in normal commercial pursuits. It is not applicable to coal-water slurries, sludges, or pulverized products under 0.5 mm-diameter sieve size. It is applicable to coals of all ranks within the recognized limitations imposed by oxidation and decomposition characteristics of lower rank coals. Because of its empirical nature, strict adherence to basic principles and permissive procedures are required for valid results (see Appendix X1). This complete standard is available to producers, sellers, and consumers as a total moisture method when other procedures or modifications are not mutually agreed on. 1.2 Since coal can vary from extremely wet (watersaturated) to completely dry, special emphasis must be placed on the sampling, sample preparation, and the moisture determination itself to ensure total reliability of measurement. Therefore, this standard entails collection of the gross sample, sample preparation, and the method of determination. 1.3 While it is recognized that such a standard may be unwieldy for routine usage in commercial operations, it can provide a common base for agreement in cases of dispute or arbitration. The complete standard is referred to as the referee method. Embodied in the standard is the commercial method starting with the crushed and divided sample when the gross sample is not too wet to crush and divide. See Practice D2961/D2961M and Test Method D3173 for other moisture methods. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Total Moisture in Coal

DB13/T 5622-2022 固体生物质燃料中氟含量的测定 氧弹燃烧-离子选择电极法

Determination of Fluorine Content in Solid Biomass Fuel Oxygen Bomb Combustion-Ion Selective Electrode Method

CEN ISO/TS 21911-2:2022 固体回收燃料 自热的测定 第2部分：篮式加热试验（ISO/TS 21911-2:2022）

This document gives guidance on basket heating tests for characterization of self-heating properties of solid recovered fuels (SRFs). This document includes: a) a compilation of basket heating test methods; b) guidance on the applicability and use of basket heating tests for SRF; c) information on the application of basket heating test data for calculations of critical conditions in storage. Data on spontaneous heat generation determined using this document is only associated with the specific quality and age of the sample material. The information derived using this document is intended for use in quality control and in hazard and risk assessments related to the procedures given in ISO 21912.

Solid recovered fuels - Determination of self-heating - Part 2: Basket heating tests (ISO/TS 21911-2:2022)

ISO/TS 21911-2:2022 固体回收燃料.自热测定.第2部分:篮式加热试验

Solid recovered fuels — Determination of self-heating — Part 2: Basket heating tests

EN ISO 21646:2022 固体回收燃料.样品制备

This document specifies methods for sample preparation to ensure representativeness of the samples throughout the preparation procedures to produce general analysis samples. Suitable test portions can be taken from the laboratory or general analysis samples and used for analysis according to the specific requirements defined in the corresponding analytical procedures. This document specifies the correct sample preparation sequence to be applied to: a) the composite sample, in order to produce a laboratory sample (taking into account large pieces of solid recovered fuel); b) each sub-sampling step throughout the testing programme; c) the laboratory sample, in order to obtain suitable test portions; d) ensure the representativeness of the test portions that have been taken according to the sample preparation plan, prior to physical analysis, chemical analysis or both (e.g. extractions, digestion, analytical determinations). The methods specified in this document can be used for sample preparation, for example, when the samples are to be tested for bulk density, biomass content determination, mechanical durability, particle size distribution, moisture content, ash content, ash melting behaviour, calorific value, chemical composition, impurities and self-heating properties. The methods are not intended to be applied to the very large samples required for the testing of bridging properties.

Solid recovered fuels - Sample preparation (ISO 21646:2022)

ISO 21646:2022 固体回收燃料.样品制备

This document specifies methods for sample preparation to ensure representativeness of the samples throughout the preparation procedures to produce general analysis samples. Suitable test portions can be taken from the laboratory or general analysis samples and used for analysis according to the specific requirements defined in the corresponding analytical procedures. This document specifies the correct sample preparation sequence to be applied to: a) the composite sample, in order to produce a laboratory sample (taking into account large pieces of solid recovered fuel); b) each sub-sampling step throughout the testing programme; c) the laboratory sample, in order to obtain suitable test portions; d) ensure the representativeness of the test portions that have been taken according to the sample preparation plan, prior to physical analysis, chemical analysis or both (e.g. extractions, digestion, analytical determinations). The methods specified in this document can be used for sample preparation, for example, when the samples are to be tested for bulk density, biomass content determination, mechanical durability, particle size distribution, moisture content, ash content, ash melting behaviour, calorific value, chemical composition, impurities and self-heating properties. The methods are not intended to be applied to the very large samples required for the testing of bridging properties.

