75.180.20 加工设备 标准查询与下载

DS/EN ISO 10438-1:2008 石油、石化和天然气工业 润滑、轴封和控制油系统和辅助设备 第1部分：一般要求

This part of ISO 10438 specifies general requirements for lubrication systems, oil-type shaft-sealing systems, dry-gas face-type shaft-sealing systems and control-oil systems for general- or special-purpose applications.General-purpose applications are limited to lubrication systems. These systems can serve equipment such as compressors, gears, pumps and drivers.This part of ISO 10438 is intended to be used in conjunction with ISO 10438-2, ISO 10438-3 or ISO 10438-4, as appropriate.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements

LST EN ISO 10440-1:2008 石油、石化和天然气工业 旋转式容积式压缩机 第1部分：过程压缩机（ISO 10440-1:2007）

Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors (ISO 10440-1:2007)

LST EN ISO 10438-2:2008 石油、石化和天然气工业 润滑、轴封和控制油系统和辅助设备 第2部分：专用油系统（ISO 10438-2:2007）

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)

LST EN ISO 10438-3:2008 石油、石化和天然气工业 润滑、轴封和控制油系统和辅助设备 第3部分：通用油系统（ISO 10438-3:2007）

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)

LST EN ISO 10438-4:2008 石油、石化和天然气工业 润滑、轴封和控制油系统及辅助设备 第4部分：自作用气封支持系统（ISO 10438-4:2007）

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)

LST EN ISO 10438-1:2008 石油、石化和天然气工业 润滑、轴封和控制油系统和辅助设备 第1部分：一般要求（ISO 10438-1:2007）

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007)

LST EN ISO 13704:2008 石油、石化和天然气工业 炼油厂加热器管厚度的计算（ISO 13704:2007）

Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2007)

GSO ISO 10441:2008 石油、石化和天然气工业 机械传动用弹性联轴器 特殊应用

This International Standard specifies the requirements for couplings for the transmission of power between the rotating shafts of two machines in special-purpose applications in the petroleum, petrochemical and natural gas industries. Such applications are typically in large and/or high speed machines, in services that can be required to operate continuously for extended periods, are often unspared and are critical to the continued operation of the installation. By agreement, it can be used for other applications or services. Couplings covered by this International Standard are designed to accommodate parallel (or lateral) offset, angular misalignment and axial displacement of the shafts without imposing unacceptable mechanical loading on the coupled machines. It is applicable to gear, metallic flexible element, quill shaft and torsionally resilient type couplings. Torsional damping and resilient type couplings are detailed in Annex A; gear-type couplings are detailed in Annex B and quill shaft style couplings are detailed in Annex C. This International Standard covers the design, materials of construction, manufacturing quality, inspection and testing of special-purpose couplings. This International Standard does not define criteria for the selection of coupling types for specific applications. This International Standard is not applicable to other types of couplings, such as clutch, hydraulic, eddycurrent, rigid, radial spline, chain and bellows types.

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission – Special-purpose applications

GSO ISO 13704:2008 石油天然气工业炼油厂炉管厚度计算

This International Standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes for petroleum refinery heaters. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping. This International Standard does not give recommendations for tube retirement thickness; annex A describes a technique for estimating the life remaining for a heater tube.

Petroleum and Natural Gas Industries – Calculation of Heater-Tube Thickness in Petroleum Refineries

DS/EN ISO 13704:2008 石油、石化和天然气工业 炼油厂加热管厚度的计算

This International Standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for petroleum-refinery heaters. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process-fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping.This International Standard does not give recommend

Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries

BS EN ISO 13704:2008 石油、石化和天然气工业.炼油厂加热管厚度的计算

Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries

BS EN ISO 10438-2:2007 石油、石化和天然气工业 润滑、轴密封和控制油系统及辅助设备 专用油系统

Petroleum, petrochemical and natural gas industries. Lubrication, shaft-sealing and control-oil systems and auxiliaries - Special-purpose oil systems

BS EN ISO 10438-1:2008 石油、石化和天然气工业 润滑,轴封和控油系统及辅助设备 一般要求

Petroleum, petrochemical and natural gas industries. Lubrication, shaft-sealing and control-oil systems and auxiliaries. General requirements

BS EN ISO 10438-2:2008 石油、石化和天然气工业.润滑、轴封和控油系统及辅助设备.专用油系统

ISO 10438-2:2007, in conjunction with ISO 10438-1, specifies requirements for oil systems for special-purpose applications. These oil systems can provide lubrication oil, seal oil or both. These systems can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Special-purpose oil systems

BS EN ISO 10438-3:2008 石油、石化和天然气工业.润滑、轴封和控油系统及辅助设备.专用油系统

ISO 10438-3:2007, in conjunction with ISO 10438-1, specifies requirements for oil systems for general-purpose applications. These oil systems can provide lubrication oil, but not seal oil and can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - General-purpose oil systems

BS EN ISO 10438-4:2008 石油、石化和天然气工业.润滑、轴封、控油系统及辅助装置.自动气封支撑系统

ISO 10438-4:2007 in conjunction with ISO 10438-1 specifies requirements for support systems for self-acting gas seals (dry gas seals), for example as described in ISO 10439 and ISO 10440-1. These systems can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Self-acting gas seal support systems

BS EN ISO 10440-1:2008 石油,石化和天然气工业.旋转型容积式压缩机.加工压缩机

ISO 10440-1:2007 specifies requirements for dry and oil-flooded, helical-lobe rotary compressors used for vacuum or pressure or both in petroleum, petrochemical, and gas industry services. It is intended for compressors that are in special-purpose applications. It is not applicable to general-purpose air compressors, liquid-ring compressors, or vane-type compressors.

Petroleum, petrochemical and natural gas industries. Rotary-type positive-displacement compressors. Process compressors

BS EN ISO 10438-3:2007 石油、石化和天然气工业 润滑、轴密封和控制油系统及辅助设备 通用油系统

Petroleum, petrochemical and natural gas industries. Lubrication, shaft-sealing and control-oil systems and auxiliaries - General-purpose oil systems

BS EN ISO 10438-1:2007 石油,石化和天然气工业.润滑,轴封和控油系统及辅助设备.一般要求

ISO 10438-1:2007 specifies general requirements for lubrication systems, oil-type shaft-sealing systems, dry-gas face-type shaft-sealing systems and control-oil systems for general- or special-purpose applications. General-purpose applications are limited to lubrication systems. These systems can serve equipment such as compressors, gears, pumps and drivers. ISO 10438-1:2007 is intended to be used in conjunction with ISO 10438-2, ISO 10438-3 or ISO 10438-4, as appropriate.

Petroleum, petrochemical and natural gas industries - Lubrication , shaft-sealing and control-oil systems and auxiliaries - General requirements

BS EN ISO 10440-1:2007 石油、石化和天然气工业 旋转式正排量压缩机 工艺压缩机

1   Scope This part of ISO 10440 specifies requirements for dry and oil-flooded, helical-lobe rotary compressors (see Figure 1) used for vacuum or pressure or both in petroleum, petrochemical, and gas industry services. It is intended for compressors that are in special-purpose applications . It is not applicable to general-purpose air compressors, liquid-ring compressors, or vane-type compressors. NOTE Standard air compressors are covered in ISO 10440-2.

Petroleum, petrochemical and natural gas industries. Rotary-type positive-displacement compressors - Process compressors