共找到 153 条与 石油和天然气工业设备 相关的标准,共 11 页
Calcuation of the thermal efficiency for petrochemical tubular heaters
Fired heaters for general refinery service
1.1 本通则适用于抗震设防烈度为 6 度~9 度地区、公称压力小于或等于 42MPa 的石油化工非埋地管 道的抗震设计。 注: 本規范一般略去“抗震設防烈度” 字樣,如 “抗震設防烈度为6 度、7 度、8 度、9 度”,简称为“6 度、7 度、 8. 9 BE”. 1.2 本通则不适用于长输管道的抗震设计。
General seismic design rule of non-buried pipe for petrochemical industry
이 규격은 수중 해리 정수가 10-9보다 큰 산/염기 성분을 함유한 석유 제품과 윤활유
Petroleum products and lubricants-Determination of acid or base number-Colour-indicator titration method
Recommended practice for evaluation of corroded pipelines
Technical Code for Construction of Centrifugal Compressor Unit for Ethylene Plant
本标准规定了油气管道钢制对焊管件的设计及选用验算的要求和方法。管件设计计算时,只考虑设计压力的作用。当必须考虑其他载荷(如热膨胀推力、弯曲力矩等)时,应另行分析,不属于本标准的范围。 本标准适用于下列条件的陆上油、气输送管道工程中的钢制对焊管件(管封头、异径接头、弯头、弯管和三通); 设计压力 p不大于10MPa; 公称直径DN不大于1000mm; 设计温度T高于-40℃,且不高于120℃;
Specification for design of steel buttwelding fittings for oil & gas pipeline
本标准适用于原油处理容器、热交换器或工艺容器与水接触面的阴极保护系统。
Technical specification of internal cathodic protection systems in oil - Treating vessels
Explosion-proof low-energy γ-γ combined logging tool
本标准规定了石油炼制用热壁加氢反应器的制造技术要求、试验方法、检验规则及标志、包装、运输等内容。 本标准适用于2(1/4)Cr-1Mo钢为主体材料、锻焊结构构的热壁加氢反应器。高于本标准及特殊的要求,应在图样或有关文件中规定。
Technical condition of forge welding hot-wall hydrogenation reactor
Evaluation procedure for defoamers used in drilling fluids
本标准规定了离心式压缩机及辅助设备的设计与制造技术要求、试验方法和检验规则,以及包装、运输等内容。 本标准适用于输送空气或其它气体的离心式压缩机。 本标准不适用于气体升压值低于34kPa的通风机和鼓风机,也不适用于JB 4113标准所指的一般炼油厂仪表空气用整体齿轮增速组装型离心式压缩机。 卖方可提供变通设计(参阅7.1.1.13说明差异的清单)。 经买卖双方同意后,也可采用相当的英制尺寸、紧固件和法兰。 本标准与订货合同相抵触时,抵触部分应以订货合同的规定为准。
Specifications for Centrifugal Compressors Used in Oil Refining and Chemical Industry
Tire type wood loading and cutting machine
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号