77.140.10 热处理钢 标准查询与下载

KS D 3703-2007(2022) 不锈钢丝

Stainless steel wires

KS D 4106-2007(2012) 焊接结构钢铸件

Steel castings for welded structure

KS D 3703-2007(2017) 不锈钢丝

Stainless steel wires

KS D 0101-2007(2017) 电弧炉的热平衡

Heat balance of arc furnace

KS D 0101-2007 电弧炉热平衡试验方法

이 규격은 아크로(다른 연료에 의하여 예열되는 경우도 포함한다.)의 실용적인 시험에서의 열

Heat balance of arc furnace

KS D 0101-2007(2022) 电弧炉热平衡

Heat balance of arc furnace

SANS 1431:2007 可焊接结构钢

Covers requirements for 12 grades of structural steel available in the form of plates, sections and bars, and suitable for bolted, riveted or welded structures.

Weldable structural steels

ASTM A709/A709M-07 桥梁用结构钢标准规范

1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. Nine grades are available in four yield strength levels as follows:1.1.1 Grades 36 [250], 50 [345], 50S [345S], 50W [345W], 100 [690], and 100W [690W] are also included in Specifications A 36/A 36M, A 572/A 572M, A 992/A 992M, A 588/A 588M, and A 514/A 514M, respectively. When the supplementary requirements of this specification are specified, they exceed the requirements of Specifications A 36/A 36M, A 572/A 572M, A 992/A 992M, A 588/A 588M, and A 514/A 514M. 1.1.2 Grades 50W [345W], HPS 50W [HPS 345W], HPS 70W [HPS 485W], 100W [690W], and HPS 100W [HPS 690W] have enhanced atmospheric corrosion resistance (see ). Product availability is shown in . 1.2 Grade HPS 70W [HPS 485W], 100 [690], 100W [690W], or HPS 100W [HPS 690W] shall not be substituted for Grades 36 [250], 50 [345], 50S [345S], 50W [345W], or HPS 50W [HPS 345W]. Grade 50W [345W], or HPS 50W [HPS 345W] shall not be substituted for Grades 36 [250], 50 [345] or 50S [345S] without agreement between the purchaser and the supplier. 1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A 6/A 6M for information on weldability. 1.4 For structural products to be used as tension components requiring notch toughness testing, standardized requirements are provided in this standard, and they are based upon American Association of State Highway and Transportation Officials (AASHTO) requirements for both fracture critical and non-fracture critical members.1.5 Supplementary requirements are available but shall apply only if specified in the purchase order. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way. 1.7 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A 6/A 6M apply.

Standard Specification for Structural Steel for Bridges

DIN EN 10083-3:2007 淬火和回火钢.第3部分:合金钢交货技术条件.英文版本DIN EN 10083-3-2007-01

This part of EN 10083, in addition to Part 1, specifies the technical delivery requirements for: - semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTES 2 and 3 in EN 10083-1:2006, Clauses 1), - bars (see NOTE 2 in EN 10083-1:2006, Clause 1), - rod, - wide flats, - hot-rolled strip and sheet/plate, - forgings (see NOTE 2 in EN 10083-1:2006, Clause 1), manufactured from the direct hardening alloy steels for quenching and tempering and the alloy flame and induction hardening steels and supplied in one of the heat treatment condidions given for the different types of products in Table1, lines 2 to 6, and in one of the surface conditions given in Table2. The steels are generally intended for the fabrication of quenched and tempered, flame or induction hardened machine parts. The requirements for mechanical properties given in this document are restricted to the sizes given in Table 8. NOTE This document does not apply for bright steel products. For bright steel procucts EN 10277-1 and EN 10277-5 apply. In special cases, variations in these technical delivery requirements or additions to them may be agreed at the time of enquiry and order (see Annex A).

Steels for quenching and tempering - Part 3: Technical delivery conditions for alloy steels; English version of DIN EN 10083-3:2007-01

NF A35-552-1:2006 淬火和回火钢.第1部分:一般交货技术条件

Steels for quenching and tempering - Part 1 : general technical delivery conditions.

