77.140.30 承压钢 标准查询与下载

ASTM A844/A844M-21 用直接淬火法生产的压力容器用9%镍合金钢板的标准规范

1.1 This specification covers 9 % nickel-alloy steel plates produced by the direct-quenching process. The plates are intended primarily for use in welded pressure vessels. 1.2 The direct-quenching process consists of quenching the plates directly after rolling, without permitting the plates to cool below the critical temperature prior to initiation of the quenching operation, and subsequently tempering the plates (see Appendix X1). (Note: The direct-quenching process differs from the “conventional” process in which the plates are permitted to cool to a temperature significantly below the critical temperature, usually to ambient temperature, prior to reheating to a temperature above the upper critical temperature, then quenching, and subsequently tempering.) 1.3 If the plates are subjected to warm forming, the temperature shall not exceed 950°F [510°C]. 1.4 The maximum nominal thickness of plates furnished under this specification shall not exceed 2 in. [50 mm]. 1.5 This material is susceptible to magnetization. Use of magnets in handling after heat treatment should be avoided if residual magnetism would be detrimental to subsequent fabrication or service. 1.6 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Plates, 9 %  Nickel Alloy, for Pressure Vessels, Produced by the Direct-Quenching Process

UNI EN 10222-2-2021 压力用途钢锻件 第2部分：具有特定高温性能的铁素体和马氏体钢

Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties

JIS G 4110:2021 高温压力容器用高强度铬钼和铬钼钒合金钢板

High strength chromium-molybdenum and chromium-molybdenum-vanadium alloy steel plates for pressure vessels under high-temperature service

JIS G 3127:2021 低温压力容器用镍钢板

Nickel steel plates for pressure vessels for low temperature services

ASTM A543/A543M-09(2021) 淬火和回火镍铬钼合金钢压力容器板的标准规范

1.1 This specification2 covers nickel-chromiummolybdenum alloy steel plates for use in the quenched and tempered condition, intended for the fabrication of welded pressure vessels and other pressure equipment. These alloy compositions are normally considered for construction involving plate thicknesses of 2 in. [50 mm] or greater. 1.2 Material under this specification is available in two types, B and C. The material is also available in three classes as follows: Class Minimum Tensile Strength, ksi [MPa] 1 105 [725] 2 115 [795] 3 90 [620] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements. 1.4 The minimum plate thickness is 3⁄16 in. [5 mm]. 1.5 These alloy steel plates in the as-rolled condition are sensitive to cracking during flame cutting, transit, and handling. They should be shipped in the as-rolled condition only with the mutual agreement of the manufacturer and the purchaser or fabricator. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered Nickel-Chromium-Molybdenum

ASTM A1014/A1014M-16(2021) 高温设备用沉淀硬化螺栓连接（UNS N07718）的标准规范

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of “bolting.” 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inchpound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

KS D 4129-2021 高温压力容器用高强度铬钼合金钢锻件

High strength chromium molybdenum alloy steel forgings for pressure vessels under high-temperature service

KS D 3630-2021 高温压力容器用高强度铬钼合金钢板

High strength chromium molybdenum alloy steel plates for pressure vessels under high-temperature service

DIN EN 10222-2:2021 压力用途钢锻件 第2部分：具有特定高温性能的铁素体和马氏体钢；德文版 EN 10222-2:2017+A1:2021

This part of this European Standard specifies the technical delivery conditions for forgings for pressure purposes, made of ferritic and martensitic steels with specified elevated temperature properties. Chemical composition and mechanical properties are specified.NOTE Once this

Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties; German version EN 10222-2:2017+A1:2021

GSO EN 10272:2021 压力用不锈钢棒

This document specifies the technical delivery conditions for hot and cold formed stainless steel bars for the construction of pressure equipment supplied in accordance with one of the process routes and surface finishes listed in Table 5. The general technical delivery conditions in EN 10021 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.

Stainless steel bars for pressure purposes

GSO EN 10273:2021 具有指定高温性能的压力用热轧可焊钢筋

This European Standard specifies the technical delivery conditions for hot rolled weldable steel bars for the construction of pressure equipment for use at elevated temperatures. The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard. NOTE Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive 97/23/EC are satisfied, needs to be done.

Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties

DS/EN 10222-4:2021 承压用钢锻件第4部分：高屈服强度可焊细晶粒钢

Steel forgings for pressure purposes – Part 4: Weldable fine grain steels with high proof strength

DS/EN 10222-2:2021 压力用途钢锻件 第2部分：具有特定高温性能的铁素体和马氏体钢

Steel forgings for pressure purposes – Part 2: Ferritic and martensitic steels with specified elevated temperatures properties

NF A36-620-2*NF EN 10222-2+A1:2021 压力用途钢锻件 第2部分：具有特定高温性能的铁素体和马氏体钢

Steel forgings for pressure purposes - Part 2 : ferritic and martensitic steels with specified elevated temperatures properties

EN 10222-4:2017+A1:2021 承压钢锻件-第4部分:高弹限强度可焊接细晶钢 包含修改件A1,2021

This European Standard specifies the technical delivery conditions for forgings for pressure purposes, made of weldable fine grain steels with high proof strength. NOTE Once this standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. The series EN 10222-1 to EN 10222-5 is structured so that the data related to different materials is in the part allocated for that material. The presumption of conformity to the Essential Safety Requirements of Directive 2014/68/EU depends on both the text in part 1 and the data in part 2, 3, 4 or 5. General information on technical delivery conditions is given in EN 10021.

Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength

EN 10222-2:2017+A1:2021 承压钢锻件-第2部分:具备特定高温性能的铁素体和马氏体钢 包含修改件A1,2021

Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties

JIS G 3126:2021 低温压力容器用碳素钢板

Carbon steel plates for pressure vessels for low temperature service

ASTM A562/A562M-10(2021) 压力容器板 碳钢 玻璃或扩散金属涂层的锰 - 钛的标准规范

1.1 This specification2 covers titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other applications where the presence of free-iron carbide would be deleterious to the coating. A minimum specific ratio of titanium to carbon is specified. 1.2 The maximum thickness of plates is limited to 2 in. [50 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings

JIS G 3118:2020 中温和常温设备压力容器用碳素钢板

Carbon steel plates for pressure vessels for intermediate and moderate temperature services

ASTM A240/A240M-20a 用于压力容器的铬和铬镍不锈钢板 板和带的标准规范和一般应用

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications