77.120.30 铜和铜合金 标准查询与下载

GOST R 57060-2016 铜. 采用感应耦合等离子体原子发射光谱法测量铜的杂质质量分数

Copper. Measurement of impurities mass fraction in copper by an inductively coupled plasma atomic emission spectrometry method

GOST R 57376-2016 铜锭. 规格

Copper ingots. Specifications

GOST R 57061-2016 铜. 采用感应耦合等离子体质谱法测量铜的杂质质量分数

Copper. Measurement of impurities mass fraction in copper by an inductively coupled plasma mass spectrometry method

ASTM B154-16 铜合金硝酸亚汞试验的标准试验方法

5.1 This test method is an accelerated test for detecting the presence of residual (internal) stresses that might result in failure of individual parts in storage or in service due to stress corrosion cracking. 5.2 This test method is not intended for use on assemblies or parts under applied stress. If used for that purpose, the results shall be for information only and not a cause for rejection of the assembly, its component parts, or the original mill product. 1.1 This test method describes the technique for conducting the mercurous nitrate test for residual stresses in wrought copper alloy mill products. Note 1: For any particular copper alloy, reference should be made to the material specification. Note 2: Test Method B858 may be considered as a possible alternative test method which does not involve the use of mercury. Note 3: This test method is considered historically reliable for determining the potential state of residual stress in copper alloys, but not promoted for use due to the hazards relating to mercury use and environmentally appropriate disposal. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determines the applicability of regulatory limitations prior to use. For specific precautionary and hazard statements see Sections 1, 6, and8201;7. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.)

Standard Test Method for Mercurous Nitrate Test for Copper Alloys

KS D 2366-2015 铜及铜合金废料

Copper and copper alloys Scrap

KS D ISO 1190-1-2015 铜及铜合金 名称代码 第1部分：材料名称

Cooper and copper alloys－Code of designation－Part 1：Designation of materials

KS D ISO 1190-1:2015 铜和铜合金 名称与牌号表示规则 第1部分：材料的名称与符号

Cooper and copper alloys-Code of designation-Part 1:Designation of materials

GSO ISO 1811-1:2015 铜和铜合金化学分析样品的选择和制备 第1部分：未成型铸造产品的取样

  Scope is not provided for this standard

Copper and copper alloys -- Selection and preparation of samples for chemical analysis -- Part 1: Sampling of cast unwrought products

GSO ISO 2543:2015 铜及铜合金锰的测定分光光度法

  Scope is not provided for this standard

Copper and copper alloys -- Determination of manganese -- Spectrophotometric method

GSO ISO 1554:2015 成型和铸造铜合金 铜含量的测定 电解法

  Scope is not provided for this standard

Wrought and cast copper alloys -- Determination of copper content -- Electrolytic method

GSO ISO 1812:2015 铜合金 铁含量的测定 分光光度法 1.10 菲咯啉

  Scope is not provided for this standard

Copper alloys -- Determination of iron content -- 1,10- Phenanthroline spectrophotometric method

JB/T 12283-2015 饮用水系统零部件用黄铜铸件

本标准规定了饮用水系统零部件用黄铜铸件（以下简称铸件）的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于采用砂型铸造、金属型铸造生产的饮用水系统零部件用黄铜铸件。

Brass castings for drinking water system components

JIS H 1059:2015 铜和铜合金.砷含量测定

Copper and copper alloys -- Determination of arsenic content

GSO ISO 6437:2015 铜合金 铬含量的测定 滴定法

This International Standard specifies a titrimetric method for the determination of the total chromium content of copperchromium alloys listed in International Standards. The method is applicable to products having chromium contents between 0,10 and 2,0 % (m/m) .

Copper alloys -- Determination of chromium content -- Titrimetric method

BS EN 15079:2015 铜及铜合金 火花光学发射光谱法(S-OES)分析

Copper and copper alloys. Analysis by spark optical emission spectrometry (S-OES)

BS PD CEN/TS 15656:2015 铜和铜合金.磷含量的测定.分光光度法

Copper and copper alloys. Determination of phosphorus content. Spectrophotometric method

YS/T 990.17-2015 冰铜化学分析方法 第17部分：钴量的测定 原子吸收光谱法

Methods for chemical analysis of matte Part 17: Determination of cobalt content Atomic absorption spectrometry

PD CEN/TS 15656:2015 铜和铜合金 磷含量的测定 分光光度法

This Technical Specification specifies a molybdovanadate spectrophotometric method for the determination of phosphorus in copper and copper alloys in the form of castings or unwrought or wrought products. The method is applicable to products having phosphorus mass fractions between 0,001 % and 0,5 %.

Copper and copper alloys - Determination of phosphorus content - Spectrophotometric method

NF A08-701-1*NF EN 15063-1:2015 铜和铜合金.用波长分布X-射线荧光光谱法(XRF)测定主要结构和杂质.第1部分:常规测量指南

La présente Norme européenne fournit des lignes directrices sur les concepts et les modes opératoires d'étalonnage et d'analyse du cuivre et des alliages de cuivre par spectrométrie de fluorescence X à dispersion en longueur d'onde.

Copper and copper alloys - Determination of main constituents and impurities by wavelength dispersive X-ray fluorescence spectrometry (XRF) - Part 1 : guidelines to the routine method

ASTM B224-15 铜的标准分类

4.1 This classification lists the types of copper available from refineries or fabricators, or both, defines the common terms used, and gives the characteristics of many of the coppers available. It is useful to the neophyte looking for the appropriate copper for a particular application. 1.1 This is a classification of the various types of copper currently available in refinery shapes and wrought products in commercial quantities. It is not a specification for the various types of copper. 1.2 In this classification, use is made of the standard copper designations in use by the copper industry. 1.3 Although this classification includes certain UNS designations as described in Practice E527, these designations are for cross-reference only and are not requirements. Therefore, in case of conflict, this ASTM classification shall govern. 1.4 This classification does not attempt to differentiate between all compositions that could be termed either coppers or copper-base alloys, but in conformance with general usage in the trade, includes those coppers in which the copper plus specific permitted elements is specified as 99.858201;% or more, silver being counted as copper. Note 1: Coppers may contain small amounts of certain elements intentionally permitted to impart specific properties, without excessively lowering electrical conductivity. The total copper plus specific permitted elements is specified as 99.858201;% or more. These intentionally permitted elements normally include, but are not limited to, arsenic, cadmium, chromium, lead, magnesium, silver, sulfur, tellurium, tin, zinc, and zirconium, plus deoxidizers, up to specific levels adopted by the International Standards Organization.

Standard Classification of Coppers