NF A35-552-2:2006 淬火钢和回火钢.第2部分:非合金优质钢的交货技术条件

Steels for quenching and tempering - Part 2 : technical delivery conditions for non alloy steels.

NF A35-552-3:2006 淬火钢和回火钢.第3部分:合金钢的交货技术条件

Steels for quenching and tempering - Part 3 : technical delivery conditions for alloy steels.

LST EN 10083-1-2006 淬火和回火用钢 第1部分：一般技术交货条件

Steels for quenching and tempering - Part 1: General technical delivery conditions

LST EN 10083-3-2006 淬火和回火用钢 第3部分：合金钢的技术交货条件

Steels for quenching and tempering - Part 3: Technical delivery conditions for alloy steels

LST EN 10083-2-2006 淬火和回火用钢 第2部分：非合金钢的技术交货条件

Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels

DIN EN 10083-1:2006 淬火和回火钢.第1部分:一般交货技术条件

This part of EN 10083 specifies the general technical delivery requirements for - semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTES 2 and 3), - bars (see NOTE 2), - rod, - wide flats, - hot-rolled strip and sheet/plate, - forgings (see NOTE 2) manufactured from the direct hardening non alloy steels for quenching and tempering (see EN 10083-2), the direct hardening alloy steels for quenching and tempering (see EN 10083-3), the non alloy flame and induction hardening steels (see EN 10083-2) and the alloy flame and induction hardening steels (see EN 10083-3), and supplied in one of the heat treatment conditions given for the different types of products in the relevant tables of EN 10083-2 and EN 10083-3 and in one of the surface conditions given in the relevant tables of EN 10083-2 and EN 10083-3. The steels are generally intended for the manufacture of quenched and tempered, flame or induction hardened machine parts, but can also be used in the normalized condition (see EN 10083-2). Where applicable, the requirements for mechanical properties given in EN 10083-2 and EN 10083-3 are restricted to the relevant tables in these documents. NOTE 1 European Standard on similar grades are listed in Annex C. NOTE 2 Hammer forged semi-finished products (blooms, billets, slabs etc.), seamless rolled rings and hammer forged bars are in the following covered under semi-finished products or bars and not under the term "forgings". NOTE 3 Special agreements should be made when ordering un-worked continuously cast semi-finished products. NOTE 4 In accordance with EN 10020, the steels covered by EN 10083-2:2006 are quality and special steels, the steels covered by EN 10083-3:2006 are special steels. The differences between quality and special steels are characterized by the following requirements, which are valid for special steels only: - the minimum impact values in the quenched and tempered condition (for non alloy special steels in the case of mean percentages by mass of carbon < 0,50 % only); - limiting hardenability values in the Jominy test (for non alloy steels in the case of percentages by mass of carbon > 0,30 % only); - limited oxide inclusion content; - lower maximum contents for phosphorus and sulphur. NOTE 5 This European Standard does not apply for bright steel products. For bright steel products EN 10277-1 and EN 10277-5 apply. In special cases, variations in these technical delivery requirements or additions to them may be agreed at the time of enquiry and order (see Annex B). In addition to the specifications of this Euorpean Standard, the general technical delivery conditions given in EN 10021 are applicable unless otherwise specified.

Steels for quenching and tempering - Part 1: General technical delivery conditions; English version of DIN EN 10083-1:2006-10

BS DD CEN/TR 10347:2006 热处理钢结构构成指南

This CEN Technical Report provides guidance for forming during processing of structural steel products conforming to EN 10025 Parts 2 to 6 and EN 10149 Parts 2 and 3. This Technical Report covers hot and cold forming processes and local hot forming used in flame-straightening operations. This Technical Report does not cover the special measures necessary for the fabrication of structural components that are subjected predominantly to alternating stresses or that come into contact with aggressive media.

