75.180.30 容积设备和容积测量 标准查询与下载
共找到 531 条与 容积设备和容积测量 相关的标准，共 36 页
Specification for the performance of automatic tank contents gauges
- ICS
- 75.180.30
- CCS
- Q81
- 发布
- 2012-04-30
- 实施
- 2012-04-30
This European Standard specifies the minimum performance requirements for various classes of automatic tank gauges which are limited to static tanks of shop fabricated manufacture both metallic and non metallic, underground and above ground which do not exceed 5 m in height. It is applicable to gauges for fuels (products) which are flammable, having a flash point up to but not exceeding 100 ℃, stored at premises (e. g. filling stations) at which fuel is dispensed for use in vehicles and other forms of transportation.This European Standard applies to gauges suitable for use at ambient temperatures and subject to normal operational pressure variations. Gauging of liquefied gases are not covered byThis standard.This European Standard relates to the measurement of product level, measurement of product temperature and detection of the presence of free water. The detection of free water may be compromised for Alcohol blended fuels. NOTE 1This standard is not intended to cover safety functionalities (i.e. overfill prevention, leak detection, etc.). Further Standards apply. NOTE 2This standard is not intended to cover legal metrology requirements.
Specification for the performance of automatic tank contents gauges
- ICS
- 75.180.30
- CCS
- 发布
- 2012-03-01
- 实施
本标准规定了膜式燃气表膜片的技术要求、试验方法、验收规则及包装、标志、运输与贮存。 本标准适用于膜式燃气表膜片的生产和验收。
Technical specification for membrane gas meter diaphragm
- ICS
- 75.180.30
- CCS
- N 12
- 发布
- 2012-02-15
- 实施
- 2012-06-01
本标准规定了最大流量不超过10m3/h的IC卡膜式燃气表内置电机阀的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于IC卡膜式燃气表内置电机阀的生产和验收。其它带有内置电机阀的燃气表可参照执行。
IC card membrane gas meter built-in motor valve technical specification
- ICS
- 75.180.30
- CCS
- N 12
- 发布
- 2012-02-15
- 实施
- 2012-06-01
Refrigerated hydrocarbon and nonpetroleum based liquefied gaseous fuels. General requirements for automatic tank gauges. Automatic tank gauges for liquefied natural gas on board marine carriers and floating storage
- ICS
- 75.180.30
- CCS
- E98
- 发布
- 2012-01-31
- 实施
- 2012-01-31
Refrigerated hydrocarbon and nonpetroleum based liquefied gaseous fuels. General requirements for automatic tank gauges. Automatic tank gauges for liquefied petroleum and chemical gases on board marine carriers and floating storage
- ICS
- 75.180.30
- CCS
- E98
- 发布
- 2012-01-31
- 实施
- 2012-01-31
This Technical Report establishes minimum provisions for the surveillance, based on available standards from first commissioning, of devices and systems with measuring function throughout their technical life when used in the activities of the categories listed in the Annex I of the European Directive 2003/87/EC. It does so in order to ensure the compliance with the expected maximum allowable difference of indication.This Technical Report applies to devices/systems with the function to measure: volumetric or mass amount of natural gas consumption (any type of gas meters), volumetric amount of natural gas consumption at specified base conditions (conversion
Surveillance from first commissioning on measuring devices used in natural gas supply to the installations of the activities under the Directive 2003/87/EC establishing a scheme of CO2 emissions trading
- ICS
- 75.180.30
- CCS
- 发布
- 2012
- 实施
Crude petroleum and petroleum products -- Determination of density -- Part 4: Petroleum measurement tables
- ICS
- 75.180.30
- CCS
- E04
- 发布
- 2011-11-21
- 实施
This International Standard establishes procedures to achieve the fullness of a pipeline system. This International Standard is applicable to crude oils and petroleum products which are liquid at atmospheric pressure and at the observed temperature. It can be applied to loading, discharges and movements between local storage tanks. It is not the intention of this International Standard to recommend practices for transcontinental movements.
Crude petroleum and petroleum products -- Bulk cargo transfer -- Guidelines for achieving the fullness of pipelines
- ICS
- 75.180.30
- CCS
- 发布
- 2011-10-12
- 实施
This International Standard establishes procedures and describes the recommended practices for the manual and automatic measurement and accounting of bulk quantities of crude petroleum (including spiked, blended and reconstituted crude petroleum) transferred from one port to another by marine tank vessels. This International Standard provides a reliable basis for establishing the quantities of crude petroleum transferred. The procedures apply to the transportation of crude petroleum from loading to discharge.
Crude petroleum -- Transfer accountability – Guidelines for cargo inspection
- ICS
- 75.180.30
- CCS
- 发布
- 2011-10-12
- 实施
This International Standard specifies a method for assessing small volumes of material in the cargo tanks of marine tanker vessels prior to loading (OBQ) or upon completion of discharge (ROB) by manual gauging. It is not applicable to the estimation of clingage, hydrocarbon vapours or the contents of associated pipelines or pumps.