Solid recovered fuels — Sample preparation

ASTM D5709-22 石油焦筛分分析的标准试验方法

1.1 This test method details a procedure for performing particle size distribution analysis by dry sieve testing on green petroleum coke with a topsize of no more than 75 mm and calcined petroleum coke with a topsize of no more than 25 mm. Size fractions go down to and include 4.75 mm for green petroleum coke and 75 µm for calcined petroleum coke. NOTE 1—To convert units, see Table 1 on nominal dimensions in Specification E11. For example, 75 mm is approximately equivalent to a nominal sieve opening of 3 in. and 25 mm to a nominal sieve opening of 1 in. Likewise, 4.75 mm can be converted to approximately 0.187 in. and 75 microns to 0.0029 in. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 The sieve size is reported as U.S.A. standard test series in any units listed in Table 1 on nominal dimensions of Specification E11, or their commercial size equivalents. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Sieve Analysis of Petroleum Coke

ASTM D2944-22 园艺用加工泥炭材料取样的标准实施规程

1.1 This practice covers the procedure for obtaining a representative sample of processed peat material from compressed bales or bulk loose material sources. This procedure is applicable for sampling peat materials for horticultural purposes and produces a sample that is representative of peat materials that may be heterogeneous in nature. Producing a representative sample of a material is central to the validity of the results for any testing or analytical procedure which can be used to verify the grade of peat. 1.2 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only and are not considered standard. 1.3 All observed and calculated values shall confirm to the guidelines for significant digits and rounding established in Practice D6026. 1.3.1 The procedures used to specify how data are collected/ recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word ”Standard” in the title of this document means only that the document has been approved though the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice of Sampling Processed Peat Materials for Horticultural Purposes

ASTM E791-08(2022) 根据测定的不同基准计算垃圾衍生燃料分析数据的标准试验方法

1.1 This test method gives equations to enable analytical data from the application of RDF analysis procedures to be expressed on various different bases in common use. Such bases are: as-received; dry; dry, ash-free; and others. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Calculating Refuse-Derived Fuel Analysis Data from As-Determined to Different Bases

22/30354909 DC BS EN ISO 21911-1 固体回收燃料 自热测定 第 1 部分：等温量热法

BS EN ISO 21911-1. Solid recovered fuels. Determination of self-heating - Part 1. Isothermal calorimetry

T/CCIAA 10-2021 焦炉焦饼中心温度测定技术规范

本文件规定了焦炉焦饼中心温度测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven coke cake central temperature determination

T/CCIAA 16-2021 焦炉炭化室墙面温度测定技术规范

本文件规定了焦炉炭化室墙面温度测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven coking chamber surface temperature determination

T/CCIAA 12-2021 焦炉冷却温度测定技术规范

本文件规定了焦炉冷却温度测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven cooling temperature determination

T/CCIAA 15-2021 焦炉炉顶表面温度测定技术规范

本文件规定了焦炉炉顶表面温度测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven roof surface temperature determination

T/CCIAA 7-2021 焦炉横排温度测定技术规范

本文件规定了焦炉横排温度测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven row temperature determination

T/CCIAA 17-2021 焦炉横管压力测定技术规范

本文件规定了焦炉横管压力测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven cross pipe pressure determination

T/CCIAA 13-2021 焦炉相邻火道温度差测定技术规范

本文件规定了焦炉相邻火道温度差测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven adjacent flue temperature difference determination

T/CCIAA 19-2021 焦炉小烟道压力测定技术规范

本文件规定了焦炉小烟道压力测定技术规范。 本文件适用于顶装焦炉和捣固焦炉。

Technical code for coke oven sole flue pressure determination