75.180.20 加工设备 标准查询与下载

ISO 18796-1:2018 石油、石化和天然气工业.碳钢工艺容器的内涂层和内衬.第1部分：技术要求

This document specifies the minimum technical requirements for surface preparation, materials, application, inspection and testing of internal coating and lining systems that are intended to be applied on internal surfaces of process vessels that are subject to marked pressure/temperature changes and/ or potentially corrosive conditions or processes and aggressive chemicals, used in the oil and gas industry. This document covers both new construction and maintenance works of process vessels as well as the repair of defective and deteriorated coating and lining systems. This document also provides the minimum requirements for the coated and lined samples and the criteria for their approval.

Petroleum, petrochemicals and natural gas industries - Internal coating and lining of carbon steel process vessels - Part 1: Technical requirements

GOST R 58095.0-2018 气体分配系统. 对天然气消费网络的要求. 第零部分. 概述

Gas distribution systems. Requirements for gas consumption networks. Part 0. General

ASTM D7344-17a 常压下石油产品和液体燃料蒸馏的标准试验方法（小型方法）

1.1 This test method covers the procedure for the determination of the distillation characteristics of petroleum products and liquid fuels in the range of 20 °C to 400 °C (68 °F to 752 °F) using miniaturized automatic distillation apparatus. 1.2 This test method is applicable to such products as: light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 10 % ethanol, aviation gasolines, aviation turbine fuels, all grades of No. 1 and No. 2 diesel fuels (as described in Specification D975), biodiesel (B100), biodiesel blends up to 30 % biodiesel, special petroleum spirits, pure petrochemical compounds, naphthas, white spirits, kerosenes, furnace fuel oils, and distillate marine fuels. NOTE 1—The up to 10 % by volume ethanol limit in spark ignition engine fuels (E10) was the range used in the supporting interlaboratory studies. Spark ignition engine fuels containing > 10 % by volume ethanol and up to 20 % by volume ethanol (E20) may be analyzed, however the stated precision and bias does not apply. 1.3 This test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method)

BS EN ISO 24817:2017 石油,石化和天然气工业.管道综合修理.资格认定,设计,安装,测试和检验

Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection

EN ISO 24817:2017 石油,石化和天然气工业复合材料修理管道的资格,设计,安装,测试和检验

Petroleum@ petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design@ installation@ testing and inspection

ISO 24817:2017 石油 石化和天然气工业 - 复合材料维修用于管道 - 资格和设计 安装 测试和检验

This document gives requirements and recommendations for the qualification and design, installation, testing and inspection for the external application of composite repair systems to corroded or damaged pipework, pipelines, tanks and vessels used in the petroleum, petrochemical and natural gas industries.

Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection

ASTM D7344-17 常压下石油产品和液体燃料蒸馏的标准试验方法（小型方法）

1.1 This test method covers the procedure for the determination of the distillation characteristics of petroleum products and liquid fuels in the range of 20 °C to 400 °C (68 °F to 752 °F) using miniaturized automatic distillation apparatus. 1.2 This test method is applicable to such products as: light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 10 % ethanol, aviation gasolines, aviation turbine fuels, all grades of No. 1 and No. 2 diesel fuels (as described in Specification D975), biodiesel (B100), biodiesel blends up to 30 % biodiesel, special petroleum spirits, pure petrochemical compounds, naphthas, white spirits, kerosenes, furnace fuel oils, and distillate marine fuels. NOTE 1—The up to 10 % by volume ethanol limit in spark ignition engine fuels (E10) was the range used in the supporting interlaboratory studies. Spark ignition engine fuels containing > 10 % by volume ethanol and up to 20 % by volume ethanol (E20) may be analyzed, however the stated precision and bias does not apply. 1.3 This test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method)

ASTM D7345-17 石油产品和液体燃料在大气压下蒸馏的标准试验方法（微量蒸馏法）

1.1 This test method covers a procedure for determination of the distillation characteristics of petroleum products and liquid fuels having boiling range between 20 °C to 400 °C at atmospheric pressure using an automatic micro distillation apparatus. 1.2 This test method is applicable to such products as; light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 20 % ethanol, aviation gasolines, aviation turbine fuels, regular and low sulfur diesel fuels, biodiesel (B100), biodiesel blends up to 20 % biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels, and marine fuels. 1.3 The test method is also applicable to hydrocarbons with a narrow boiling range, like organic solvents or oxygenated compounds. 1.4 The test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Micro Distillation Method)

