75.180.99 其他石油和天然气工业设备 标准查询与下载

SH/T 3532-2005 石油化工换热设备施工及验收规范

本规范规定了换热设备安装的技术要求和质量标准。 本规范适用于石油化工新建、扩建和改建工程中公称压力小于或等于35MPa、非直接受火的管式和板式换热设备的施工及验收。检修工程可参照执行。

Specification for construction and acceptance of heat-exchange equipment in petrochemical industry

BS EN ISO 13503-3:2005 石油和天然气工业.完井液和材料.重盐水试验

ISO 13503-3:2005 covers the physical properties, potential contaminants and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion and workover fluids. ISO 13503-3:2005 provides methods for assessing the performance and physical characteristics of heavy brines for use in field operations. It includes procedures for evaluating the density or specific gravity, the clarity or amount of particulate matter carried in the brine, the crystallization point or the temperature (both ambient and under pressure) at which the brines make the transition between liquid and solid, the pH, and iron contamination. It also contains a discussion of gas hydrate formation and mitigation, brine viscosity, corrosion testing, buffering capacity and a standardised reporting form. ISO 13503-3:2005 is intended for the use of manufacturers, service companies and end-users of heavy brines.

Petroleum and natural gas industries - Completion fluids and materials - Testing of heavy brines

NF M87-272-1:2005 石油和天然气工业.完井液和材料.第1部分:完井液粘着特性的测量.

Petroleum and natural gas industries - Completion fluids and materials - Part 1 : measurement of viscous properties of completion fluids.

BS 1435-2:2005 抽油和排油用橡胶软管组件.贮存、试验和使用建议

This British Standard recommends conditions for the storage, testing and use of rubber hose assemblies manufactured in accordance with BS EN 1765. It provides advice on the storage, testing and use of rubber hose assemblies for oil suction and discharge duties commonly used for transferring crude oil and other liquid petroleum products, excluding liquid petroleum gas (LPG) and natural gas, to and from tanker and bunkering vessels or for similar duties ashore.

Rubber hose assemblies for oil suction and discharge services - Recommendations for storage, testing and use

CJ/T 33-2004 液化石油气钢瓶热处理工艺评定

本标准规定了液化石油气钢瓶热处理工艺、设备等基本要求，热处理工艺评定程序及质量检验等。 本标准适用于正常环境温度(-40℃～+60℃)下使用的，水压试验压力不大于3.3MPa，公称容积小于240L可重复充装液化石油气的钢质焊接气瓶。

Technological process evaluation of heat treatment for LPG cylinders

SH 3533-2003 石油化工给水排水管道工程 施工及验收规范

本规范规定了设计压力小于或等于1．6MPa的给水排水管道工程施工的要求及质量标准。 本规范适用于石油化工工程建设的新建、改扩建工程的给水排水埋地和地上管道的施工及验收。改造、检修等工程可参照执行。 石油化工给水排水管道工程包括下列管道和管道构筑物： a) 管道： 1) 生产及生活给水管道： 2) 消防管道： 3) 循环用水管道； 4) 生产及生活污水管道； 5) 雨水管道： 6) 水质处理及循环冷却设施中的管道。 b) 管道构筑物： 1) 给水排水井室； 2) 取(排)水口： 3) 支(挡)墩。 本规范不适用于下列给水排水管道： a) 建筑物内部的生活给水排水管道； b) 管渠类输水管道。 注：管渠类输水管道指采用砖、石及混凝土砌块砌筑和采用钢筋混凝土现场浇筑及钢筋混凝土预制构件装配的圆形、矩形、拱形等异形截面的输水管道。

Specification for the construction and acceptance of piping works for watersupply and drainage in petrochemical industry

BS ISO 13503-1:2003 石油和天然气工业.完井液和材料.完井液粘性的测量

This part of ISO 13503 provides consistent methodology for determining the viscosity of completion fluids used in the petroleum and natural gas industries. For certain cases, methods are also provided to determine the rheological properties of a fluid.

Petroleum and natural gas industries - Completion fluids and materials - Measurement of viscous properties of completion fluids

CJ/T 34-2002 液化石油气钢瓶涂覆规定

本标准规定了液化石油气钢瓶涂覆的技术要求，检验方法和检验规则。 本标准适用于正常环境温度(-40℃～60℃)下使用的可重复盛装液化石油气的钢质焊接气瓶的表面涂覆。