Guidance for forming of structural steels in processing

DD CEN/TR 10347:2006 结构钢加工成型指南

This CEN Technical Report provides guidance for forming during processing of structural steel products conforming to EN 10025 Parts 2 to 6 and EN 10149 Parts 2 and 3. This Technical Report covers hot and cold forming processes and local hot forming used in flame-straightening operations. This Technical Report does not cover the special measures necessary for the fabrication of structural components that are subjected predominantly to alternating stresses or that come into contact with aggressive media.

Guidance for forming of structural steels in processing

BS EN 10083-1:2006 淬硬钢和回火钢.通用交货技术条件

This part of EN 10083 specifies the general technical delivery requirements for - semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTES 2 and 3), - bars (see NOTE 2), - rod, - wide flats, - hot-rolled strip and sheet/plate, - forgings (see NOTE 2) manufactured from the direct hardening non alloy steels for quenching and tempering (see EN 10083-2), the direct hardening alloy steels for quenching and tempering (see EN 10083-3), the non alloy flame and induction hardening steels (see EN 10083-2) and the alloy flame and induction hardening steels (see EN 10083-3), and supplied in one of the heat treatment conditions given for the different types of products in the relevant tables of EN 10083-2 and EN 10083-3 and in one of the surface conditions given in the relevant tables of EN 10083- 2 and EN 10083-3. The steels are generally intended for the manufacture of quenched and tempered, flame or induction hardened machine parts, but can also be used in the normalized condition (see EN 10083-2). Where applicable, the requirements for mechanical properties given in EN 10083-2 and EN 10083-3 are restricted to the relevant tables in these documents. NOTE 1 European Standards on similar grades are listed in Annex C. NOTE 2 Hammer forged semi-finished products (blooms, billets, slabs etc.), seamless rolled rings and hammer forged bars are in the following covered under semi-finished products or bars and not under the term "forgings". NOTE 3 Special agreements should be made when ordering un-worked continuously cast semi-finished products. NOTE 4 In accordance with EN 10020, the steels covered by EN 10083-2:2006 are quality and special steels, the steels covered by EN 10083-3:2006 are special steels. The differences between quality and special steels are characterized by the following requirements, which are valid for special steels only: - the minimum impact values in the quenched and tempered condition (for non alloy special steels in the case of mean percentages by mass of carbon < 0,50 % only); - limiting hardenability values in the Jominy test (for non alloy steels in the case of percentages by mass of carbon > 0,30 % only); - limited oxide inclusion content; - lower maximum contents for phosphorus and sulphur. NOTE 5 This European Standard does not apply for bright steel products. For bright steel products EN 10277-1 and EN 10277-5 apply. In special cases, variations in these technical delivery requirements or additions to them may be agreed at the time of enquiry and order (see Annex B). In addition to the specifications of this European Standard, the general technical delivery conditions given in EN 10021 are applicable unless otherwise specified.

Steels for quenching and tempering - General technical delivery conditions

BS EN 10083-3:2006 淬硬钢和回火钢.合金钢的交货技术条件

This part of EN 10083, in addition to Part 1, specifies the technical delivery requirements for: - semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTES 2 and 3 in EN 10083-1:2006, Clause 1), - bars (see NOTE 2 in EN 10083-1:2006, Clause 1), - rod, - wide flats, - hot-rolled strip and sheet/plate, - forgings (see NOTE 2 in EN 10083-1:2006, Clause 1), manufactured from the direct hardening alloy steels for quenching and tempering and the alloy flame and induction hardening steels and supplied in one of the heat treatment conditions given for the different types of products in Table 1, lines 2 to 6, and in one of the surface conditions given in Table 2. The steels are generally intended for the fabrication of quenched and tempered, flame or induction hardened machine parts. The requirements for mechanical properties given in this document are restricted to the sizes given in Table 8. NOTE This document does not apply for bright steel products. For bright steel products EN 10277-1 and EN 10277-5 apply. In special cases, variations in these technical delivery requirements or additions to them may be agreed at the time of enquiry and order (see Annex A).

Steels for quenching and tempering — Part 3: Technical delivery conditions for alloy steels