ASTM D7345-16 石油产品和液体燃料常压蒸馏的标准试验方法 (微蒸馏法)

5.1 The distillation (volatility) characteristics of hydrocarbons and other liquids have an important effect on their safety and performance, especially in the case of fuels and solvents. The boiling range gives information on the composition, the properties, and the behavior of the fuel during storage and use. Volatility is the major determinant of the tendency of a hydrocarbon mixture to produce potentially explosive vapors. 5.2 The distillation characteristics are critically important for both automotive and aviation gasolines, affecting starting, warm-up, and tendency to vapor lock at high operating temperature or at high altitude, or both. The presence of high boiling point components in these and other fuels can significantly affect the degree of formation of solid combustion deposits. 5.3 Distillation limits are often included in petroleum product specifications, in commercial contract agreements, process refinery/control applications, and for compliance to regulatory rules. 5.4 This test method can be applied to contaminated products or hydrocarbon mixtures. This is valuable for fast product quality screening, refining process monitoring, fuel adulteration control, or other purposes including use as a portable apparatus for field testing. 5.5 This test method uses an automatic micro distillation apparatus, provides fast results using small sample volume, and eliminates much of the operator time and subjectivity in comparison to Test Method D86. 1.1 This test method covers a procedure for determination of the distillation characteristics of petroleum products and liquid fuels having boiling range between 208201;°C to 4008201;°C at atmospheric pressure using an automatic micro distillation apparatus. 1.2 This test method is applicable to such products as; light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 208201;% ethanol, aviation gasolines, aviation turbine fuels, regular and low sulfur diesel fuels, biodiesel (B100), biodiesel blends up to 208201;% biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels, and marine fuels. 1.3 The test method is also applicable to hydrocarbons with a narrow boiling range, like organic solvents or oxygenated compounds. 1.4 The test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the appl......

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Micro Distillation Method)

KS B ISO 15547:2015 石油和天然气工业 板式热交换器

Petroleum and natural gas industries-Plate heat exchangers

GSO ISO 13707:2015 石油天然气工业 往复式压缩机

This International Standard covers the minimum requirements for reciprocating compressors and their drivers used in the petroleum and natural gas industries with either lubricated or nonlubricated cylinders. This International Standard may be used for other services or in other industries by agreement. Compressors covered by this International Standard are moderate to low-speed and in critical services. Also included are related lubricating systems, controls, instrumentation, intercoolers, aftercoolers, pulsation suppression devices and other auxiliary equipment. Excluded are integral gas-engine driven compressors, packaged high-speed separable engine-driven reciprocating gas compressors, compressors with single-acting trunk-type (automotive-type) pistons that also serve as crossheads and either plant or instrument air compressors that discharge at gauge pressures of 9 bar or below. Also excluded are gas engine and steam engine drivers.

Petroleum and natural gas industries -- Reciprocating compressors

BS EN ISO 24817:2015 石油,石化和天然气工业.管道综合修理.资格认定,设计,安装,测试和检验

Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection

ISO 24817:2015 石油、石化和天然气工业.管件用复合材料检修. 资格鉴定和设计、安装、试验和检验

This International Standard gives requirements and recommendations for the qualification and design, installation, testing, and inspection for the external application of composite repair systems to corroded or damaged pipework, pipelines, tanks, and vessels used in the petroleum, petrochemical, and natural gas industries.

Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection

ASTM C1318-15 烟气脱硫石灰中总中和能力和溶解的氧化钙和氧化镁的标准测试方法

5.1 There are existing lime-based flue gas desulfurization units in operation that require a method to measure the oxides available for sulfur dioxide absorption. Dissolved magnesium oxide varies among limes depending on the limestone sources and calcination conditions. 1.1 This test method covers analysis of magnesian, dolomitic and high-calcium limes for total neutralizing capability and dissolved major oxides. Dissolved calcium and magnesium are the major species that neutralize acid under the conditions of the test. 1.2 The test conditions are chosen to measure the acid-neutralizing capacity of both calcium hydroxide and magnesium hydroxide contained in slaked lime. By controlling the neutralization pH at 6, magnesium hydroxide and magnesium oxide are titrated in addition to calcium hydroxide fraction. 1.3 This test method also determines the fraction of Mg ions present in the lime that will dissolve under lime flue gas desulfurization (FGD) conditions. Because the Mg++ ion alters FGD performance, it is important to know its concentration. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD)