Coating regulations for liquefied petroleum gas cylinders

CSA 6.20-2000(R2005) 燃气用具的组合燃气控制装置

1.1 Scope 1.1.1 This standard applies to newly produced combination gas controls (see Definitions, Part IV), hereinafter referred to as controls, constructed entirely of new, unused parts and materials. 1.1.2 The combination control may include other functions such as pilot gas filters, pressure switches, etc., which shall be of an approved type (see Definitions, Part IV), or shall be investigated as an integral part of the combination control for construction and performance equivalent to an approved type. A control which incorporates two or more automatic valves and no other function, (as defined by combination control, see Definitions, Part IV), may be tested to this standard or Z21.21-CGA 6.5, automatic gas valve standard, at the discretion of the manufacturer. 1.1.3 Compliance of a combination control with this standard does not imply that the combination control is acceptable for use on gas appliances without supplemental tests with the combination control applied to the particular appliance design. 1.1.4 This standard applies to combination controls having a maximum operating gas pressure of ½ psi (3.45 kPa) with one or more of the following fuel gases: natural, manufactured, mixed, liquefied petroleum and liquefied petroleum gas-air mixtures. 1.1.5 This standard applies to combination controls which are capable of operation in ambient temperatures of 32°F (O°C) to 125°F (51.5°C), unless a higher temperature, lower temperature or both, are specified by the manufacturer. 1.1.6 Exhibit A contains items unique to the U.S. 1.1.7 Exhibit B contains items unique to Canada. 1.1.8 Exhibit C contains a list of standards specifically referenced in this standard, and sources from which these reference standards may be obtained. 1.1.9 If a value for measurement as given in this standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. 1.1.10 All references to psi through this standard are to be considered gage pressure unless other specified.

Combination Gas Controls for Gas Appliances

DS/EN 12838:2000 液化天然气装置和设备 LNG 取样系统的适用性测试

This standard specifies the tests to be carried out in order to assess the suitability of LNG sampling systems designed to determine the composition of Liquefied Natural Gas, in combination with an analytical device such as a chromatograph.

Installations and equipment for liquefied natural gas - Suitability testing of LNG sampling systems

BS 1600:1991 石油工业用钢管尺寸规范

This British Standard specifies the dimensions in metric units for steel pipe commonly used by the petroleum industry.NOTE. The titles of the publications referred to in this standard are listed on the inside back cover.

Specification for dimensions of steel pipe for the petroleum industry

BS 1600:1992 石油工业用钢管尺寸规范

Specification for dimensions of steel pipe for the petroleum industry

BS 5173-102.3:1988 橡胶和塑料软管及软管组件试验方法.第102部分:液压试验.第3节:燃料分配泵软管体积膨胀测定

This Section of BS 5173 describes two methods of measuring the volumetric expansion of a hose assembly at a specified pressure, in one the hose is twisted axially and in the other it is not. The tests are applicable to fuel-dispensing pump hoses only. NOTE. The titles of the publications referred to in this standard are listed on page 3.

Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Determination of volumetric expansion of fuel-dispensing pump hoses

BS 3492:1987 公路和铁路运输石油产品（包括航空燃油）油罐车软管及软管组件规范

Eight types of hoses for conveying gasoline fuels and oils, including aviation fuels having an aromatic hydrocarbon content of not more than 50%, at temperatures up to 80C and a vacuum not exceeding 500 mbar.

Specification for road and rail tanker hoses and hose assemblies for petroleum products, including aviation fuels

BS 2464-4:1980 汽油、石油和润滑剂用软管接头规范.第4部分:欧洲型 100mm快速接头规范

Requirements for materials, dimensions, testing and use of the 100 mm quick-acting hose coupling preferred by the majority of EEC countries for the transfer of petrol, oil and lubricants to and from road and rail tank wagons at working pressures up to 20 bar.

Hose couplings for petrol, oil and lubricants - Specification for 100 mm quick-acting couplings: European type

EN 1868:1975+A1:1975 石油、石化和相关工业用钢制止回阀（法兰和对焊端）规范

Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries

BS 1868:1975 石油、石化及联合企业用钢制单向阀(有法兰及对焊端)规范

Nominal sizes, ratings, design, materials, marking and shipping for swing, piston, ball and disk valves for Class 150 up to Class 2500 and of nominal sizes 15 to 600 mm. Appendix for application to piping systems with BS 4504:Part 1.

Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries

BS 1868:1975+A1:1990 石油、石化及联合工业用钢制止回阀(有法兰及对焊端)用规范

This British Standard specifies requirements for cast or forged steel check valves with flanged or butt-welding ends of the following types: a) swing, for vertical or horizontal flow (see Figure 1); b) lift: i) piston type, for angle or horizontal flow (see Figure 2); ii) ball type, for angle or horizontal flow (see Figure 3); iii) ball type, for vertical flow (see Figure 4); iv) disk type, for vertical flow (see Figure 5). The terms “vertical”, “horizontal” and “angle” relate to the axes of the body ends. When swing check valves are used in vertical lines the flow must be in an upward direction. For the purposes of this standard any line with a slope (upward or downward) of 5° or less is deemed to be horizontal. In the case of angle pattern valves the inlet should be vertical.

Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries

BS 1873:1975 石油、石化及有关工业用钢球形阀、球形截止阀与单向阀(有法兰及对接焊端)规范

Straight, angle and (oblique) Y pattern with flanged or butt-welding ends in nominal sizes from 15 to 400 mm ($9H to 16 in) and Class 150 to 2500.

Specification for steel globe and globe stop and check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries

BS 3799:1974 石油工业用钢管配件、螺旋管接头和套管焊接规范

Forged carbon and alloy steel screwed and socket-welding fittings. Screw threads in accordance with API Std. 5B. Bore diameters of socket-welding fittings compatible with BS 3600 and BS 1600. Substantially agrees with ANSI B16.11, ASTM A 234 and ASTM A 403.

Specification for steel pipe fittings, screwed and socket-welding for the petroleum industry