Crude petroleum and petroleum products -- Transfer accountability -- Assessment of on board quantity (OBQ) and quantity remaining on board (ROB)
- ICS
- 75.180.30
- CCS
- 发布
- 2011-10-12
- 实施
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels - General requirements for automatic tank gauges - Part 1: Automatic tank gauges for liquefied natural gas on board marine carriers and floating storage
- ICS
- 75.180.30
- CCS
- N12
- 发布
- 2011-08
- 实施
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels - General requirements for automatic tank gauges - Part 3: Automatic tank gauges for liquefied petroleum and chemical gases on board marine carriers and floating storage
- ICS
- 75.180.30
- CCS
- N12
- 发布
- 2011-08
- 实施
Appendix B and all other pertinent requirements of this specification shall be used as the basis for developing detailed design and construction of foundations for storage tanks. 1.1.9 Additional requirements for external floating roofs are contained in Appendix C of this specification. 1.1.13 Additional requirements for optional self-supporting aluminum dome roofs are contained in Appendix G of this specification. 1.1.14 Additional requirements for internal floating roofs are contained in Appendix H of this specification.
Oil & Gas Atmospheric Tanks Specifications – Manufacture of Atmospheric Tanks
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
This specification defines the minimum mandatory requirements governing material, mechanical design, fabrication, erection, inspection, and testing of low-pressure storage tanks. 1.1.2 This specification does not cover tanks designed in accordance with Appendix Q "Low-Pressure Storage Tanks for Liquefied Hydrocarbons Gases" and double wall tanks according to Appendix R "Low-Pressure Storage Tanks for Refrigerated Products" of API STD 620. Additional requirements for such tanks shall be developed, if necessary, by the Design Engineer. Such requirements shall be submitted to the Company’s Engineer prior to bidding with sufficient time for review. 1.1.3 This specification shall be attached to and form an integral part of a purchase order. 1.1.4 Conflicts and Deviations 1.1.4.1 Any conflicts between this specification and other Company’s Materials System Specifications (CMSSs), Company’s Engineering Standards (CESs), Industry codes and standards, and Company’s Standard Drawings (CSDs) and Forms shall be resolved in writing by the Company or Buyer Representative. 1.1.4.2 Direct all requests to deviate from this specification in writing to the Company or Buyer Representative. 1.2 Coverage 1.2.5 (Exception) Horizontal cylindrical tanks used for the storage of hydrocarbon liquids within the scope of API STD 620, with design pressures in their gas or vapor spaces not more than 103 kPa gauge (15 psig).
Manufacture of Low Pressure Tanks
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
This International Standard specifies methods, procedures and equipment for the manual measurement of the temperature of bulk quantities of petroleum and petroleum products in storage tanks. The preferred method is to use a portable electronic thermometer as described in clause 7. Other methods included use permanently installed indicating thermometers of the spot-measurement type and temperature determination by sampling methods using cup-case thermometers, flushing-case thermometers, and thermometers within conventional tank samples taken in accordance with ISO 3170. This International Standard excludes averaging thermometers forming part of an automatic gauging system. These are described in ISO 4266. It is realized that, in many countries, some or all of the items covered by this International Standard are the subject of mandatory regulations imposed by the laws of those countries; such regulations must be rigorously observed. In cases of conflict between such mandatory regulations and this International Standard, the former prevails.
Petroleum and liquid petroleum products – Temperature measurements -- Manual methods
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
This International Standard specifies the standard reference conditions of pressure and temperature for measurements carried out on crude petroleum and its products, including liquefied petroleum gases. It excludes natural gas.
Petroleum liquids and liquefied petroleum gases – Measurement - Standard reference conditions
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
This part of ISO 18132 establishes the general requirements for the specification, installation and calibration/verification testing of automatic level gauges (ALG) used for refrigerated light hydrocarbon fluids, i.e., LNG and LPG, stored in bulk storage tanks on shore at pressures close to atmosphere. This part of ISO 18132 is not applicable to pressurized shore tanks.
Refrigerated light hydrocarbon fluids – General requirements for automatic level gauges – Part 2: Gauges in refrigerated-type shore tanks
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
This part of ISO 4266 gives guidance on the selection, accuracy, installation, commissioning, calibration and verification of automatic tank thermometers (ATTs) in fiscal/custody transfer applications in which the ATT is used for measuring the temperature of petroleum and liquid petroleum products having a Reid vapour pressure less than 100 kPa, stored in atmospheric storage tanks. This part of ISO 4266 is not applicable to the measurement of temperature in caverns or in refrigerated storage tanks.
Petroleum and liquid petroleum products – Measurement of level and temperature in storage tanks by automatic methods – Part 4 : Measurement of temperature in atmospheric tanks
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
General 1.1.1 The company defines the minimum mandatory requirements governing material, design, fabrication, inspection, and testing of small, atmospheric pressure storage tanks used in production, process plant, bulk plant, building services, fuel dispensing, or community facilities applications. 1.1.2 This specification covers tanks used for the aboveground or underground storage of flammable and combustible liquids. It also covers tanks used for the storage of chemicals or water. 1.1.3 Tanks purchased in accordance with the various industry standards and specifications shall also meet the requirements contained within the body of this specification, plus the supplementary requirements contained in the appendices of this specification as follows.
Oil & Gas Small Tanks Specifications – Manufacture of Small Tanks
- ICS
- 75.180.30
- CCS
- 发布
- 2011-04-12
- 实施