DL/T 1419-2015 变压器油再生与使用导则

Guidelines for Transformer Oil Regeneration and Use

ASTM C1318-15a 测定烟道气体脱硫 (FGD) 用石灰中的溶解钙, 氧化镁总中和能力的标准试验方法

5.1 There are existing lime-based flue gas desulfurization units in operation that require a method to measure the oxides available for sulfur dioxide absorption. Dissolved magnesium oxide varies among limes depending on the limestone sources and calcination conditions. 1.1 This test method covers analysis of magnesian, dolomitic and high-calcium limes for total neutralizing capability and dissolved major oxides. Dissolved calcium and magnesium are the major species that neutralize acid under the conditions of the test. 1.2 The test conditions are chosen to measure the acid-neutralizing capacity of both calcium hydroxide and magnesium hydroxide contained in slaked lime. By controlling the neutralization pH at 6, magnesium hydroxide and magnesium oxide are titrated in addition to calcium hydroxide fraction. 1.3 This test method also determines the fraction of Mg ions present in the lime that will dissolve under lime flue gas desulfurization (FGD) conditions. Because the Mg2+ ion alters FGD performance, it is important to know its concentration. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD)

GOST R 56522-2015 气体分配系统. 用于现有气体分配网络的经营文档的恢复

Gas distribution systems. Recovery of operational documentation for the existing gas distribution networks

GSO ISO 13631:2014 石油和天然气工业 充气往复式压缩机

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of packaged skid-mounted, reciprocating, separable or integral compressors with lubricated cylinders and their prime movers, for use in the petroleum and natural gas industries for the compression of hydrocarbon gas. It is also applicable to all necessary auxiliary equipment, such as water and gas coolers, silencers, emission control equipment, filters, separators, control panel, piping, etc., required to install an operable unit in compliance with the purchase specifications and with the intent of minimizing field construction and field-purchased equipment. This International Standard is not applicable to the following: — reciprocating compressors for petroleum and natural gas industries covered by ISO 13707; — column-mounted compressors; — non-lubricated compressors; — compressors having trunk-type (automotive-type) pistons that also serve as crossheads; — utility or instrument air compressors with a discharge gauge pressure of 0,9 MPa (9 bar) or less; — compressors driven by diesel engine, gas turbine and steam turbine prime movers.

Petroleum and natural gas industries -- Packaged reciprocating gas compressors

GSO ISO 13705:2014 石油、石化和天然气工业 用于一般炼油厂服务的热炉

ISO 13705:2012 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air heaters, fans and burners for general refinery service. ISO 13705:2012 is not intended to apply to the design of steam reformers or pyrolysis furnaces.

Petroleum, Petrochemical and Natural Gas Industries Fired Heaters for General Refinery Service

ASTM D7344-14 大气压力下石油产品和液体燃料蒸馏的标准试验方法 (微量法)

5.1 The distillation (volatility) characteristics of hydrocarbons and other liquids have an important effect on their safety and performance, especially in the case of fuels and solvents. The boiling range gives information on the composition, the properties, and the behavior of the fuel during storage and use. Volatility is the major determinant of the tendency of a hydrocarbon mixture to produce potentially explosive vapors. 5.2 The distillation characteristics are equally important for both automotive and aviation gasolines, affecting starting, warm-up, and tendency to vapor lock at high operating temperatures or high altitude, or both. The presence of high boiling point components in these and other fuels can significantly affect the degree of formation of solid combustion deposits. 5.3 Volatility, as it affects the rate of evaporation, is an important factor in the application of many solvents, particularly those used in paints. 5.4 Distillation limits are often included in petroleum product specifications, in commercial contract agreements, process refinery/control applications, and for compliance to regulatory rules. 1.1 This test method covers the procedure for the determination of the distillation characteristics of petroleum products and liquid fuels in the range of 208201;°C to 4008201;°C (688201;°F to 7528201;°F) using miniaturized automatic distillation apparatus. 1.2 This test method is applicable to such products as: light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 108201;% ethanol, aviation gasolines, aviation turbine fuels, regular and low sulfur diesel fuels, biodiesel (B100), biodiesel blends up to 208201;% biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels, and marine fuels. 1.3 This test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method)